• The Journal of the Korea Contents Association
• /
• v.7 no.12
• /
• pp.254-261
• /
• 2007

In this paper, we propose a blind equalization method for advanced terrestrial digital multimedia broadcasting (AT-DMB) systems which use hierarchical modulation. The AT-DMB system adopts hierarchical 16-ary quadrature amplitude modulation (16-QAM) to ensure backward-compatibly with the differential quadrature phase shift keying (DQPSK) signal of the legacy terrestrial digital multimedia broadcasting (T-DMB) systems and to support higher transmission rate. Due to the hierarchical modulation, the conventional T-DMB signal and the additional signal have different error rate at same signal to noise ratio (SNR). By weighting the decided symbols differently according to the reliability of the symbols, i.e., high priority symbol with low error rate and low priority symbol with high error rate, we can improve the channel estimation accuracy. In this paper, we analyze SNR loss by hierarchical modulation and confirm it through simulations. Moreover, through simulations, we verify that the proposed weighting method improve BER compared to the no-weighting method.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.4
• /
• pp.315-324
• /
• 2004

In eddy current testing(ECT), differential probes have been frequently used since they .an reduce the number of parameters that influence ECT signals. However, differential signal is actually the difference of the two coils' impedance so that signal prediction and interpretation are not easy, On the other hand, absolute coil signal is rather straightforward to predict and analyze. Therefore, combined use of the two types of signals would increase the test reliability. In this paper, absolute coil signals from Inconel plate and tubes are predicted by the finite element analysis and efforts of lift-off, fill-factor, conductivity, operating frequency, test specimen thickness, inner diameter defects, and outer diameter defects are investigated. As a result, various impedance plane diagrams are drawn and analyzed. Significant practical knowldege about absolute signals is accumulated and similar characteristics of the two types of signal could be understood. Finally, slope angle versus defect depth calibration corves are prepared for three different frequencies.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.1
• /
• pp.301-306
• /
• 2014

We proposed a new PCB-type 'common-mode current($I_c$) and differential-mode current($I_d$) detector' working for fast detection of $I_c$ and $I_d$ from the differential-mode signaling, with miniaturization effect and possibility of cheaper fabrication. In order to realize this device, we suggest a branch-line-coupler balun having a composite right- and left-handed(CRLH) one-layer microstrip phase-shifting line as compact as roughly ${\lambda}_g/14$. The presented balun obviously is different from the conventional bent-&-folded delay lines or slits on the ground for coupling the lines on the top and bottom dielectrics. As we connect the suggested balun output ports of the differential-mode signal lines via the through-port named U and coupled-port named L, $I_c$ and $I_d$ will appear at port ${\Delta}$ and port ${\Sigma}$ of the present device, in order. The validity of the design scheme is verified by the circuit-and numerical electromagnetic analyses, and the dispersion curve proving the metamaterial characteristics of the geometry. Besides, the examples of the $I_c$ and $I_d$ indicator are observed as the even and odd modes in differential-mode signal feeding. Also, the proposed device is shown to be very compact, compared with the conventional structure.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.440-447
• /
• 2002

This paper considerated about exact flow volume calculation method from factors having an influence on measurement and introduced in anesthesia ventilator realized spirometry system. System used differential pressure sensing method with factors, that is temperature, pressure, gas density, humidity and mucus etc. System optimized for low power system for mobile system. System composed analog interface part, signal processing part, display part. Analog interface part have differential pressure flow sensor and defferential pressure sensor. Signal processing part have AVR processor for low power system display part use serial port (RS232, SPT). so it display at pc monitor or send to anesthesia ventilator. System is stable by linearizing 2th characteristics of flow-differential pressure, auto correction of sensor. Noise reduced by algorithm with analog filter and digital processing. Small, light, low power system is good at mobile system and applied to patient in emergency or mobile. and, System is useful at anesthesia ventilator by using flow sensor.

• International Journal of Advanced Culture Technology
• /
• v.10 no.2
• /
• pp.187-193
• /
• 2022

We is configured the honk changing-status technique that is to meld the square-built blow-shock status of the gleam-differential perception level (BIAL) on the honk perception lineament. The perception level condition by the honk perception lineament system is constituted with the blow-shock system. As to experimentation a ductile-dot of the gleam ductile-dot, we are found of the honk value with ductile-dot by the blow upper shift. The concept of perception level is constituted the reference of gleam-differential level for changing-status signal by the honk shock lineament. Further symbolizing a square-built changing-status of the BIAL, of the average in terms of the blow-shock lineament, and the honk ductile-dot shock that was the honk value of the far changing-status of the Ho-PL-FA-θ_AVG with 15.41±8.63 units, that was the honk value of the convenient changing-status of the Ho-PL-CO-θ_AVG with 8.70±3.06 units, that was the honk value of the flank changing-status of the Ho-PL-HO-θ_AVG with 2.65±1.19 units, that was the honk value of the edge changing-status of the Ho-PL-VI-θ_AVG with 0.51±0.18 units. The blow shock will be to investigate at the square-built ability of the blow-shock lineament with ductile-dot by the honk perception level on the BIAL, that is denote the gleam-differential lineament by the perception level system. We will be possible to curb of a lineament by the differential signal and to employ the honk data of blow shock level by the blow perception system.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.10
• /
• pp.70-78
• /
• 2009

