• Journal of ILASS-Korea
• /
• v.16 no.3
• /
• pp.119-125
• /
• 2011

Due to the oxygen contents in biodiesel, application of the fuel to compression ignition engines has significant advantages in terms of lowering PM formation in the combustion chamber. In recent days, considerable studies have been performed to extend the low temperature combustion regime in diesel engines by applying biodiesel fuel. In this work, low temperature combustion characteristics of biodiesel blends in dilution controlled regime were investigated at a fixed engine operating condition in a single cylinder diesel engine, and the comparisons of engine performances and emission characteristics between biodiesel and conventional diesel fuel were carried out. Results show that low temperature combustion can be achieved at $O_2$ concentration of around 7~8% for both biodiesel and diesel fuels. Especially, by use of biodiesel, noticeable reduction (maximum 50% of smoke was observed at low and middle loads compared to conventional diesel fuel. In addition, THC(total hydrocarbon) and CO(Carbon monoxide) emissions decreased by substantial amounts for biodiesel fuel. Results also indicate that even though about 10% loss of engine power as well as 14% increase of fuel consumption rate was observed due to lower LHV(lower heating value) of biodiesel, thermal efficiencies for biodiesel fuel were slightly elevated because of power recovery phenomenon.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05a
• /
• pp.587-591
• /
• 1997

The DGs (Diesel Generators) in NPP (Nuclear Power Plant) has been used for the emergency electric power source to shut down the nuclear reactor safely in case of station blackout. The RCM (Reliability Centered Maintenance) has been applied to DGs for increasing the safety of NPP. The structured defects of DG were not remedied by the improvement of maintenance method. As the first stage of RCM, to find the structured defects, its failure modes were searched and analyzed through the ten year maintenance information. The structured defects such as the air compressor, the lubricating oil pressure, and the insufficient load were the root causes of main failures. The air reservoir reinstallation, the lubricating oil tube modification, the load bank installation, and the qualitative instrumentation were the solutions for the hardware oriented RCM of DGs. There remains the software oriented RCM such as the rejection of useless maintenance, the preventive maintenance, the database of maintenance information, and the predictive maintenance.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.27 no.1
• /
• pp.14-19
• /
• 2017

Fuel oil consumption cost varies depending on every ship operation and this roughly amounts to 70 % of shipping companies' total revenue. As such, efforts towards improved fuel economy are being pursued. An annual 1 % reduction in fuel consumption is perceived to result in saving tens million US dollars on the global fleet operation. One approach is the application of power take-off configurations which are seen to increase fuel oil economy and are suitable for power generation. In this study, the dynamic properties of a shaft generator coupled on a 10S90ME main engine of an 18 600 TEU container vessel is presented. The vibratory torque and angular velocity variation was examined through theoretical analysis and actual vibration measurement. The result of the study suggests a review on existing classification rules for generator design and the lowering of vibratory torque and angular velocity variation guideline.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.3
• /
• pp.528-539
• /
• 2013

Biodiesel is one of the most important renewable energy, since it is one of the most important alternative and eco-friendly energy source compared to fossil energy, especially for diesel engineequipped vehicles. It is now coming up for preparation of biodiesel as the alternative that applies the hetrogeneous catalyst, super critical state and various methods used in order to reduce the stages of the processes be converted and separation stages started from oil and fat which are originated from animals and wastes, and those new methods bring eco-friendly as well, though some of those are stand on research step so far. It is necessary that nation provides the tax exemption program for the supplier and strengthen the research system for the farming crops relate to fat and oil. It can improve the development of biodiesel which sustains stability against oxidation and keeps good mobility over the low temperatures in the winter season by new additives and develops new processes to show good harmony with diesel engine.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.6
• /
• pp.505-509
• /
• 2020

The development of diesel power generation is predominantly geared toward island areas or ships because diesel exhibits weak scale-merit characteristics and power quality problems, which are associated with environmental pollution. However, a new energy paradigm, distribution energy resource (DER), has been emerging as a renewable energy source due to the existing structural problems in waste disposal and complex factors such as the conversion technology of waste emulsified oil (WDF). By combining extended producer responsibility (EPR) support and renewable energy certificates (REC), including waste energy REC 0.25 for other bioenergy and REC 1.0 for power transactions, an adequate profit model can be built through self-energetic power generation, thereby drawing keen attention from related industries. Therefore, if WDF is used appropriately as a high-quality engine fuel, it can lead to the development of various fields such as novel renewable energy sectors, waste management, and EPR-related industries. This study is intended to produce WDF using plastic waste by using it as engine-generator fuel. Moreover, we investigate ways to improve the quality and suitability of WDF as an engine fuel.

