• Polymer(Korea)
• /
• v.35 no.2
• /
• pp.130-135
• /
• 2011

Along with the fast development of electronics, the demands of portable electronics and wireless sensors are growing rapidly. The need for self-powering materials capable of powering the electrical devices attached to them is increasing, The piezoelectric effect of polyvinylidene fluoride (PVDF) can be used for this purpose. PVDF has a special crystal structure consisting of a ${\beta}$-phase that can produce piezoelectricity. In this paper, multilayer PVDF films were fabricated to increase the ${\beta}$-phase content. A solution of 10% concentration N;N-dimethylacetamide (DMAc) in PVDF (PVDF/DMAc) was used to fabricate the films via spin coating technique with the following optimum process parameters: a spin rate of 850 rpm, spin time of 60 s, drying temperature of $60^{\circ}C$, and drying time of 30 min, Compared with single-layer PVDF films, the multilayer films exhibited higher ${\beta}$-phase content. The ${\beta}$-phase content of the films increased gradually with increasing number of layers until 4, Maximum ratio of ${\beta}$-phase content was 7.72.

• Macromolecular Research
• /
• v.16 no.8
• /
• pp.725-733
• /
• 2008

Polyimide (PI) multilayer thin films were prepared by spin-coating from a poly(amic acid) (PAA) and poly(amic acid) ammonium salt (PAAS). PI was prepared from pyromellitic dianhydride (PMDA) and 4,4'-oxydianiline (ODA) PAA. Different compositions of PAAS were prepared by incorporating triethylamine (TEA) into PMDA-ODA PAA in dimethylacetamide. PI multilayer thin films were spin-coated from PMDA-ODA PAA and PAAS. The PAAS comprising cationic and anionic moieties were spherical with a particle size of $20{\sim}40\;nm$. Some particles showed layers with ammonium salts, despite poor ordering. Too much salt obstructed the interaction between the polymer chains and caused phase separation. A small amount of salt did not affect the interactions of the interlayer structure but did interrupt the stacking between chains. Thermogravimetric analysis (TGA) showed that the average decomposition temperature of the thin films was $611^{\circ}C$. All the films showed almost single-step, thermal decomposition behavior. The nanostructure of the multilayer thin films was confirmed by X -ray reflectivity (XRR). The LF 43 film, which was prepared with a 4:3 molar ratio of PMDA and ODA, was comprised of uniformly spherical PAAS particles that influenced the nanostructure of the interlayer by increasing the interaction forces. This result was supported by the atomic force microscopy (AFM) data. It was concluded that the relationship between the uniformity of the PAAS particle shapes and the interaction between the layers affected the optical and thermal properties of PI layered films.

• Membrane Journal
• /
• v.27 no.1
• /
• pp.53-59
• /
• 2017

In this study, the composite membranes prepared by sulfonated graphene oxide (sGO) and Nafion were developed as proton exchange membranes (PEMs) for polymer electrolyte membrane fuel cells (PEMFCs). The sGO/Nafion composite membranes were prepared by mixing Nafion solution with the sGO dispersed in a binary solvent system to improve dispersity of sGO. The composite membranes were investigated in terms of ionic conductivity, ion exchange capacity (IEC), FT-IR, TGA and SEM, etc. As a result, the binary solvent system, i.e., ortho-dichlorobenzene (ODB) and N,N-dimethylacetamide (DMAc), were used to obtain high dispersion of sGO particles in Nafion solution, and the ionic conductivity of the sGO/Nafion composite membrane showed $0.06Scm^{-1}$ similar to other research results at lower water uptake, 11 wt%.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.24 no.1
• /
• pp.105-113
• /
• 1995

Procedures for isolatin of chitin have been developed from crab(Chionoecetes opilio) shell waste with 26. 65% chitin on a dry basis. Optimal conditions for demineralization of crab shell were 1N HCl at ambient temperature for 30min with a solids to solbent ratio of 1 : 15(w/v). Optimal deproteinization involved treatment with 5% NaOH at $65^{\circ}C$ for 1 hr with a solids to solvent ratio of 1 : 15(w/v). Effective decoloration was achieved by bleaching with 0.32% sodium hypochlorite solution for 3min with a solids to solvent ratio of 1 : 10(w/v). Particular attentin was given to characterization of the physicochemical properties of the crab chitin. Chitins, from four different mesh sizes of crab shell, did not show significant differences in nitrogen and ash compositions. Bleaching decreased the viscosity of chitin but did not affect its solubility.

