• Journal of Korean Society for Atmospheric Environment
• /
• v.22 no.5
• /
• pp.590-603
• /
• 2006

Size-and time-resolved aerosol samples were collected using an eight-stage Davis rotating unit for monitoring (DRUM) sampler from 23 March to 29 April 2001 at Gosan, Jeju Island, Korea, which is one of the super sites of Asia-Pacific Regional Aerosol Characterization Experiment(ACE-Asia). These samples were analyzed using synchrotron X-ray fluorescence for 3-hr average concentrations of 19 elements including Al, Si, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Br, Rb, and Pb. The size-resolved data sets were then analyzed using the positive matrix factorization(PMF) technique to identify possible sources and estimate their contributions to particulate matter mass. PMF analysis uses the uncertainty of the measured data to provide an optimal weighting. Twelve sources were resolved in eight size ranges($0.09{\sim}12{\mu}m$) and included continental soil, local soil, sea salt, biomass/biofuel burning, coal combustion, oil combustion, municipal incineration, nonferrous metal source, ferrous metal source, gasoline vehicle, diesel vehicle, and volcanic emission. The PMF result of size-resolved source contributions showed that natural sources represented by local soil, sea salt, continental soil, and volcanic emission contributed about 79% to the predicted primary particulate matter(PM) mass in the coarse size range ($1.15{\sim}12{\mu}m$) while anthropogenic sources such as coal combustion and biomass/biofuel burning contributed about 58% in the fine size range($0.56{\sim}2.5{\mu}m$). The diesel vehicle source contributed mostly in ultra-fine size range($0.09{\sim}0.56{\mu}m$) and was responsible for about 56% of the primary PM mass.

• Journal of Life Science
• /
• v.17 no.2 s.82
• /
• pp.248-253
• /
• 2007

This research investigated whether exposure of diesel exhaust particulate (DEP) and particulate matter (PM) effects on airway remodeling in asthma induced Balb/c and IL-10 knock out (KO) mouse. Mice were sensitized with intraperitoneal injection with ovalbumin, followed by challenges with intranasal ovalbumin. After that mice placed in inhalation chamber and exposed to DEP and $PM(10\;mg/m^3)$. The evidence of airway remodeling was assessed by masson's trichrome staining and PAS staining. The stainability of masson's trichrome and PAS reaction were increased in asthma-induced Baltic mice groups compared with control mice groups. More intensive stainability for masson's trichrome and PAS were appeared in the asthma-induced DEP and PM-exposed groups than asthama-induced groups. But, not significantly increased subepithelial fibrosis and the nember of goblet cell hyperplasia in asthma-induced IL-10 KO mice groups and asthma-induced+DEP and PM-exposed IL-10 KO mice than IL-10 KO mice groups. These results indirectly suggesting that exposure to DEP and PM in asthmatic patients might be aggravate clinical symptoms and IL-10 which seems to play a central role in allergic asthma. In conclusion, DEP and PM exposure might have additive effects on the ovalbumin- induced asthma in a murine model.

• Journal of Korea Port Economic Association
• /
• v.36 no.3
• /
• pp.21-38
• /
• 2020

Currently, in-port emissions are a serious problem in port cities. However, emissions, especially non-greenhouse gases, from the operation of cargo handling equipment (CHE) have received significant attention from scientific circles. This study estimates the amount of emissions from on-land port diesel-powered CHE in the Port of Incheon. With real-time activity data provided by handling equipment operating companies, this research applies an activity-based approach to capture an up-to-date and reliable diesel-powered CHE emissions inventory during 2017. As a result, 105.6 tons of carbon monoxide (CO), 243.2 tons of nitrogen oxide (NOx), 0.005 tons of sulfur oxide (Sox), 22.8 tons of particulate matter (PM), 26.0 tons of volatile organic compounds (VOCs), and 0.2 tons of ammonia (NH3) were released from the landside CHE operation. CO and NOx emissions are the two primary air pollutants from the CHE operation in the Port of Incheon, contributing 87.71% of the total amount of emissions. Cranes, forklifts, tractors, and loaders are the four major sources of pollution in the Port of Incheon, contributing 84.79% of the total in-port CHE emissions. Backward diesel-powered machines equipped in these CHE are identified as a key cause of pollution. Therefore, this estimation emphasizes the significant contribution of diesel CHE to port air pollution and suggests the following green policies should be applied: (1) replacement of old diesel powered CHE by new liquefied natural gas and electric equipment; (2) the use of NOx reduction after-treatment technologies, such as selective catalytic reduction in local ports. In addition, a systematic official national emission inventory preparation method and consecutive annual in-port CHE emission inventories are recommended to compare and evaluate the effectiveness of green policies conducted in the future.

