• 한국가스학회지
• /
• 제26권3호
• /
• pp.45-53
• /
• 2022

디젤엔진의 배출물 개선을 위해 탄소수가 낮은 천연가스를 혼합하여 사용하는 천연가스-디젤 혼소 연소가 각광받고 있다. 특히 자발화 특성에 차이가 있는 디젤과 천연가스의 특성을 이용한 반응성 제어 압축착화(reactivity controlled compression ignition, RCCI) 연소 전략을 통해 기존 디젤엔진의 효율과 배출가스를 동시에 개선시키는 연구가 활발하게 진행되어 왔다. 상사점보다 앞당겨진 디젤 직접 분사시기 적용을 통해 실린더 전체 영역의 균일 혼합기를 형성하여 전체적으로 희박한 자발화 기반 연소를 달성함으로써 질소산화물 (NOx) 및 입자상물질 (PM) 저감과 제동열효율 개선을 동시에 달성할 수 있다. 하지만 매우 희박한 저부하 영역에서 불완전 연소량이 증가하는 단점이 존재하며, 안정적인 연소 구현을 위해 디젤 분사시기가 민감하게 제어되어야 하는 어려움도 존재한다. 본 연구에서는 앞서 언급된 저부하 영역에서의 천연가스-디젤 혼소 엔진의 효율 및 배기 개선을 확인하고, 동시에 발전용 엔진 구동 영역에서 디젤 분사시기에 따른 연소안정성을 평가하였다. 실험에는 6 L급 상용디젤 엔진이 사용되었으며, 1,800 rpm, 50% 부하 영역 (~50 kW)에서 실험이 진행되었다. 제동효율 및 연소안정성을 개선하기 위한 전략으로 분무 패턴이 다른 2개의 인젝터를 적용하였으며, 천연가스/디젤 비율과 디젤 분사시기를 바꿔가면서 실험이 진행되었다. 실험 결과, 협각 분사가 추가된 수정 인젝터에서 제동 열효율이 증가하는 것을 확인하였다. 또한 연소안정성 및 출력, 그리고 강화된 배기 규제를 고려하였을 때 수정 인젝터의 분무 패턴이 예혼합연소 형성에 적합하였고 이를 통해 질소산화물 배출량을 Tier-V 기준치인 0.4 g/kWh 이하로 저감함으로써 RCCI 연소 가능 영역을 확장할 수 있음을 실험적으로 확인하였다.

• 한국자동차공학회논문집
• /
• 제10권4호
• /
• pp.33-42
• /
• 2002

Recently, our world is faced with very serious and hard problems related to the air pollution due to the exhaust emissions of the diesel engine. In this paper, the effect of oxygen component in fuel on the exhaust emissions has been investigated fur direct injection diesel engine. It was tested to estimate change of engine performance and exhaust emission characteristics for the commercial diesel fuel and oxygenate blended fuel which has three kinds of mixed ratio. And, it was tried to analyze not only total hydrocarbon but individual hydrocarbon components from Cl to C6 in exhaust gas using gas chromatography to seek the reason far remarkable reduction of smoke emission. This study was carried out by comparing the chromatogram with diesel fuel and diesel feel blended DGM(diethylene glycol dimethyl ether) 5%. The results of this study show that individual hydrocarbon(C1∼C6) as well as total hydrocarbon of oxygenated fuel is reduced remarkably than that of diesel fuel.

• 대한기계학회논문집B
• /
• 제27권5호
• /
• pp.589-595
• /
• 2003

DME(Dimethyl ether) is an oxygenated fuel with a octane number higher than that of diesel oil. It meets the ULEV emission regulation and reduces the smoke to almost zero when used in a diesel engine. In the present study, engine performance and exhaust emissions were investigated with a conventional DI diesel engine which has a jerk type injection pump. Test results showed that the power with DME were almost same as that of pure diesel oil, and the brake thermal efficiency increased a little. Also, smoke index from DME engine showed nearly zero level, but NO$_{x}$ was increased compare to diesel oil.

• 한국분무공학회지
• /
• 제16권3호
• /
• pp.152-158
• /
• 2011

Fast pyrolysis of biomass is one of the most promising technologies for converting biomass to liquid fuels. The pyrolysis oil, also known as the bio crude oil (BCO), have been regarded as an alternative fuel for petroleum fuels to be used in diesel engine. However, the use of BCO in diesel engine requires modifications due to low energy density, high water contents, low acidity, and high viscosity of the BCO. One of the easiest way to adopt BCO to diesel engine without modifications is the use of BCO/diesel emulsions. In this study, a diesel engine operated with diesel, bio diesel (BD), and BCO/diesel emulsion was experimentally investigated. Performance and emission characteristics of a diesel engine fuelled by BCO/diesel emulsion were examined. Results showed that stable engine operation was possible with emulsion and engine output power was comparable to diesel and bio diesel operation. Long term validation of adopting BCO in diesel engine is still needed because the oil is acid, with consequent problems of corrosion especially in the injection system.

