• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.292-292
• /
• 2016

Transition metal dichalcogenides (TMDs) with a two-dimensional layered structure have been considered highly promising materials for next-generation flexible, wearable, stretchable and transparent devices due to their unique physical, electrical and optical properties. Recent studies on TMD devices have focused on developing a suitable doping technique because precise control of the threshold voltage ($V_{TH}$) and the number of tightly-bound trions are required to achieve high performance electronic and optoelectronic devices, respectively. In particular, it is critical to develop an ultra-low level doping technique for the proper design and optimization of TMD-based devices because high level doping (about $10^{12}cm^{-2}$) causes TMD to act as a near-metallic layer. However, it is difficult to apply an ion implantation technique to TMD materials due to crystal damage that occurs during the implantation process. Although safe doping techniques have recently been developed, most of the previous TMD doping techniques presented very high doping levels of ${\sim}10^{12}cm^{-2}$. Recently, low-level n- and p-doping of TMD materials was achieved using cesium carbonate ($Cs_2CO_3$), octadecyltrichlorosilane (OTS), and M-DNA, but further studies are needed to reduce the doping level down to an intrinsic level. Here, we propose a novel DNA-based doping method on $MoS_2$ and $WSe_2$ films, which enables ultra-low n- and p-doping control and allows for proper adjustments in device performance. This is achieved by selecting and/or combining different types of divalent metal and trivalent lanthanide (Ln) ions on DNA nanostructures. The available n-doping range (${\Delta}n$) on the $MoS_2$ by Ln-DNA (DNA functionalized by trivalent Ln ions) is between $6{\times}10^9cm^{-2}$ and $2.6{\times}10^{10}cm^{-2}$, which is even lower than that provided by pristine DNA (${\sim}6.4{\times}10^{10}cm^{-2}$). The p-doping change (${\Delta}p$) on $WSe_2$ by Ln-DNA is adjusted between $-1.0{\times}10^{10}cm^{-2}$ and $-2.4{\times}10^{10}cm^{-2}$. In the case of Co-DNA (DNA functionalized by both divalent metal and trivalent Ln ions) doping where $Eu^{3+}$ or $Gd^{3+}$ ions were incorporated, a light p-doping phenomenon is observed on $MoS_2$ and $WSe_2$ (respectively, negative ${\Delta}n$ below $-9{\times}10^9cm^{-2}$ and positive ${\Delta}p$ above $1.4{\times}10^{10}cm^{-2}$) because the added $Cu^{2+}$ ions probably reduce the strength of negative charges in Ln-DNA. However, a light n-doping phenomenon (positive ${\Delta}n$ above $10^{10}cm^{-2}$ and negative ${\Delta}p$ below $-1.1{\times}10^{10}cm^{-2}$) occurs in the TMD devices doped by Co-DNA with $Tb^{3+}$ or $Er^{3+}$ ions. A significant (factor of ~5) increase in field-effect mobility is also observed on the $MoS_2$ and $WSe_2$ devices, which are, respectively, doped by $Tb^{3+}$-based Co-DNA (n-doping) and $Gd^{3+}$-based Co-DNA (p-doping), due to the reduction of effective electron and hole barrier heights after the doping. In terms of optoelectronic device performance (photoresponsivity and detectivity), the $Tb^{3+}$ or $Er^{3+}$-Co-DNA (n-doping) and the $Eu^{3+}$ or $Gd^{3+}$-Co-DNA (p-doping) improve the $MoS_2$ and $WSe_2$ photodetectors, respectively.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.45 no.2
• /
• pp.261-268
• /
• 2016

This study was conducted to establish roasting conditions for optimization of Citri Unshii Pericarpium antioxidant activity using response surface methodology (RSM). A central composite design was applied to investigate the effects of two independent variables, namely roasting temperature ($40{\sim}100^{\circ}C$; $X_1$) and roasting time ($5{\sim}15min$; $X_2$), on responses such as electron donating ability ($Y_1$), total phenolic content ($Y_2$), total flavonoid content ($Y_3$), and hydroxyl radical scavenging activity ($Y_4$). The maximum electron donating ability was 72.38% at a roasting temperature of $71.12^{\circ}C$ and roasting time of 9.39 min. The maximum total phenolic content was 10.76 mg tannic acid equivalents/g at a roasting temperature of $69.71^{\circ}C$ and roasting time of 8.39 min. The maximum total flavonoid content was 105.99 mg quercetin equivalents/100 g at $72.54^{\circ}C$ and 8.64 min. The maximum hydroxyl radical scavenging activity was 60.33% at $68.97^{\circ}C$ and 9.84 min. Based on the superimposition of three dimensional RSM with respect to electron donating ability, total phenolic content, total flavonoid content, and hydroxyl radical scavenging activity under various conditions, optimum conditions were established as follows: roasting temperature of $70.90^{\circ}C$ and roasting time of 9.03 min.

