• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.456-459
• /
• 2004

Analog film/screen systems have been being changed to a digital x-ray imaging device using direct conversion materials. Photocoductors for a direct detection flat-panel imager require high x-ray absorption, ionization and charge collection, low leakage current and large area deposition. In this work, $HgI_2$ films with excellent properties for x-ray detector were deposited by screen printing method. The thickness of $HgI_2$ film was about $150\;{\mu}m$. The passivation layer is fabricated using a-Se and parlyene, the both fabrication $HgI_2$ film were compared for analyzing the leakage current reduction. We measured electrical properties-leakage current, photosensitivity, SNR though I-V measurement, As the result, $HgI_2$ film using a-Se passivation layer had the greater

• Journal of the Korean Society of Radiology
• /
• v.7 no.6
• /
• pp.389-395
• /
• 2013

This study intended to investigate the optimum conditions for lumbar test that has the highest level of irradiation conditions among general test sites. To to this, the most widely used irradiation conditions in terms of statistics were set as standards; test groups applied with DMF were selected; tests groups suitable for clinical trials were selected by using suggested patient dose. Blind tests were conducted by 10 specialists and radiologists. The results suggested that under the optimum conditions, the radiation dose reduction of 2.09 mGy, 4.42 mGy and 3.65 mGy can be achieved in forward-backward test, lateral test and 4-direction test, respectively. There is a need of further studies on the optimization of irradiation conditions in accordance with the conditions of patients.

• Journal of Power System Engineering
• /
• v.13 no.5
• /
• pp.95-102
• /
• 2009

A steam generator (boiler) in thermal power plants, consisting of more than 30,000 parts and components, can lead to the plant shutdown with damage to even the small part of the components; esp., like weld failures on boiler tubes. Consequently it is greatly demanded to improve the quality of the weld on the boiler tube for the stable operation of the power plants. Because of the feature of the welding, which is done past by melting the work pieces and adding a filler material that cools to become a strong coalescence, there is a great possibility that weld failures take place. As a result, it is regulated to make a non-destructive testing, like radiography test, to detect defects and flaws in the weld. The current film radiography test provides a lower image quality exceeding 2.0% of a basic quality level for a penetrameter, it is very likely to fail to detect micro defect. As a result, the prevention for the boiler tube failure has not been made effectively. In this study, computed radiography technology has been applied as a digital radiography test to the boiler tube weld, and Se-75 radiation source was used to improve the image quality, instead of Ir-192 source. As a result of this study, it is proven to save the time and cost for test and to enhance the quality level of penetrameter penetrating image, which enables to upgrade the quality of radiography test to the boiler tube weld.

• Advances in Computational Design
• /
• v.5 no.2
• /
• pp.127-146
• /
• 2020

Building Information Modeling (BIM) is increasingly used throughout the facility's life cycle for various applications, such as design, construction, facility management, and maintenance. For existing buildings, the geometry of as-built BIM is often constructed using dense, three dimensional (3D) point clouds data obtained with laser scanners. Traditionally, as-built BIM systems do not contain the material and textural information of the buildings' elements. This paper presents a semi-automatic method for generation of material and texture rich as-built BIM. The method captures and integrates material and textural information of building elements into as-built BIM using thermal infrared sensing (TIS). The proposed method uses TIS to capture thermal images of the interior walls of an existing building. These images are then processed to extract the interior walls using a segmentation algorithm. The digital numbers in the resulted images are then transformed into radiance values that represent the emitted thermal infrared radiation. Machine learning techniques are then applied to build a correlation between the radiance values and the material type in each image. The radiance values were used to extract textural information from the images. The extracted textural and material information are then robustly integrated into the as-built BIM providing the data needed for the assessment of building conditions in general including energy efficiency, among others.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.959-966
• /
• 2015

In this paper, we propose an indoor visible light communication(VLC) localization using Walsh code which can identify overlapped signals transmitted from the different LED sources as each of orthogonal signal at a receiver and using Manchester code which can eliminate the flicker of LED light and maintain a constant brightness. The proposed system can estimate the relative position of the receiver by using Lambertian radiation properties and trilateration method that are applied to the location information of fixed LED sources and the received signals from them. In order to verify the feasibility of the proposed system, we carried out the simulation in an indoor space with $6{\times}6{\times}1.5m^3$ installed LED lamps of 16. The simulation result shows that the proposed method achieves an average positioning error of 0.0536 m and a maximum positioning error of 0.2977 m.