This paper addresses the analysis and the design optimization of differential interconnects for high-speed Low-Voltage Differential Signaling (LVDS) applications. Thanks to the differential transmission and the low voltage swing, LVDS offers high data rates and improved noise immunity with significantly reduced power consumption in data communications, high-resolution display, and flat panel display. We present an improved model and new equations to reduce impedance mismatch and signal degradation in cascaded interconnects using optimization of interconnect design parameters such as trace width, trace height and trace space in differential printed circuit board (FPCB) transmission lines. We have carried out frequency-domain full-wave electromagnetic simulations, and time-domain transient simulations to evaluate the high-frequency characteristics of the differential FPCB interconnects. We believe that the proposed approach is very helpful to optimize high-speed differential FPCB interconnects for LVDS applications.

• Journal of Navigation and Port Research
• /
• v.30 no.2
• /
• pp.167-172
• /
• 2006

In this paper, the issue of blind detection of Alamouti-type differential space-time (ST) ${\pi}/2$-shifted BPSK modulation in static Rayleigh fading channels is considered. We introduce a novel transformation to the received signal from each receiver antenna such that this binary ST modulation, which has a second-order transmit-diversity, is equivalent to QPSK modulation with second-order receive-diversity. The pre-detection combining of the result of transformation allows us to apply a low complexity detection technique specifically designed for receive-diversity, namely, scalar multiple-symbol differential detection (MSDD). With receiver complexity proportional to the observation window length, our receiver can achieve the performance 1.5dB better than that of conventional differential detection ST and 0.5dB worse than that qf a coherent maximum ratio combining receiver (with differential decoding) approximately.

• Journal of Sensor Science and Technology
• /
• v.19 no.5
• /
• pp.391-397
• /
• 2010

This paper proposes a differential structure sensor for detecting Ringer's solution exhaustion, in which three C-type electrodes of 10 mm width are disposed on a ringer hose at a distance of 5 mm each other in the direction of Ringer's solution flow. In the center of middle electrode, two capacitances are formed at the proposed sensor. When ringer hose is filled with Ringer's solution, there is no difference between two capacitances. But capacitance difference exist under the Ringer's solution shortage, because the shortage causes the hose filled with air from the top position electrode. The capacitance difference got to maximum 1.81 pF, when air was filled between top and middle electrode and the last of hose was filled with 10 % dextrose injection Ringer's solution. The capacitance difference varied with hose-wraparound coverage of electrodes as well as the width of them. For hose-wraparound electrode coverage of 90 % and 70 %, the maximum capacitance difference was 1.81 pF and 1.56 pF, respectively. A differential charge amplifier converted the capacitance difference to electric signal, and minimized electrodes' adhering problem and external noise coupling problem.

• Nuclear Engineering and Technology
• /
• v.56 no.4
• /
• pp.1532-1537
• /
• 2024

Time-of-flight (TOF) PET detectors with fast-rise-time scintillators and fast-single photon time resolution silicon photomultiplier (SiPM) have been developed to improve the coincidence timing resolution (CTR) to sub-100 ps. The CTR can be further improved with an optimal bandwidth and minimized electronic noise in the readout circuit and this helps reduce the distortion of the fast signals generated from the TOF-PET detector. The purpose of this study was to develop an ultra-high frequency and fully-differential (UF-FD) readout circuit that minimizes distortion in the fast signals produced using TOF-PET detectors, and suppresses the impact of the electronic noise generated from the detector and front-end readout circuits. The proposed UF-FD readout circuit is composed of two differential amplifiers (time) and a current feedback operational amplifier (energy). The ultra-high frequency differential (7 GHz) amplifiers can reduce the common ground noise in the fully-differential mode and minimize the distortion in the fast signal. The CTR and energy resolution were measured to evaluate the performance of the UF-FD readout circuit. These results were compared with those obtained from a high-frequency and single ended readout circuit. The experiment results indicated that the UF-FD readout circuit proposed in this study could substantially improve the best achievable CTR of TOF-PET detectors.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.53-55
• /
• 2001

A dual probe laser Doppler vibrometer (LDV) that has one laser source and provides two independent object beams has been developed for the first time. An electronic circuit that converts light signal to electronic signal has been also developed using phase locked loop(PLL). It was found that this types of dual probe LDV can be used in differential mode and self-vibration compensation mode.