• The Korean Journal of Pesticide Science
• /
• v.14 no.4
• /
• pp.319-325
• /
• 2010

To understand the influences of the substituents ($R_1{\sim}R_4$) on insecticidal activity of N'-phenyl-N-methylformamidine analogues (1~22) against two spotted spider mite (Tetranychus urticae), comparative molecular field analysis (CoMFA) model and comparative molecular similarity indices analysis (CoMSIA) model as three dimensional quantitative structure-activity relationships (3D-QSARs) model were derived and discussed quantitatively. From the results, the correlativity and predictability ($r^2{_{cv.}}=0.575$ and $r^2{_{ncv.}}=0.945$) of the CoMFA 1 model were higher than those of the rest models. The the CoMFA 1 and CoMSIA 1 model with the sensitivity of the perturbation and the prediction produced ($d_q{^{2'}}/dr^2{_{yy}}=1.071{\sim}1.146$ & $q^2=0.545{\sim}0.626$) by a progressive scrambling analysis were not dependent on chance correlation. The insecticidal activities from the optimized CoMFA 1 model were depend upon the steric field (62.5%), electrostatic field (28.9%), and hydrophobic field (8.6%) of N'-phenyl-N-methylformamidine analogues. Therefore, the inhibitory activities with optimized CoMFA 1 model were dependent upon steric factor. From the contour maps of the optimized models, it is predicted that the structural distinctions that contribute to the insecticidal activity will be able to applied new potent insecticides design.

• Cartoon and Animation Studies
• /
• s.51
• /
• pp.293-319
• /
• 2018

Thanks to the advancement of the related technologies and equipment, today's video contents like movies, animations and soap operas are rapidly expanding their expressible cinematic imagination area. In order to fulfill the elevated visual expectations of audiences and realize exciting storytelling and fantastic world, the fusion of different techniques is actively used, and the reality for visual effects and image synthesis is increasing more and more. Accordingly, recent VFX-oriented movies using CG have a much more complicated production process than before. Therefore, the importance of Pre-visualization, aka Pre-vis is becoming bigger in the planning process for sophisticated design. Pre-vis means that the advance visualization for stories or directing ideas in the planning process before starting production of movies or animations. 3D animated Pre-visualization realizing directors' abstract and ambiguous ideas in 3 dimensional environment in advance is, as a powerful means for visual storytelling, briskly used focusing on the VFX film industry on which the present CG is broadly used, and the role of Pre-vis throughout productions has increased compared to the past. The studies, however, on the role and utility of Pre-vis are not enough. Therefore, this study was conducted on the role of Pre-vis used for present VFX movie productions using the examples of 3D animated Pre-visualization production in which the researcher of this study participated. In this study, the role of the Pre-vis that is subdivided presently, is divided into and 3D animatics and their each role is analyzed with the example images. Through this, the characteristics that Pre-vis should have are clarified and the concept of the advantages and utility led by the use of Pre-vis in productions is strengthened. The goal of this study is to induce active uses of Pre-vis throughout productions after forming consensus about the various roles of Pre-vis and their utility.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.32 no.1
• /
• pp.10-21
• /
• 2014

