• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.715-720
• /
• 2003

The chief factors for the penetration and diffusion of chloride ions in concrete are water-cement ratio(W/C), aging, curing conditions, chloride ions concentration of given environment., wet and dry conditions and etc. In this study, of these factors effect of curing conditions such as standard and outdoor curing on the characteristics of chloride ions diffusion in concrete were researched when environmental factors for the penetration and diffusion of chloride ions were constant. For this purpose, the voltages passing through the diffusion cell were measured by using accelerated test method using potential difference, and then diffusion coefficients of chloride ions by using Andrade's method were estimated for 44%, 49.5% and 60% of w/c, respectively. As a result., according to curing conditions correlation among diffusion coefficients of chloride ions, W/C and aging were concluded through multiple regression model.

• Transactions of Materials Processing
• /
• v.22 no.5
• /
• pp.269-274
• /
• 2013

Experiments and numerical simulations of the incremental upsetting test were carried out to investigate void closure behavior and mechanical characteristic of a 1.5wt%C ultra-high carbon steel. The experimental results showed that the voids become quickly smaller as the reduction ratio increases. The simulation results confirmed this behavior and indicated that the voids were completely closed at a reduction ratio of about 40~45% during incremental upsetting. After the completion of the incremental upsetting tests, the process of diffusion bonding was employed to heal the closed voids in the deformed specimens. To check the appropriate temperature for diffusion bonding, deformed specimens were kept at 800, 900, 1000 and $1100^{\circ}C$ for an hour. In order to investigate the effect of holding time for diffusion bonding at $1100^{\circ}C$, specimens were kept at 10, 20, 30, 40, 50 and 60minutes in the furnace. A distinction between closed and healed voids was clearly established using microstructural observations. In addition, subsequent tensile tests demonstrated that complete healing of a closed void was achieved for diffusion bonding temperatures in the range $900{\sim}1100^{\circ}C$ with a holding time larger than 1 hour.

• Journal of Welding and Joining
• /
• v.22 no.1
• /
• pp.77-82
• /
• 2004

The effect of bonding condition on tensile properties of joints diffusion bonded spheroidal graphite cast iron, FCD60 to Cr-Mo steel, SCM 440 was investigated. Diffusion bonding was performed with various temperatures, holding times, pressures and atmospheres. All tensile specimens were fractured at the bonding interface. The tensile strength and elongation was increased with increasing bonding temperature. Especially, tensile strength of joints bonded at 1123K was higher than that of a raw material, FCD60, and tensile strength of joints bonded at 1173K was equal to that of a raw material, SCM440, but elongation of all joints was lower than those of raw materials. There was little the effect of holding time on the tensile properties. In comparison with bonding atmosphere, the difference of tensile strength was not observed, but elongation of joint bonded at vacuum(6.7mPa and 67mPa) was higher than that of Ar gas. Higher the degee of vacuum, elongation increased. Tensile properties of diffusion bonds depended on microstructures of cast iron at the interface and void ratio. Microstructures of cast iron at interface changed with temperature, because decarburizing and interdiffusion at the interface occurs and transformation of austenite-1 ferrite + graphite occurs on the cooling process. The void ratio decreased with increasing temperature, especially, effected on the elongation.

• Journal of Biomedical Engineering Research
• /
• v.29 no.2
• /
• pp.114-121
• /
• 2008

Within 2 to 5 months after stroke, patients recover variable degrees of function, depending on the initial deficit. An impaired hand function is one of the most serious disability in chronic stroke patients. Therefore, to evaluate the extent of motor dysfunction in the hemiplegic hand is important in stroke rehabilitation. In this paper, motor recoveries in 8 chronic stroke patients with Fugl-Meyer (FM) and white matter changes before and after the training program with a designed bilateral symmetrical arm trainer (BSAT) system were examined. The training was performed at 1 hr/day, 5 days/week during 6weeks. In all patients, FM was significantly improved after the 6-week training. Diffusion tensor imaging (DTI) results showed that tractional anisotropy ratio (FAR) and fiber tracking ratio (FTR) in the posterior internal capsule were significantly increased after the training. It seemed that the cortical reorganization was induced by the 6 week training with the BSAT. In all parameters proposed this study, a significant correlation was found between these parameters (FAR and FTR) and motor recoveries. This study demonstrated that DTI technique could be useful in predicting motor recovery in chronic hemiparetic patients.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.717-722
• /
• 2003

