• Applied Chemistry for Engineering
• /
• v.5 no.5
• /
• pp.819-824
• /
• 1994

A membrane-like $H_3PMo_{12}O_{40}$-polysulfone film was prepared by blending $H_3PMo_{12}O_{40}$ with polysulfone using dimethylformamide as a common solvent. SEM and EDX analysis showed that $H_3PMo_{12}O_{40}$ was uniformly and finely distributed in the film catalyst. The ESCA measurement also revealed that the oxidation state of Mo was not changed. The $H_3PMo_{12}O_{40}$-polysulfone catalyst showed lower activity for acid-catalyzed reaction and higher activity for oxidation reaction than $H_3PMo_{12}O_{40}$ in ethanol conversion reaction. The oxidation activity of the film catalyst was about 10 times higher than $H_3PMo_{12}O_{40}$. The decrease of acidic activity was due to DMF strongly adsorbed in acid sites of $H_3PMo_{12}O_{40}$, whereas the increase of oxidation activity was mainly due to uniform distribution of $H_3PMo_{12}O_{40}$. Adsorption results showed that the surface character of $H_3PMo_{12}O_{40}$ was drastically increased, while the bulk property of that was almost same after blending. It is suggested that the control of surface/bulk property as well as acid/redox property of heteropoly acid would be possible by blending it with a polymer.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.3
• /
• pp.366-370
• /
• 2006

We investigated the negative differential resistance (NDR) property of self-assembled 4,4-di(ethynylphenyl)-2'-nitro-l-(thioacetyl)benzene ('nitro-benzene'), which has been well known as a conducting molecule [1], Self-assembly monolayers (SAMs) were prepared on Au (111), which had been thermally deposited onto pre-treated $(H_2SO_4: H_2O_2=3:1)$ Si, The Au substrate was exposed to a 1mM solution of 1-dodecanethiol in ethanol for 24 hours to form a monolayer. After thorough rinsing of the sample, it was exposed to a $0.1{\mu}M$ solution of nitro-benzene in dimethylformamide (DMF) for 30 min and kept in the dark during immersion to avoid photo-oxidation. Following the assembly, the samples were removed from the solutions, rinsed thoroughly with methanol, acetone, and $CH_2Cl_2$, and finally blown dry with $N_2$. Under these conditions, we measured the electrical properties of SAMs using ultra high vacuum scanning tunneling microscopy (UHV-STM) and scanning tunneling spectroscopy (STS) [2]. As a result, we confirmed the properties of NDR in between the positive and negative region.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.69.1-69.1
• /
• 2010

We have fabricated organic photovoltaic cells (OPVs) with highly conductive poly 3,4-ethylenedioxythiophene : poly styrenesulfonate (PEDOT:PSS) layer as an anode without using transparent conducting oxide (TCO), which has been modified by adding some organic solvents like sorbitol (So), dimethyl sulfoxide (DMSO), N-methyl-pyrrolidone (NMP), dimethylformamide (DMF), and ethylene glycol (EG). The conductivity of PEDOT:PSS film modified with each additive was enhanced by three orders of magnitude. According to atomic force microscopy (AFM) study, conductivity enhancement might be related to better connections between the conducting PEDOT chains. TCO-free solar cells with modified PEDOT:PSS layer and the active layer composed of poly(3-hexylthiophene) (P3HT) and phenyl [6,6] C61 butyric acid methyl ester (PCBM) exhibited a comparable device performance to indium tin oxide (ITO) based organic solar cells. The power conversion efficiency (PCE) of the organic solar cells incorporating DMSO, So + DMSO and EG modified PEDOT:PSS layer reached 3.51, 3.64 and 3.77%, respectively, under illumination of AM 1.5 (100mW/$cm^2$).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.11
• /
• pp.727-730
• /
• 2015