This study focuses on the landscape of Daegodae(大孤臺), a prominent rock placed at the side of Namgae Stream in Hamyang, and the person who enjoy the landscape. Through the analysis of the letters such as names carved on the rocks based on ancient poetry and stone walls, the study examines the characteristics of the landscape and the space of Daegodae and the phase of hegemony to enjoy the landscape and space. The result of this study is as follow.2) There are 5 Seowon(書院: lecture halls) nearby Daegodae identified in the ancient map has 5 auditoriums nearby, and three-dimensional volume and eccentricity of the Daegodae is impressive. Daegodae, named by Noh Jin(1518~1578) in 16th century, was used in a variety of ways, including viewing, game, recreation, and meeting, by the staff of the lecture halls including Namgae Seowon(南溪書院), as a result of analyzing the ancient document Go-dae-il-Loc(孤臺日錄) written by Jung Kyung-Woon(鄭慶雲: 1556~?). The structure of Daegodae is that there is Chunggeunchung(淸近亭) on the rock face of the top and Sanangjae(山仰齋) to the west around the memorial stone for Yang Hee(梁喜: 1515~1581). The upper part of the foundation of Daegodae with 11m high and $10m^2$ wide to the east and west was widely used for lecturing and poetry reading. To the north and west of the foundation were the writing of Kim Jeong-Hee(金正喜: 1786~1856) with the words 'Seoksong Chusa(石松 秋史)' carved on the rock and the remains of a dead tree that is presumed to have been called as 'Seoksong'. They are the landscapes that further enhance the history and authenticity of this place. The two kinds of letters carved on the rock 'Daegodae Gaeeunseo(大高臺 介隱書)' and 'Mukheon JungGeunSang(鄭近相: 1893~1934)' were recorded each by Jung Jae-Gi(1811~1879) and his grandson Jung Geun-Sang, which are, as the outcome of exclusive space possession and space hegemony, the signatures indicating that they were the persons who enjoyed this place during the late Joseon and Japanese colonial era. In other words, Daegodae had some implied meaning of preoccupancy of the place as Gujolyangseonsengjangguso since the middle of Joseon, and the place was passed down as a buddhism lecturing and memorial venue called "Dungbukganghoiso Cheonryungjaeseonhyunjangguso" after going through the space hegemony of Jung Jae-Gi and Jung Geun-Sang during the late Joseon and Japanese colonial era each, Nevertheless, a number of letters carved on the rock identified also imply that 'Hadong Jung(河東鄭氏)' and 'Pungcheon Noh(豊川盧氏)' were those who enjoyed the landscape of Daegodae and the center of the space hegemony. The "letters carved on the rock of Daegudae" is another case of cultural landscape and traditional gardening space that serves as the representation of the will of enjoying the landscape in this place and the history of space hegemony.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.4
• /
• pp.557-566
• /
• 2005

In preparation of steamed foam-cakes, effects of whipping time, amount of wheat flour, and amounts of emulsifier on physical properties of the steamed foam cakes were investigated using RSM (response surface methodology). The three independent variables selected for the RSM experiment were whipping time $(X_1)$, amount of wheat flour $(X_2)$, and amounts of wheat flour $(X_2)$, and concentration of emulsifier $(X_3)$ were set for single-stage mixing, respectively. A rotatable central composite design was used for treatment arrangement. The responses from the product for loaf volume, color values and textural properties were analysed. In the analysis of variance for the foam cakes prepared by single-stage method, significant interactions were observed between independent variables (experimental factors) and physical property like loaf volume (p<0.05); textural properties like hardness, gumminess, and chewiness (p<0.05). Among independent variables, concentration of emulsifier had the most effects on physical properties while whipping time. The ordinary points in surface response showed maximal points with physical property like colorimetric b value while other properties revealed saddle points. The 3-dimensional response surface graphs of the predicted regression models displayed decreasing loaf volumes with increasing whipping times and emulsifier concentrations beyond optimum levels. The optimum conditions for best loaf volume and textural property (hardness, gummimess and chewiness) of the products selected by extracting intersectional areas of the contour maps that commonly overlapped all characteristics were; $11\~13$ min whipping time, $470\~486\;g$ amount of wheat flour, and $19\~20\;g$ emulsifier concentration, in case of single-stage method. The median values extracted from the RSM experimental results for optimum manufacturing conditions for single-stage method, i.e., 12 min whipping time, 478 g amount of wheat flour, and 20 g emulsifier concentration were empirically proven to fit the predicted levels of physical properties from the final foam cakes.