The aspect ratio is the main parameter which governs the outer flow pattern and nozzle performance. And in this study, some flow characteristics with the variation of nozzle aspect ratios such as mean pressure distributions along the center line of the outer flow, flow coefficients and the diffusion angles have been experimentally investigated. Through the experimental analysis, the higher aspect ratio was known to decrease the jet kinetic energy because of the friction losses at the outer of nozzle. As the result, it is found that the nozzle performance depends mainly on the aspect ratio of nozzle.

• Journal of Power System Engineering
• /
• v.7 no.3
• /
• pp.12-17
• /
• 2003

The purpose of this study is to observe the purification characteristics of NOx, CO and HC in various catalysts and excess air ratio conditions. For this purpose, we installed various catalysts on the back stream of the coaxial diffusion burner with swirler. As the result, in the case of NOx, Pt-Rh catalyst shows very high value that is more than 90%-conversion efficiency without the relation with the excess air ratio. After excess air ratio of ${\alpha}=1.14$, it shows that the conversion efficiencies were more than 80% in the every Pt catalyst in the view of conversion of every exhaust with changing of the excess air ratio.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.673-678
• /
• 2002

There are various methods for the electrochemical techniques to estimate diffusion coefficient of chloride ions in concrete, such as ASTM C 1202 test method, Andrade's method, Dhir's method, Tang's method, and etc. In the case of estimating diffusion coefficient of chloride ions in concrete by using these methods, applied voltage and resistivity nay exercise some influence on the characteristics of chloride ions diffusion. Thus. in this study, effect of applied voltage and resistivity on the characteristics of chloride ions diffusion in concrete were researched by applying voltage in 12V, 30V, and 60V, and by using resistivity in 0.2Ω and 1.0Ω, respectively. It can be concluded that diffusion coefficient of chloride ions are found to be increasing as the individual applied voltage and resistivity decrease, when water-cement ratio is constant.

• International Journal of Concrete Structures and Materials
• /
• v.4 no.2
• /
• pp.105-108
• /
• 2010

In order to determine the effect of the use of limestone sand on chloride ion ingress in mortar, specimens were cast with two different sands: siliceous sand (used as reference) and limestone crushed sand (used for this study). To compare and assess the resistance of this mortar to chloride penetration, two different diffusions tests were employed: slow migration and rapid migration (AASHTO test). In this study, calculation of the effective diffusion coefficient is proposed using a model based on Nernst. Planck equation. The diffusion coefficients from each sample were compared. The results for all tests show that the diffusion coefficients for siliceous sand mortar are larger than those obtained with limestone sand. It appears also that the diffusion coefficient varies as a function of the W/C ratio.

• Proceedings of the KIEE Conference
• /
• 2006.11a
• /
• pp.192-194
• /
• 2006

In this paper, the situation of energy efficiency standards for motors and diffusion states are analyzed and a new methodology is proposed using diffusion models and learning curves. The existing diffusion models could not explain affects from new appliances' penetration during the diffusion. But a mixed diffusion model with learning curves or learning ratio is studied to explain this penetration.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.50 no.6
• /
• pp.49-60
• /
• 2008

This study were predicted the corrosion threshold reached at steel reinforcement in latex modified concrete(LMC) which were applied the agricultural hydraulic concrete structures. Accelerated testing was accomplished to the evaluate the diffusion coefficient of LMC mix, and the time dependent constants of diffusion. Also, the average chloride diffusion coefficient was estimated. From the average chloride ion diffusion coefficient, the time which critical chloride contents at depth of reinforcement steel was estimated. Test results indicated that the corrosion threshold reached at reinforcement in LMC were effected on the mix proportion factor including cement contents, latex content, and water-cement ratio. Especially, the average chloride diffusion coefficient, the corrosion threshold reached at reinforcement in LMC were affected by the all mix proportion factor.