• Textile Coloration and Finishing
• /
• v.33 no.2
• /
• pp.72-78
• /
• 2021

The purpose of this study, the purpose of this study is to activate the antibacterial effect on the Chlorinated polyvinyl chloride film by using Octadecyldimethyl (3-triethoxy silylpropyl) ammonium chloride antibacterial agent with Chlorinated polyvinyl chloride polymer, which is inexpensive and has excellent properties such as heat resistance and chemical resistance. The Chlorinated polyvinyl chloride polymer was dissolved in a dimethylacetamide solvent, and film samples were prepared by varying the ratio of Octadecyldimethyl (3-triethoxy silylpropyl) ammonium chloride to study the antibacterial performance. A Scanning Electron Microscope-Energy Dispersive X-ray Spectrometer and X-ray photoelectron spectroscopy were employed to confirm the elements in the samples. According to the initial decomposition temperature of the Chlorinated polyvinyl chloride film and the Chlorinated polyvinyl chloride/Octadecyldimet hyl (3-triethoxy silylpropyl) ammonium chloride(10%) film using a Thermogravimetric analyzer(TA-DTA), it was confirmed that the initial decomposition temperature was lowered due to the influence of Octadecyldimethyl (3-triethoxy silylpropyl) ammonium chloride. In addition, in order to measure the mechanical properties, Universal testing machine was used and the result showed that a strength of Chlorinated polyvinyl chloride/Octadecyldimethyl (3-triethoxy silylpropyl) ammonium chloride(10%) was 36.8 MPa. The antimicrobial properties of the Chlorinated polyvinyl chloride/Octadecyldimethyl (3-triethoxy silylpropyl) ammonium chloride(10%) film showed 99.9% antimicrobial properties.

• Advances in materials Research
• /
• v.13 no.3
• /
• pp.243-251
• /
• 2024

The asymmetric polylactic acid (PLA) membrane was prepared via phase inversion method using non-solvent induced separation (NIPS) technique. This study aims to synthesized as well as to characterize the PLA membrane and evaluating the membrane performance on water flux and permeability. In addition, this research also studied the removal performance of methylene blue dye. The polymer solution has been prepared using 12 wt.% of PLA and dissolved in 88 wt.% of Dimethylacetamide (DMAc) as a solvent. Then, the cast film was immersed in different ratio of coagulant bath medium (distilled water: methanol: ethanol) ranging from 100:0:0, 75:25:0, 75:0:25 and 75:12.5:12.5, respectively). Several characterizations were performed which include, membrane contact angle and membrane porosity. Performance PLA membranes were determined in terms of water flux and permeability at 1 bar transmembrane pressure using dead-end permeation cell. Finally, methylene blue (MB) removal efficiency was tested at the same transmembrane pressure. The findings revealed that the increase of alcohol concentration in coagulant bath resulted in higher porosity and lower contact angle. In short, MB dye rejection efficiency is also closely related to the amount of alcohol ratio used in coagulant baths. Increases in concentration of methanol and ethanol in coagulant bath medium increases the membrane porosity thus increased in efficiency of methylene blue rejection.

• Korean Journal of Poultry Science
• /
• v.40 no.3
• /
• pp.171-178
• /
• 2013

The purpose of this study was to evaluate the sperm viability, normal acrosome and mitochondrial activity in the frozen-thawed fowl semen by different cryoprotectants. The experiment was carried out on 10 sexually adult roosters of Ogye. The semen was collected twice a week and pooled semen was diluted 1:1 EK extender containing no cryoprotectant at $5^{\circ}C$. After equilibration for 30 minutes, diluted chicken semen was diluted 1:1 extender containing either 7% dimethylacetamide (DMA), 7% dimethylformamide (DMF) or 7.5% methylacetamide (MA) at final concentration and was put in 0.5 mL plastic straws and frozen for 30 minutes by exposure to liquid nitrogen vapor 4 cm above the surface of liquid nitrogen, followed by plunging into liquid nitrogen. Frozen semen was thawed in water bath at $5^{\circ}C$ for 2 minutes. For cytometric analysis, the frozen-thawed semen was diluted with EK extender to a final concentration of 90 million spermatozoa per mL. Sperm membrane integrity was evaluated as SYBR-14 and propidium iodide (PI). Acrosome integrity was assessed with fluorescein isothiocyanate-labeled PSA and PI. The percentage of mitochondrial function was estimated by using Rhodamine123 (R123) and PI. In conclusion, freezing rooster semen by using 7% DMF as cryoprotectant was significantly highest in rates of survival and mitochondrial function while its rate of damage of acrosome was significantly lowest. As a result, DMF is the cryoprotectant that has the lowest influences on sperm membranes and acrosome integrity. Therefore it could be used for freezing method of animal genetic conservation method for poultry diversity.