In this paper, we fabricated organic compounds detector using the MWCNT/PMMA (multi-walled carbon nanotube / polymethylmethacrylate) composite film. We used polymer film as a matrix material for the device framework, and introduced CNTs for reacting with the organic compounds resulting in changing electrical conductivity. Spray coating method was used to form the MWCNT/PMMA composite film detector, and pattern formation of the detector was done by shadow mask during the spray coating process. We investigated changes of electrical conductivity of the detector before and after the organic compounds exposure. Electrical conductivity of the detector tended to decrease after the exposure with various organic compounds such as acetone, tetrahydrofuran (THF), toluene, and dimethylformamide (DMF). Finally we conclude that organic compounds detection by the MWCNT/PMMA composite film detector was possible, and expect the feasibility of commercial MWCNT/PMMA composite film detector for various organic compounds.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.11
• /
• pp.1579-1584
• /
• 2002

Since surfactant or emulsifiers remained on the nanoparticle surface significantly affect the physicochemical properties, the biodegradation rate, the biodistribution, and the biocompatibility of nanoparticles, surfactant-free nanoparticles should be good candidate. surfactant-free PLGA nanoparticles were successfully prepared by both the dialysis method and the solvent diffusion method. The PLGA nanoparticles prepared using the solvent diffusion method has a smaller particle size than the dialysis method. The solvent diffusion method was better for a higher loading efficiency than the dialysis method but the nanoparticle yield was lower. Testosterone (TST) release from the PLGA nanoparticles was dependent on the particle size rather than the drug contents. Testosterone release from the PLGA nanoparticles prepared by the solvent diffusion method using acetone was faster than those prepared by the dialysis method. TST release from the PLGA nanoparticles prepared by the solvent diffusion method using acetone and the dialysis method using dimethylformamide (DMF) was completed for 4 days while the PLGA nanoparticles prepared by the dialysis method using acetone showed approximately 80% TST release after 4 days. Since the PLGA nanoparticle degradation ratio was below 20% within 5 days at all samples while TST release completed within 4 days, TST release was dependent on the diffusion mechanism rather than degradation.

• Membrane and Water Treatment
• /
• v.7 no.6
• /
• pp.477-493
• /
• 2016

Immediate use of activated carbon incorporated polysulfone membrane application for dye separation was reported in this work. Dimethylformamide (DMF) was used as the solvent for the membrane preparation. The membrane thus prepared were characterized in terms of surface morphology, ATR-FTIR, AFM, experimental results as membrane performance. The resultant nanofiltration (NF) membranes were tested with Congo red dye concentration 200 mg/L. The water permeability was found to be considerably higher than that reported in literature. Experimental results show that the real rejection of the Congo red is 99.57% over the transmembrane pressure 100 psi using 30% activated carbon incorporated membrane. Prepared NF membranes shows the corresponding permeates fluxes were $40Lm^{-2}h^{-1}$ to $82Lm^{-2}h^{-1}$ with different activated carbon percentage incorporated in polysulfone membrane. The present study demonstrated that dye rejection enhanced NF may be a feasible method for the dye wastewater treatment. The overall observations thus indicated that toxic residual dyes can be appreciably separated from the membrane technology, provided that the accompanying polymeric membrane, activated carbon as binding agents and the process parameter levels are astutely selected.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.2
• /
• pp.297-304
• /
• 2013

Free-radical copolymerization of glycidyl methacrylate(GMA) and N-phthalimidoethyl acrylate(NPEA) were carried out at $60^{\circ}C$ in dimethylformamide(DMF) solution in the presence of benzoylperoxide(BPO) at low conversion. The polymers were characterized by IR and $^1H$-NMR. The compositions of the copolymer was analyzed by ultra violet(UV/Vis) spectrophotometry. The reactivity ratios of the monomer was determined by the application of Fineman-Ross(FR) and Kelen-T$\ddot{u}$d$\ddot{o}$s(KT) methods. The monomer reactivity ratios of the system and Alfrey-Price's resonance effect(Q) and polar effect(e) value for NIEA were determined as follow. The reactivity ratios of the monomer obtained from FR and KT are found to be $r_1$=0.87, $r_2$=0.98 and $r_1$=0.88, $r_2$=0.99 respectively. The Q and e values of poly(GMA-co-NPEM) calculated from $r_1$ and $r_2$ was Q= 1.31, e=0.75 respectively.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.11
• /
• pp.3259-3264
• /
• 2010

