• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.6
• /
• pp.111-116
• /
• 2018

Recently, shape manufacturing method has been changed to a 3D printer. Since lamination type manufacturing method is the basis for forming a three-dimensional shape by repeated lamination, the horizontal accuracy of the lamination layer is very important. In the current paper, we have proposed a new leveling system to be installed in a large 3D printer. The light source was reflected from the water surface contained in the measuring device, and the inclination of the measuring device was measured from the light that entered into four regions of a quarter photodetector. The electrical signals generated differently according to the position of the beam spot incident on the quarter photodetector was acquired and compensated to be horizontal by using a motor mounted at the corner. Compared to a digital leveler, the newly developed leveling system gave errors of only 2 to 3%. This new device can be applied to various fields including the 3D printer in future.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.26 no.1
• /
• pp.51-64
• /
• 2008

In this paper, an experiment was done where the input(scanner, digital still camera) and monitor(CRT, LCD) device used the linear multiple regression and the GOG (Gain-Offset-Gamma) characterization model to perform a color transformation. Also to color conversion method of the digital printer it used the LUT(Look Up Table), 3dimension linear interpolation and a tetrahedron interpolation method. The results are as follows. From color reappearance of digital printing case of monitor, the XYZ which it converts in linear multiple regression of input device it multiplied the inverse matrix, and then it applies the inverse GOG model and after color converting the patch of the result most which showed color difference below 5 at monitor RGB value. Also, The XYZ which is transmitted from the case input device which is a printer it makes at LAB value to convert an extreme, when the LAB value which is converted calculating the CMY with the LUT and tetrahedral interpolations the color conversion which considers the black quantity was more accurate.

• The Journal of the Korea Contents Association
• /
• v.15 no.1
• /
• pp.74-85
• /
• 2015

This study on the proofing what used to correct the color difference between the photo image and offset press. Printing photos with color offset press always make the differs, because of the difference in gamut. Photographer hopes to be able to use the proofing with inkjet printer for reduce these differences. In this study, I experiment with various ways for the proofing by photographer directly. It is using the ink jet printer and image outputs of the various mode was applied to a variety of color setting value. And calculate the output image using a spectrophotometer and compared with the image of offset press. At last I can found a very similar color setting value with the offset image. After all this research is to obtain a result of finding out proofing work flow through method to measure and how to apply various color setting value results.

• Journal of Technologic Dentistry
• /
• v.43 no.3
• /
• pp.71-76
• /
• 2021

Purpose: In this study, thermal properties were observed by measuring the extent of thermal expansion and the amount of thermal residue that appears upon burnout on a workpiece made by using a dental digital light processing (DLP) three-dimensional (3D) printer. Methods: Thermal properties of workpieces manufactured by using two 3D printers were observed. The specimens were designed in cylindrical form with dimensions 10 mm in diameter and 10 mm in height. The control specimen was made of wax, and the experimental specimen was made of resin. The thermal expansion rate was measured by applying heat to three types of specimens, and burnout residue was measured. Results: The thermal expansion rate of the wax pattern (WP) specimen was 0.93%±0.05%, of the RP1 specimen was 1.30%±0.08%, and of the RP2 specimen was 1.20%±0.09%. Measuring the recovered residue yielded residual amounts of 0.2% for the WP specimen, 1.1% for the RP2 specimen, and 1.8% for the RP1 specimen. Conclusion: 1. From measurements of the workpieces manufactured by dental DLP 3D printing, the thermal expansion rate was found to be higher than that of wax. 2. As a result of measuring burnout residues on the workpieces manufactured by dental DLP 3D printing, the required summoning temperature to obtain suitable castings was determined to >750℃.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1425-1429
• /
• 2007

Consumer's product selection measures are being shifted from the units' operational performance to overall performance. Low noise, low vibration, and low power consumption rate, etc. which used to be additional quality indices, now become vital performance factors. Especially, noise and vibration characteristics are being considered as equivalent to/or even more critical than operational performance in certain products such as office machines and home entertainment systems, which share the same space with human being's daily life. Therefore, noise reduction and sound quality improvement technology becomes an inevitable design issue for those applications. Qualitative noise characteristics of rotating polygonal disk applied to digital printer systems are presented. Overall sound pressure level change and tonal noise variation with respect to the geometrical properties of polygonal disk, operational speed, and others are briefly discussed based on experimental results.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.345-348
• /
• 2006

The piezoelectric thick films were fabricated on silicon substrates by screen printing method. By developing a low-temperature sinterable piezoelectric composition and a new poling technique, we fabricated the high-performance piezoelectric thick films on silicon which can be applied for piezoelectric MEMS applications such as micropumps of the ink jet printer heads.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.6
• /
• pp.606-611
• /
• 2008

