• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.3
• /
• pp.62-67
• /
• 2009

In this study, the potential possibility of biodiesel fuel was investigated as an alternative fuel for a naturally aspirated indirect injection diesel engine. The smoke emission of biodiesel fuel was reduced remarkably in comparison with diesel fuel, that is, it was reduced approximately 36% at 2000rpm, full load condition. And, power, torque and brake specific energy consumption showed no significant differences. However, NOx emission of biodiesel fuel was increased compared with commercial diesel fuel. Also, the effects of exhaust gas recirculation(EGR) to reduce the NOx emission has been investigated. It was found that simultaneous reduction of smoke and NOx was achieved with biodiesel fuel(20vol-%) and cooled EGR method$(10{\sim}15%)$.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.74-80
• /
• 2005

It becomes necessary for engine manufactures to verify whether lots of engines on test bed during shop test are in compliance with NOx Technical Code for marine diesel engines more efficiently on the basis of engine group test concept which contains parent engine and member engines since all the engines are not needed to take NOx measurement. In addition, it becomes more obliged to consider parameters which affect NOx emission level and describe these parameters in NOx technical file as engine information and settings to define engine operation range with tolerance to make sure the engines are still in compliance with NOx emission limit on board after shop test. During preparation of engine group test for 4-stroke marine diesel engines, we evaluated NOx emission value under different engine operating conditions and found that there are certain parameters, for example, Charge air temperature and Max. cylinder pressure which have influence on NOx emission level. The NOx emission shall be satisfied with NOx technical code by means of controlling such parameters.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.3007-3012
• /
• 2008

Multidimensional simulation has been carried out to be clear the role of initial combustion in a marine diesel engines on reduction of NOx and soot emissions by different pilot injection condition. Pilot injection can shorten the ignition delay, thus it reduces the premixed combustion phase. Since most NOx is formed during premixed combustion, pilot injections is one of reliable strategies to reduce the NOx. The formation of NOx consists of that formed by pilot injection and that formed by main injection. The result explains that 25-3-75 among the pilot injection conditions is effective to reduce the NOx, due to optimal combination pilot injection with main injection. The purpose of this study is to explain the characteristics of combustion with pilot injection of the marine diesel engine on reduction of exhaust emissions by examining the combustion process in a cylinder and to explore the formation mechanism of NOx between pilot injection and main injection.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.3
• /
• pp.457-465
• /
• 2004

Environmental protection on the ocean has been interested and nowadays the International Maritime Organization(IMO) has advanced on the prevention of air pollution from ships. This study presents the performance and the emission characteristics of 4 stroke marine diesel engines for generation application in D2 cycle(IMO mode). The effects of important operating parameters, such as intake air pressure. intake air temperature and maximum combustion pressure on NOx emissions were also described. Emissions measurement and calculation are processed according to IMO Technical Code. The results show that the maximum combustion pressure by fuel injection timing control and intake air temperature has strong influence on NOx emission production. But NOx emission is not affected by intake air pressure and exhaust gas back pressure.

• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.225-230
• /
• 2003

The major purpose of this study is to find the optimized split injection quantities and dwell angles for PM reduction without increasing NOx. The tests were performed on a Common-Rail DI Diesel Engine to obtain optimum injection timing and duration. In this study, total injection quantities were divided into the ratio of 25-75%, 50-50% and 75-25%. NOx and PM were measured on the condition of the same bsfc by increasing dwell angles. It was found that the split injection reduced NOx with dwell angle increase. For 50_50, 75_25% split injection cases, PM was reduced with 10 to 12(CAD) dwell angles. For 25_75% split injection 33% PM reduction was achieved with 8 to 12(CAD) dwell angles.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.2
• /
• pp.248-255
• /
• 2002

Miller cycle was studied and analyzed by engine performance simulation to achieve very low fuel consumption and to meet the IMO NOx regulation on a medium speed diesel engine. Based on the performance simulation results the intake valve closing time for HYUNDAI HiMSEN 6H21/32 engine was set at 0deg.ABDC(After Bottom Dead Center). Also, the simulation results indicated that significant NOx reduction could be achieved with low reduction of fuel consumption. The performance simulation investigated the effect of compression ratio and turbocharger on fuel consumption and NOx concentration in combination with Miller cycle. The results indicated a significant reduction of fuel consumption with keeping NOx concentration. The results of performance simulation were compared with measured data to verify simulation results. The comparison showed the maximum error was 2.34% in exhaust temperature. Also, the experimental result showed that improvement in BSFC(Brake Specific Fuel Consumption) was 5.8g/kwh with keeping NOx level similar to simulation result.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.4
• /
• pp.150-155
• /
• 2012