• Journal of Internet of Things and Convergence
• /
• v.7 no.3
• /
• pp.75-80
• /
• 2021

Since the optimization of the diesel engine for the ship cannot satisfy the NOx emission limit by the method of reducing the NOx emission, it is necessary to reduce the NOx by post-processing the exhaust gas. In this study, we will review the feasibility of designing a binary nozzle and mixing chamber duct for effectively converting the number of elements into NH3 in the oil burner for the SCR catalyst unit integrated duct in the ship under development through the computational heat flow analysis for the velocity distribution and temperature distribution.

• Tribology and Lubricants
• /
• v.24 no.4
• /
• pp.196-204
• /
• 2008

In this study, the pressure distributions on the oil film of piston pin bearings are found by two-dimensional lubrication analysis in order to help the optimum design of the bearings of piston pin. The lubrication analysis is carried out together with an equation related with the oil pressure-viscosity index. The oil film pressure distribution is used as an input data for pressure boundary conditions at the piston pin-boss surface. Finally, the piston pin-boss stress distribution coupled with the thermal stress is calculated, and then compared with the results of the stress analysis which is not counted with the oil film pressure boundary condition.

• Tribology and Lubricants
• /
• v.34 no.4
• /
• pp.160-167
• /
• 2018

Vegetable oils can contribute to the goal of energy independence and security owing to their naturally renewable resources. One of the representative vegetable oils is biodiesel, which is being used in domestic and European markets as a blended fuel with automotive diesel. Vegetable oils are promising candidates as base fluids to replace petroleum lubricants because of their excellent lubricity and biodegradability. We prepared biodiesel with a purity of 99.9% via the esterification of waste cooking oil. Blended biodiesel and Petro-lube base oil were mixed to produce five types of mixed lubricating oil. We analyzed the various characteristics of the blended biodiesel with Petro-lube base oil for different blending ratios. The lubricity of the vegetable lubricant improves as the content of biodiesel increases. In addition, since zinc dialkyldithiophosphates (ZnDTPs) are widely used as multifunctional additives in petroleum-based lubricants, we optimized the blending ratio for lubricity, oxidation stability, and shear stability by adding ZnDTP as a performance additive to improve the biodiesel properties, such as oxidation stability and hydrolysis. The optimized lubricants improve by approximately 25% in lubricity and by 20 times in oxidation stability and shear stability after the addition of ZnDTP.

• KSBB Journal
• /
• v.24 no.1
• /
• pp.89-95
• /
• 2009

Biodiesel (fatty acid alkyl esters), which is produced from sustainable resources such as vegetable oil, animal fat and waste oils, have used to as substitutes for petro-diesel. In this study, we investigate the performance of 30 L and 300 L pilot-scale biodiesel production system using alkali-catalyst transesterification from soybean oil and rapeseed oil produced at Jeju island in Korea. The 30 L-scale biodiesel production was performed to in the condition of reaction temperature $65^{\circ}C$, catalyst amount 1% (w/w) and oil to methanol molar ratio 1 : 8. At that reaction condition, the fatty acid methyl ester contents of product are above 98% within reaction time 30 min. Also, the conversion yield of over 98% was obtained in 300 L-scale biodiesel production system using rapeseed oil and soybean oil. The quality of biodiesel produced from reaction system was satisfied to recommended quality standard of Korea. Our results may provide useful information with regard to the scale-up of more economic and efficient biodiesel production process.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.166-170
• /
• 2014

In this paper, we investigate the electric and magnetic properties of the engine oil, and estimate its changing time in transport truck. The four diesel trucks are selected, and the capacitance and inductance are investigated with parallel capacitor and induction coil, respectively. The measured capacitance gradually increases up to 10,000~14,000 km due to the activation of antioxidant, and then decreasing phenomena happen. The inductance decreases and the saturation began in 10,000~14,000 km range. Although the behavior of inductance is different from that of capacitance, but changing points are similar. From those results, we can estimate the changing time of engine oil is around 10,000~14,000 km and the inductance can be used for monitoring of engine oil in transport trucks.