• Applied Chemistry for Engineering
• /
• v.9 no.2
• /
• pp.185-192
• /
• 1998

Four kinds of polyamicacids(PAAs) were prepared by the condensation reaction of four diamines with different linkages, 3,3'-diaminodiphenyl sulfone(3,3'-$DDSO_2$), 4,4'-diaminodiphenyl sulfone(4,4'-$DDSO_2$), 4,4'-methylene dianiline(4,4'-MDA) and 4,4'-oxydianiline(4,4'-ODA), and dianhydride, 3,3', 4,4'-benzophenone tetracarboxylic dianhydride (BTDA) using the solvent, dimethylacetamide(DMAc). These four PAAs were blended with poly[2,2-(m-phenylene)-5,5'-bibenzimidazole](PBI) from the solution blending. Then called as Blend-I, II, III, and IV, respectively. Cast films or precipitated powders of the PBI/PAA blends were cured at a higher temperature than expected Tg to transform into PBI/PIs blends. Miscibility, specific intermolecular interaction for miscibility and their relative strength as a function of polyimide chemical structure with different four diamines in the PBI/PI systems were investigated. Four blends used in this study were all miscible, and the specific intermolecular interactions existing in these blends was thought to be the hydrogen bonding between the N-H of PBI and the C=O of PIs. The hydrogen bonding in the blends were shown to be stronger in the Blend-III and Blend-IV than Blend-I and II. It is speculated that the differences of hydrogen bonding strength of PBI/PI blends are dependent upon chemical structures of PIs, that is, PIs consisting of $SO_2$ group have a weaker hydrogen bonding strength than those of O or $CH_2$ group because the former has a larger spacer than the latter.

• Membrane Journal
• /
• v.18 no.4
• /
• pp.282-293
• /
• 2008

Partially sulfonated poly(aryl ether sulfone) membranes were prepared from the sulfonated sulfone monomer, which was synthesized by a nucleophilic substitution, non-sulfonated monomers and potassium carbonate by a direct polymerization method and a subsequent solution casting technique with mixed solvents of N-methyl-2-pyrrolidone (NMP) and dimethylacetamide (DMAc). To investigate the effect of mixed solvent, the volume ratios of NMP and DMAc were varied in the range of $0{\sim}100%$ and the degrees of sulfonation of the copolymers were fixed as 50%. The surface properties of the resulting membranes were examined by scanning electron microscope (SEM) and atomic force microscope (AFM), and a comparative study of the morphology changes and the physicochemical properties such as proton conductivity and methanol permeability was achieved. It was found that proton conductivities depend on the volume ratio of NMP-DMAc mixed solvents, and the proton conductivity determined at the condition of $25^{\circ}C$ and 100% relative humidity was $1.38{\times}10^{-1}\;S/cm$ for the membrane prepared in the 50:50 v/v-% of NMP : DMAc mixed solvent.

• Membrane Journal
• /
• v.33 no.6
• /
• pp.439-446
• /
• 2023

Ceramic membranes are generally used for various industrial processes operating under extreme conditions because of its high thermal and chemical stability. However, due to the trade-off phenomenon of permeability and mechanical strength, preparation of high permeability-high strength membrane is necessary. In this study, the change in characteristics and performances of ceramic membranes was analyzed depending on the type of polymer binder and its mixing ratio. Because the solubility between solvent and polymer binder was higher in PSf (polysulfone) than in PES (polyethersulfone), the viscosity and discharge pressure of the PSf-based dope solution were higher than those of PES-based dope solution. When PSf was used as a polymer binder, ceramic membrane showed high mechanical strength and low water permeability due to the dense structure. On the other hand, in case of PES, the mechanical strength was slightly reduced and the water permeability was increased. It was confirmed that the optimum mixing ratio of the PSf and PES with high water permeability and mechanical strength was 9:1.