Consumer's product selection measures are being shifted from the units' operational performance to overall performance. Low noise, low vibration, and low power consumption rate, etc. which used to be additional quality indices, now become vital performance factors. Especially, noise and vibration characteristics are being considered as equivalent to/or even more critical than operational performance in certain products such as office machines and home entertainment systems, which share the same space with human being's daily life. Therefore, noise reduction and sound quality improvement technology becomes an inevitable design issue for those applications. Qualitative noise characteristics of rotating polygonal disk applied to digital printer systems are presented. Overall sound pressure level change and tonal noise variation with respect to the geometrical properties of polygonal disk, operational speed, and others are briefly discussed based on experimental results.

• Journal of Korean society of Dental Hygiene
• /
• v.19 no.6
• /
• pp.1089-1097
• /
• 2019

Objectives: The purpose of this study is to assess the accuracy of provisional restorative resins fabricated using dental three-dimensional (3D) printers. Methods: Provisional restorative resins were fabricated using the first molar of the right mandibular. Three groups comprising a total of 24 samples of such resins were fabricated. The prepared abutment was scanned initially and then designed using a computer-aided design (CAD) software. The conventional subtractive manufacturing system was employed to fabricate the first group of resins, while the second and third groups were fabricated using a digital light processing (DLP) 3D printer and a stereolithography (SLA) 3D printer, respectively. The internal surfaces of the resins were scanned and 3D measurements of the resins were taken to confirm their accuracy. Results: The root-mean-square deviation (RMS±SD) of the accuracy of the resins fabricated using the conventional subtractive manufacturing system, DLP 3D printer, and SLA 3D printer were 68.83±2.22 ㎛, 74.63±6.23 ㎛, and 61.74±4.09 ㎛, respectively. A one-way analysis of variance (ANOVA) test showed significant differences between the three groups (p < 0.05). Conclusions: Provisional restorative resins fabricated using DLP and SLA 3D printers demonstrated clinically-acceptable results.

• Journal of Digital Convergence
• /
• v.19 no.9
• /
• pp.283-288
• /
• 2021

Due to the 4th Industrial Revolution and the Digital Revolution, many changes are being made in the manufacturing method and structure in the field of plastic arts and crafts. Therefore, in this study, we tried to present a new work method suitable for this era by effectively utilizing the digital technology called 3D printer. For this study, first of all, the theoretical background of 3D printing technology was understood, and prior studies on the use cases of 3D printing technology were summarized. Based on this, three types of craft molds were produced using a 3D printer. As a result of the study, there were characteristics that appear respectively depending on the thickness or overlapping of the craft molds using 3D printing technology. First, in the case of the thickness of the craft molds, the thinner the strength, the weaker the strength, but there was an advantage in that it was easier to take out the contents of the molds. However, it was determined that the thick craft molds was stable to contain the dense and heavy material. Second, in the case of overlapping of craft molds, the advantages of both thin and thick molds were obtained as a result of using a double-layered molds. However, there was a disadvantage that the surface of the contents taken out was not smooth, so that post-processing was necessary. In future research, I hope to deal with the material of the filament used in 3D printers.

• Journal of Technologic Dentistry
• /
• v.41 no.4
• /
• pp.255-262
• /
• 2019

Purpose: Recently, the production technology of dental prosthesis using 3D Printer workpeices has been developed. However, the lack of information on the work processes and casting techniques of materials for 3D printing casting is expected to require research. Therefore, in this study, we intend to cast a Dental DLP 3D Printer workpiece, which is being commercialized, to identify its appearance and internal clearance, and to observe its castability. Methods: Castability of the 3D Printer workpiece was evaluated. The specimen is prepared in a cylindrical shape and in a 1 mm thick coping shape. The control specimen is made of wax and the experimental specimen is made of resin using two types of 3D printers. After casting, the appearance of the casting body was observed and the internal clearance of the coping was measured. Results: RP1 and RP2, cylindrical specimens, were partially cast or fin. When coping-type specimens were measured before casting, the internal clearance of PE2 was more accurate than that of PC and PE1. When coping-type specimens were measured after casting, CE1 was the most accurate in occlusal clearance and CE2n was the most accurate in axial clearance. Conclusion: 1. Exterior observations of the casting body indicated casting defects and fins. 2. Internal clearance observations show that the occlusal clearance of the castings is larger after casting, and the axial clearance of the castings is smaller after casting. 3. It is judged that the RP2 specimen is more likely to be applied for casting than the RP1 specimen.