Lean NOx Trap (LNT) catalysts are capable of reducing exhaust NOx emissions from diesel engines. LNT stores NOx in lean condition and exhausts N2 by reducing NOx in rich condition. NOx reduction characteristic of LNT catalysts using throttle position sensor and fuel injection timing control for light-duty diesel engine was investigated. In contrast to SCR system, LNT catalyst uses diesel fuel in resuctant. Also if the concentration of reductant is exceeded, excessive amount of reductant will slip throughout LNT and cause another emission problem. Thus LNT regeneration with precise engine control established that can make higher NOx conversion efficiency and lower fuel penalty, prevent another emission problem. NOx and reductant concentration were measured by the NOx sensor and Mexa7100D equipped inlet and outlet of catalyst. As a result of engine test, regeneration strategy has reached high of 77.8% NOx conversion efficiency according to engine operation condition. Moreover, we have proved that it is possible to use regeneration strategy of LNT within 5% fuel penalty.

• Journal of Power System Engineering
• /
• v.19 no.1
• /
• pp.56-63
• /
• 2015

In this study, the exhaust characteristics of the diesel engine for the change of the mixing ratio of biodiesel fuel were quantitatively analyzed by using the numerical analysis method. As the fuel used in the experiment, the diesel and biodiesel(waste oil, soybean oil), the mixed fuel BD2(Diesel only), BD3, BD5, BD20, BD50 and BD100 were used. The injection pressure($p_{inj}$) was set to 400bar, 600bar, 800bar, 1000bar and 1200bar as the experimental variable. Also the concept of the standard deviation, Pearson's correlation coefficient and Spearman rank-order correlation coefficient based on the statistics was introduced in order to analyze the exhaust characteristics of the quantitative NOx and Soot according to the injection pressure and the mixing ratio variation of biodiesel blending fuel. It is considered that as a result of studies, for the waste oil, NOx and Soot can be simultaneously reduced through control of the mixing ratio at the regions of $p_{inj}=400bar$ and $p_{inj}=600bar$, and the Soot can be reduced without affecting on the emission of NOx at more than $p_{inj}=800bar$. For the soybean oil, NOx and Soot can be simultaneously reduced at $p_{inj}=400bar$ and the Soot can be reduced without affecting on the emission of NOx at $p_{inj}=600bar$.

• Journal of ILASS-Korea
• /
• v.7 no.1
• /
• pp.7-13
• /
• 2002

This paper is study on simultaneous reduction of NOx and soot for direct injection diesel engine using high and low cetane fuels. The stratified injection system was applied for diesel engine to use high and low cetane fuel. In this study, diesel fuel was used as high cetane fuels, methanol was used as low cetane fuels. Some parts of the injection system, ie. Nozzle holder. delivery vale, was remodeled to inject dual fuel sequentially from one injector. The leak injection quantity ratio of dual fuel was certificated by volumetric ratio at injection quantity experiment. According as concentration of low cetane fuel was varied, combustion experiment was performed using Toroidal and Complex chamber. Also, exhaust gas and fuel consumption were measured at the same time. Simultaneous reduction of NOx and soot was achieved at complex chamber regardless of concentration of low cetane fuel. However, according as concentration of low cetane fuel was increased, THC and CO was increased.

• Journal of Mechanical Science and Technology
• /
• v.15 no.11
• /
• pp.1588-1598
• /
• 2001

The effects of recirculated exhaust gas on the characteristics of NOx and soot emissions under a wide range of engine loads were experimentally investigated by using a four-cycle, four-cylinder, sw irl chamber type, water-cooled diesel engine operating at three engine speeds. The purpose of this study was to develop the EGR-control system for reducing NOx and soot emissions simultaneously in diesel engines. The EGR system is used to reduce NOx emissions, and a novel diesel soot removal device with a cylinder-type scrubber for the experiment system was specially designed and manufactured to reduce soot contents in the recirculated exhaust gas to the intake system of the engine. The experiments were performed at the fixed fuel injection timing of 4$^{\circ}$ ATDC regardless of experimental conditions. It was found that soot emissions in exhaust gases were reduced by 20 to 70% when the scrubber was applied in the range of the experimental conditions, and that NOx emissions decreased markedly, especially at higher loads, while soot emissions increased owing to the decrease in intake and exhaust oxygen concentrations, and the increase in equivalence ratio as the EGR rate is elevated.