A label-free amperometric immunosensor has been proposed for the detection of myeloperoxidase (MPO) in human serum. To fabricate such an immunosensor, a composite film consisting of N,N-dimethylformamide (DMF), multiwall carbon nanotubes (MWCNTs) and 1-ethyl-3-methyl imidazolium tetrafluoroborate ($EMIMBF_4$) suspension was initially formed on a glassy carbon electrode (GCE). Then cerium dioxide ($CeO_2$) dispersed by chitosan was coated on the GCE. After that, MPO antibodies (anti-MPO) were attached onto the nano$CeO_2$ surface. With a noncompetitive immunoassay format, the antibody-antigen complex formed between the immobilized anti-MPO and MPO in sample solution. The immunosensor was characterized by cyclic voltammetry, transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The factors influencing the performance of the immunosensor were studied in detail. Under optimal conditions, the current change before and after the immunoreaction was proportional to MPO concentration in the range of 5 to $300\;ng\;mL^{-1}$ with a detection limit of $0.2\;ng\;mL^{-1}$.

• Korean Membrane Journal
• /
• v.4 no.1
• /
• pp.25-35
• /
• 2002

The gas permeation properties have been studied on carbon molecular sieve (CMS) membranes prepared by pyrolysis of P84 polyimide under various conditions. P84 polyimide shows high permselectivities (O$_2$/N$_2$= 9.17 and CO$_2$/N$_2$= 35) for various gas pairs and has a good processibility because it is easily soluble in high polar solvents such as N-methylpyrrolidinone (NMP), dimethylformamide (DMF), and N,N-dimethylacetamide (DMAc). After pyrolysis under Ar flow, the change in the heating rate was found to affect the gas permeation properties to some extent. The permeabilities of the selected gases were shown to be in the order He ＞ CO$_2$＞ O$_2$＞ N$_2$for all the CMS membranes, whose order was in accordance with the order of kinetic gas diameters. It also revealed that the pyrolysis temperature considerably influenced the gas permeation properties of the CMS membranes derived from P84 polyimide. The CMS membranes pyrolized at 700$\^{C}$ temperature exhibited the highest permeability with relatively targe loss in permselectivity. This means that the pyrolysis temperature should be varied in accordance with target gases to be separated.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1995.04a
• /
• pp.11-15
• /
• 1995

Polysulfone (PS) membranes were prepared by the phase inversion process using water or isopropanol as nonsolvent. The Flory-Huggins theory for a ternary system nonsolvent/solvent/polymer is applied to describe the thermodynamic equilibria of the components. The calculated ternary phase equilibria show that demixing of a PS binary solution with n-methylpyrrolidone (NMP) will be fast in a water coagulation bath and will be delayed in an isopropanol bath. The prepared membranes were characterized by SEM, gas adsorption-desorption measurement, and permeability test. The membrane, which is precipitated by fast demixing in a water bath, has nodular structures in the skin region and includes finger-like cavities in the sublayer. The membrane coagulated by isopropanol has a very dense and thick skin structure, which is formed by delayed demixing. The membrane coagulated by isopropanol showed considerably lower pore volume and surface area compared to that observed with water coagulation method. With dimethylformamide (DMF) as solvent and 2-3 wt% of water, the solution can show the liquid-liquid phase separation due to agglomation of the polymer-lean phase from the homogeneous solution. The membranes, which were coagulated near an equilibrium state, show the large (micron size) round pores in the whole membranes. The pores do not contribute the permeation characteristics.