• Korean Journal of Food Science and Technology
• /
• v.30 no.5
• /
• pp.1189-1196
• /
• 1998

Extraction conditions were optimized using response surface methodology for preparing high-quality ethanol extracts from cultivated Chrysanthemum petals. A fractional factorial design was applied to investigate effects of solvent ratio to sample $(X_1)$, ethanol concentration $(X_2)$ and extraction time $(X_3)$ at $60^{\circ}C$ on dependent variables of the extract properties, such as yellow color $(Y_1)$, carotenoids $(Y_2)$, soluble solids $(Y_3)$, phenolic compounds $(Y_4)$, electron donating ability $(Y_5)$, sensory color $(Y_6)$ and sensory aroma $(Y_7)$. Second-order models were employed to generate 3-dimensional response surfaces for dependent variables and their coefficients of determination $(R^2)$ were ranged from 0.8063 to 0.9963. Optimum extraction conditions for each variable were 115 mL/g, 97%, 18 hr in yellow color, 145 mL/g, 50%, 12 hr in carotenoids, 147 mL/g, 48%, 17 hr in soluble solids, 116 mL/g, 68%, 17 hr in phenolic compounds, 110 mL/g, 98%, 14 hr in electron donating ability, 101 mL/g, 48%, 54 hr in organoleptic color and 109 mL/g, 54%, 4 hr in organoleptic aroma, respectively. The range of optimum conditions at 16hr extraction for maximized characteristics of ethanol extracts was $103{\sim}122\;mL/g$ and $64{\sim}78%$. Predicted values at the optimum condition agreed with experimental values.

• Science of Emotion and Sensibility
• /
• v.19 no.4
• /
• pp.21-32
• /
• 2016

Studies have observed various phenomena regarding the effect of the interaction between type, price, and brand image of a product on consumers' purchase intent and product quality perception. Yet, few have studied the effect of the interaction between product type and manufacturing method on these factors. However, the advent of three-dimensional (3D) printers added a new manufacturing method, 3D printing, to the traditional methods of handicraft and automated machine-based production, and research is necessary since this new framework might affect consumers' purchase intent and product quality perception. Therefore, this study aimed to verify the effects of the interaction between product type and manufacturing method on purchase intent and product quality perception. To achieve this, in our experiment 1, we selected product types with different characteristics (drone vs. violin vs. cup), and measured whether consumers preferred different manufacturing methods for each product type. The results showed that consumers preferred the 3D printing method for technologically advanced products such as drones, the handmade method for violins, and the automated machine-based manufacturing method, which allows mass production, for cups. Experiment 2 attempted to verify the effects of the differences in manufacturing method preferences for each product type on consumers' purchase intent and product quality perception. Our findings are as follows: for drones, the purchase intent was highest when 3D printing was used; for violins, the purchase intent was highest when the violins were handmade; for cups, the purchase intent was highest when machine-based manufacturing was used. Moreover, whereas the product quality perception for drones did not differ across different manufacturing methods, consumers perceived that handmade violins had the highest quality and that cups manufactured with 3D printing had the lowest quality (the purchase intent for cups was also lowest when 3D printing was used). This study is anticipated to provide a wide range of implications in various areas, including consumer psychology, marketing, and advertising.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.1-6
• /
• 1976