• Korean Journal of Materials Research
• /
• v.17 no.7
• /
• pp.382-385
• /
• 2007

[ $LaFeO_3$ ] powders were prepared as the oxidation catalyst materials to reduce the emission of particulate matters from diesel engine and their catalytic effects on the oxidation of carbon were investigated. Solution combustion method was employed for the powder synthesis, which uses highly exothermic and selfsustaining reactions. In this study $LaFeO_3$ powders were synthesized at $400^{\circ}C$ as varying the ratio ($\Phi$) of fuel (citric acid) and oxidizer (metal nitrate), and their phase and carbon ignition property were examined. As $\Phi$ decreases, the crystallinity of synthesized $LaFeO_3$ powders enhanced. By calcining at $700^{\circ}C$, all the powders synthesized at various $\Phi$ fully crystallized. The calcined $LaFeO_3$ powders showed carbon ignition temperature as low as $501{\sim}530^{\circ}C$, which implied the decrease of the ignition temperature by $120{\sim}150^{\circ}C$.

• Journal of Environmental Health Sciences
• /
• v.26 no.2
• /
• pp.34-40
• /
• 2000

The purpose of this study was to investigate the seasonal variation of PAHs and to estimate their source characteristics in Taegu area. To do this, four sampling sites were selected to represent an industrial, a traffic, a traffic & residential, and a residential area in Taegu. Total of 72 samples had been collected from January, 1999 to September, 1999 on glass micro fiber filters by high volume air sampler. The PAHs in the total suspended particulate were extracted by a soxhlet process with dichloromethane and analyzed by GC/MSD, GC/FID. A statistical analysis was performed for the PAHs data set using a principal component analysis to derive important factor inherent in the interactions among the variables. The specific conclusions of this research are: 1) There was a significant seasonal and local variation in the atmospheric concentration of PAHs. The seasonal variation is winter>spring>Fall>summer, and the local variation is industrial>traffic>graffic & residential>residential area. 2) To evaluate the correlation between a measured PAHs and other affecting factors such as air pollutant concentration and meterological data, statistical analysis was performed. PAHs and other affecting factors such as air pollutant concentration and meterological data, statistical analysis was performed. PAHs have negative correlation with temperature (r=-0.593, p<0.05), radiation(r=-0.535, p<0.05), and O3(r=-0.719, p<0.05), but have positive correlation with NO(r=0.615, p<0.05) 3)Finally, multivariate analysis was performed for the PAHs dat set to identify and to estimate the source contributions of PAHs. According to results of statistical analysis, it could be identifies as three factors such as vehicular/gasoline, vehicular/diesel, and combustion in Taegu area.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.1
• /
• pp.93-101
• /
• 2006

This research makes a new attempt to apply the activated seawater by electrolysis in the development of two-stage wet scrubber system to control the exhaust gas of large marine diesel engines. First, with using only seawater that is naturally alkaline (pH typically around 8.1). the $SO_2\;and\;SO_3$ are absorbed by relatively high solubility compared to other components of exhaust pollutants, and PM (Particulate Matter) is removed through direct contact with sprayed seawater droplets. Besides, the electrolyzed alkaline seawater by electrolysis, which contains mainly NaOH together with alkali metal ions $(i.e.\;Na^+,\;Mg^{2+},\;Ca^{2+})$, is used as the absorption medium of NOx and $CO_2$. Especially, to increase NOx absorption rate into the alkaline seawater. nitric oxide (NO) is adequately oxidized to nitrogen dioxide $(NO_2)$ in the acidic seawater, which means both volume fractions are adjusted to identical proportion. The results found that the strong acidic seawater was a valid oxidizer from NO to $NO_2$ and the strong alkaline seawater was effective in $CO_2$ absorption In the scrubber test, the SOx reduction of nearly $100\%$ could be achieved and also led to a sufficientPM reduction. Hence, the author believes that applying seawater and its electrolyte would bring the marine air pollution control system to an economical measure. Additionally it is well known that NOx and SOx concentration has a considerable influence on the $N_2O$ emission of green house gas. Although the $N_2O$ concentration exhausted from diesel engines is not as high, the green house gas effect is around 300 times greater than an equivalent volume of $CO_2$. Therefore, we investigated the $N_2O$ removal efficiency with using the electrolyzed seawater too. Finally this research would also plan to treat the effluent by applying electro-dialysis and electro-flotation technique s in the future.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.128-136
• /
• 2007