• The Journal of the Korea Contents Association
• /
• v.10 no.3
• /
• pp.266-270
• /
• 2010

In case of the Dental X-ray apparatus, the diameter (or the field size) of the tip of the cone should be less than 7 cm according to the Diagnosis Radiation Equipment Safety Management. However, deviation from the field is not expected to be big as photography is made at close range from the skin. Also, as the size of film or digital detector used in intra-oral photography is $3\times4cm^2$, the size mentioned above can be considered to be much bigger. Furthermore, the patient dose by short-distance photography can not be ignored. Therefore, effect on the patient dose, resolution and image qualty was examined by reducing the cone diameter by 0.5 cm interval. The result showed that the patient dose was reduced and a partial improvement in picture contrast was observed. Therefore, it can be concluded from these results that further investigation may be worthwhile in terms of policy.

• Journal of the Korean Society of Radiology
• /
• v.14 no.4
• /
• pp.391-396
• /
• 2020

In this study, we developed a phosphor film screen that can be applied to radiographs during non-destructive testing using Gd₂O₂S:Tb phosphor compounds. The image uniformity of the fabricated phosphor screen film was analyzed by FE-SEM, RMS and RDS analysis. In addition, the tensile strength, elongation, and modulus of elasticity of the Gd₂O₂S:Tb phosphor screen were evaluated by measuring the stress-strain characteristic curve. As a result, it was evaluated that the RSD value had an excellent image uniformity within 10% of the evaluation criteria. In addition, as a result of evaluation of physical properties, the tensile strength was 1.1760 N/㎟, the tensile strength at break was 1.1515 N/㎟. These results suggest that the Gd₂O₂S:Tb phosphor screen fabricated using the room temperature gel-printing method could be applied to digital radiography detectors for radiography.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.15 no.4
• /
• pp.291-297
• /
• 2013

Automated weather stations were installed at 9 locations with, three different elevations, (i.e., 50m, 100m, and 300m a.s.l.) with different slope and aspect in a small watershed ($50km^2$ area). Air temperature at 1500 LST and solar radiation accumulated for 1100-1500 LST were collected from January to December 2012. Topography of the study area was defined by a $30{\times}30$ m digital elevation model (DEM) grid. Accumulated solar irradiance was calculated for each location with the spatially averaged slope and aspect of surrounding circles with 5, 10, 15, 20, 25, and 30 grid cell radii, respectively. The 1500 LST air temperature from clear sky conditions with zero cloud amount was regressed to the 1100-1500 LST solar irradiance at 9 locations. We found the highest coefficient of determination ($r^2$ = 0.544) at 25 grid cell radius and the temperature variation in this study was explained by Y = 0.8309X + 0.0438, where Y is 1500 LST temperature (in $^{\circ}C$) and X is 1100-1500 LST accumulated solar irradiance (in $MJ/m^2$).

• Journal of radiological science and technology
• /
• v.33 no.1
• /
• pp.1-10
• /
• 2010

Dental panoramic radiography is an imaging technique which shows the information of teeth, jaws and superficial structures on a single image. In this study, we propose the clinical dose reference for dental panoramic radiography. Dental panoramic radiography is an application which can increase the radiation does of oral cavity. It is very important to study the real condition of management for these panoramic X-ray equipments. Since there was no researches on dental panoramic equipments in domestic and foreign study groups, we measured and analyzed the dose such as effective dose, DAP and DWP of panoramic radiography.

• Textile Coloration and Finishing
• /
• v.21 no.1
• /
• pp.1-9
• /
• 2009

A lot of research has been made over the recent decade to develop testing packages with antimicrobial properties to improve food safety. In this study, a new method, experimental device and technology for environmental corresponding packages of polypropylene (PP) film has been developed to provide effective temperature buffering during the transport/long-term storage of grains or foodstuffs from the supplier to the market. This quantitatively optimized mixing system enabled to produce PP films with the 700$\sim$1,400d (width;1.5$\sim$3mm, thickness;0.01$\sim$0.5mm). In the whole mixing systems, the finely-granulated inorganic illite and PP virgin chip for master batch (M/B) chip was calculated by digital measurement methods, and then the M/B chip for PP film was adapted through a air jet and PP grinding method. The prepared PP film was characterized with tensile strength and elongation, far infrared radiation (FIR) emissivity, antimicrobial activity and deodorization properties. The results revealed that the two differently grain-sized illite could be show homogeneously dispersed on PP chip surface, and as the increasing of illite content, the FIR emissivity and the anion emission rate of film was increasingly improved. In both of 325 and 1,500 mesh-sized illite contained PP chip, of course the antimicrobial activity was good. But the ultimate deodorization rate for ammonia gas of PP film were found to be approximately the same.