This paper is the third one of the study on balanced type oscillating mole-drainer, the first one was presented in No 9. Gyeongsang College Report and the second one in Vol. 17, No.4 of the KSAE. In the first part of this study, the characteristics of traction forces between the nonoscillating earth working equipments and oscillating ones was compared. A model of the balanced type oscillating mole-drainer, which composed of a mechanism that may reduce the machine vibration, was designed following the dimensional analysis and similitude technique. The model test was carried out to clarify the balancing mechanism of the oscillating parts and other parts of the machine. In the light of the results from the model tests, a prototype machine was made for experimental purpose. Results from the field test by a reported in the near future. In the second report, the model tests were carried out under the same soil conditions, i.e, . oscillating frequency, running velocity, and oscillating amplitude, etc. It was clear that use of balanced type oscillating model could substantially reduce the vibration of the whole system of the machine, when compared with the nonoscillating type model. In this paper(the third report), results of investigation on the traction force, power requirement, and moment. etc, is presented. Analysis of variance technique was used for analyzing the effect of the frequency, amplitude, and running velocity on the draft force, torque, power requirements, and moments. The results obtained from the model tests are as follows, 1) By practicing a balanced-type oscillating mole-drainer, it was possible to reduce the traction resistance by 55.1-61. 2 percent of traction resistance, however, was 1.75 - 1.95 times greater than the value of resistance which was induced by use of a mole-drainer with single bullet. The resistance of rear shank against soil was considered as a main causing factor of the above results. 2) As the oscillation frequency was increased, the traction resistance was decreased. Considering on the effect of oscillation the greater the amplitude, and the slower the running velocity was, the greater the reduction ratio of traction resistance was. 3) The ratio of the traction resistance of oscillating mole-drainer to that of non-oscillating one could be represented as a function of dimensionless variable (V/$Af$). The results from the tests were well agreed with the reported results from the experim ents on oscillation plow or hoe. 4) By taking a lower value of (V/$Af$), reducing the traction resistance was possible. This fact meant, however, that the efficiency of mole drain practice would be lower. 5) It was experimentally confirmed under the same condition of soil that the variable (R/$rD1^3$) could be represented as a function of a variable($V^2/gD$) when a non\ulcornerocillating mole-drainer was used. 6) When a oscillating mole-drainer was used, the variable(R/$rD_1^{3}$) could be represented as a function of two variables ($v^2/gD_1$) and (V^2/gD_1$). 7) The torque was not affected by a change of frequency. However, a relation of proportionality existed between torque and amplitude, running velocity, and ratio of bullet diameter. When a balanced type oscillating mole-drainer with two bullets was used, torque was increased by 52.8-78. 4 percent and total power requirement was also increased. 8) Total power requirement was increased linearly in accordance with the increasing frequency, 41.96 percent of total power was used for oscillating action. The magnitude of total power requirement was 1. 8-9. 4 times greater than that of a non-oscillating mechanism. In the view point of power requirement, it was not advisable to increase the frequency, amplitude, running velocity, and ratio of bullet diameter at the same time. 9) Only the positive moment occured in the rear shank. Change of the diameter of a rear bullet, could not affect the balancing against the soil resistance. It was necessary for rear bullet to have a large resistance against soil only when the rear bullet was in backward motion. 10) Within an extent of the experimental base, optimum limits for several design factors were A=0.5cm, $f$=22.5Hz, V=O. 05m/sec, and $\lambda$=1.0 By adapting these values traction resistance was reduced by 40 percent and vibration acceleration wa s reduced by 60 percent. Even though the total , power requirements for operating a balanced type oscillation mechanism was greater ~than that of non-oscillating one, using a oscillating mechanism would be more effective. Because a balanced type oscillating mechanism is used, tractive resistance will be reduced and then the lighter . tractive equipment could be used.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.26 no.2
• /
• pp.179-195
• /
• 2010

In the internal connection system, the loading transfer mechanism within the inner surface of the implant and also the stress distribution occuring to the mandible can be changed according to the abutment form. Therefore it is thought to be imperative to study the difference of the stress distribution occuring at the mandible according to the abutment form. The purpose of this study was to assess the loading distributing characteristics of three different abutments for GS II$^{(R)}$ implant fixture(Osstem, Korea) under vertical and inclined loading using finite element analysis. Three finite element models were designed according to three abutments; 2-piece Transfer$^{TM}$ abutment made of pure titanium(GST), 2-piece GoldCast$^{TM}$ abutment made of gold alloy(GSG), 3-piece Convertible$^{TM}$ abutment with external connection(GSC). This study simulated loads of 100N in a vertical direction on the central pit(load 1), on the buccal cusp tip(load 2) and $30^{\circ}$ inward inclined direction on the central pit(load 3), and on the buccal cusp tip(load 4). The following results were obtained. 1. Without regard to the loading condition, greater stress was concentrated at the cortical bone contacting the upper part of the implant fixture and lower stress was taken at the cancellous bone. 2. When off-axis loading was applied, high stress concentration observed in cervical area. 3. GSG showed even stress distribution in crown, abutment and fixture. GST showed high stress concentration in fixture and abutment screw. GSC showed high stress concentration in fixture and abutment. 4. Maximum von Mises stress in the surrounding bone had no difference among three abutment type. In GS II$^{(R)}$ conical implant system, different stress distribution pattern was showed according to the abutment type and the stress-induced pattern at the supporting bone according to the abutment type had no difference among them.