It is well known that two representative methods satisfy EURO-IV regulation from EURO-III. The first method is to achieve the regulation through the reduction of NOx in an engine by utilizing relatively high EGR rate and the elimination of subsequently increased PM by DPF. However, it results in the deterioration of fuel economy due to relatively high EGR rate. The second is to use the high combustion strategy to reduce PM emission by high oxidation rate and trap the high NOx emissions with DeNOx catalysts such as Urea-SCR. While it has good fuel economy relative to the first method mentioned above, its infrastructure is demanded. In this paper, the number distribution of nano PM has been evaluated by Electrical Low Pressure Impactor(ELPI) and CPC in case of Urea-SCR system in second method. From the results, the particle number was increased slightly in proportion to the amount of urea injection on Fine Particle Region, whether AOC is used or not. Especially, in case of different urea injection pressure, the trends of increasing was distinguished from low and high injection pressure. As low injection pressure, the particle number was increased largely in accordance with the amount of injected urea solution on Fine Particle Region. But Nano Particle Region was not. The other side, in case of high pressure, increasing rate of particle number was larger than low pressure injection on Nano Particle Region. From the results, the reason of particle number increase due to urea injection is supposed that new products are composited from HCNO, sulfate, NH3 on urea decomposition process.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.3
• /
• pp.83-89
• /
• 2011

Diesel engines can produce higher fuel efficiency and lower $CO_2$ emission, they are subject to ever more stringent emission regulation. However, there are two major emission concerns fo diesel engines like such as particulate matter (PM) and nitrogen oxides (NOx). Moreover, it is not easy to satisfy the regulations on the emission of NOx and PM, which are getting more strengthened. One of the solutions is to apply the new combustion concept using multistage injection such as HCCI and PCCI. The other solution is to apply after-treatment systems. For example, lean NOx trap catalyst, Urea-SCR and others have various advantages and disadvantages Especially, Urea-SCR system have advantages such as a high conversion efficiency and a wide operation conditions. Hence the key factor to implementation of Urea-SCR technology, good mixing of urea(Ammonia) and gas, reducing Ammonia slip. Urea mixer components are required to facilitate evaporation and mixing because the liquid state of urea poses significant barriers for evaporation, and the distance to mixer is the most critical that affect mixer performance. In this study, to find out the distance from injector to mixer and simulation factor, a laser diagnostics and high speed camera are used to analyze urea injector spray characteristics and to present a distribution of urea solution in transparent manifold In addition, Droplet Uniformity Index is calculated from the acquired images by using image processing method to clarify the distribution of spray.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.147-156
• /
• 2008

As the management of fuel efficiency becomes globally reinforced in attempts to find an environment-friendly vehicle that will operate against global warming, the interest in and the demand for the type of vehicle with a high-efficiency diesel engine using light oil. However, it also emits a greater amount of PM (particulate matter) and NOx than emissions from vehicles using other types of fuels. Therefore, the DME (Dimethyl Ether), an oxygen containing fuel draws attention as an alternative fuel for light oil that can be used for diesel engines since it generates very little smoke. But to develop and compare performance of an electric controlled common-rail DME engine, engine tests requires optimized injection conditions at required engine RPM and engine torque. These injection conditions cannot be set freely and the data configuration through the experimentally repeated application requires much time as well as a significant amount of errors and effort. The object of this study is to configure the basic injection map using the results of the DME engine experiments performed so far. For this, in this study, the functionalization of the required equations were performed along with the basic review of the factors that had influence on the data map. Through this, the information on the injection pressure, injection amount, injection duration, injection timing, etc. under certain operation condition could be obtained.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.162-170
• /
• 2007

Currently, due to the serious world-wide air pollution by substances emitted from vehicles, emission control is enforced more firmly and it is expected that the regulation requirements for emission will become more severe. Anew concept combustion technology that can reduce the NOx and PM in relation to combustion is urgently required. Due to such social requirement, technologically advanced countries are making efforts to develop an environment-friendly vehicle engine at the nation-wide level in order to respond to the reinforced emission control. As a core combustion technology among new combustion technologies for the next generation engine, the homogeneous charge compression ignition (HCCI) is expanding its application range by adopting multiple combustion mode, catalyst, direct fuel injection and partially premixed combustion. This study used a 2-staged injection method in order to apply the HCCI combustion method without significantly altering engine specifications in the aspect of multiple combustion mode and practicality by referring to the results of studies on the HCCI engine. And it is investigated that the effects of the engine rpm and load(or A/F) to emission characteristics.