• Environmental Engineering Research
• /
• 제9권2호
• /
• pp.51-57
• /
• 2004

• 대한기계학회논문집B
• /
• 제41권6호
• /
• pp.397-407
• /
• 2017

본 논문에서는 연비손실 없이 높은 $NO_X$ 저감성능을 보이는 승용 디젤 엔진의 SCR 시스템을 위한 요소수의 분사전략을 제시하였다. 배출되는 $NO_X$량 대비 요소수가 화학량론적 1:1인 피드포워드 분사 전략과 함께 모델기반의 촉매 내 $NH_3$ 흡장률 추정 기법을 통하여 피드백 분사 제어전략을 함께 사용함으로써 과도상태에서 $NO_X$ 저감성능과 $NH_3$ 슬립 성능을 모두 만족시키고자 하였다. 제안된 분사전략을 적용하여 디젤산화촉매기와, 미립자필터가 장착된 2.2L 디젤 엔진을 갖춘 실제 차량에서의 실험을 통하여 제어기의 높은 $NO_X$ 저감률과 낮은 $NH_3$ 슬립 성능을 검증하였다.

• 대한기계학회논문집B
• /
• 제35권2호
• /
• pp.137-143
• /
• 2011

본 연구는 4실린더 커먼레일 디젤엔진에 바이오디젤 혼합 디젤연료를 적용하였을 경우 엔진의 연소특성과 배출물 저감효과를 실험적으로 구한 것이다. 실험 연료는 바이오디젤 20%와 디젤연료 80%(체적분율)를 혼합한 BD20과 저유황디젤연료(ULSD)를 사용하였으며, 연료분사압과 엔진회전수를 변수로하여 실험을 수행하였다. 실험결과 B20과 ULSD 모두 연료분사압력이 증가함에 따라 NOx 배출농도는 증가하고, Soot 배출량은 감소하는 경향을 나타내었다. 특히 BD20의 경우 ULSD와 비교하여 NOx 배출농도는 다소 증가하였으나, Soot 배출량은 현저하게 감소하였다. 또한, 회전속도가 1000rpm에서 2000rpm으로 증가함에 따라 NOx 배출농도는 감소하고, Soot 배출량은 낮은 분사압력에서 현저히 증가하는 경향을 나타내었다.

• 한국자동차공학회논문집
• /
• 제17권1호
• /
• pp.105-113
• /
• 2009

The performance of a direct-injection type diesel engine often depends on the strength of swirl or squish, shape of combustion chamber, the number of nozzle holes, etc. This is of course because the combustion in the cylinder was affected by the mixture formation process. In this paper, combustion process of biodiesel fuel was studied by employing the piston which has several grooves with inclined plane on the piston crown to generate swirl during the compression stroke in the cylinder in order to improve the atomization of high viscosity fuel such as biodiesel fuel and toroidal type piston generally used in high speed diesel engine. To take a photograph of flame, single cylinder, four stroke diesel engine was remodeled into two stroke visible engine and high speed video camera was used. The results obtained are summarized as follows; (1) In the case of toroidal piston, when biodiesel fuel was supplied to plunger type injection system which has very low injection pressure as compared with common-rail injection system, the flame propagation speed was slowed and the maximum combustion pressure became lower. These phenomena became further aggravated as the fuel viscosity gets higher. (2) In the case of swirl groove piston, early stage of combustion such as rapid ignition timing and flame propagation was activated by intensifying the air flow in the cylinder. (3) Combustion process of biodiesel fuel was improved by the reason mentioned in paragraph (2) above. Consequently, the swirl grooves would also function to improve the combustion of high viscosity fuel.

• 한국분무공학회지
• /
• 제23권4호
• /
• pp.192-204
• /
• 2018

In this study, a 3D CFD analysis method for the combustion process was established for a low calorific value syngas-diesel dual-fuel engine operating under very lean fuel-air mixture condition. Also, the accuracy of computational analysis was evaluated by comparing the experimental results with the computed ones. To simulate the combustion for the dual-fuel engine, a new dual-fuel chemical kinetics set was used that was constituted by merging two verified chemical kinetic sets: n-heptane (173 species) for diesel and Gri-mech 3.0 (53 species) for syngas. For dual-fuel mode operations, the early stage of combustion was dominated by the fuel burning inside or near the spray plume. After which, the flame propagated into the syngas in the piston bowl and then proceeded toward the syngas in the squish zone. With the baseline injection system and piston shape, a significant amount of unburned syngas was discharged. To solve this problem, effects of the injection parameters and piston shape on combustion characteristics were analyzed by calculation. The change in injection variables toward increasing the spray plume volume or the penetration length were effective to cause fast burning in the vicinity of TDC by widening the spatial distribution of diesel acting as a seed of auto-ignition. As a result, the unburned syngas fraction was reduced. Changing the piston shape with the shallow depth of the piston bowl and 20% squish area ratio had a significant effect on the combustion pattern and lessened the unburned syngas fraction by half.

• 한국자동차공학회논문집
• /
• 제18권3호
• /
• pp.80-87
• /
• 2010

The purpose of this paper is to analyze the effects of ethanol blending ratio and fuel temperature in diesel-ethanol blended fuel on the spray-atomization characteristics in a high pressure common-rail injection system. In this work, a diesel fuel and three blended fuels were used as test fuels. Blended fuels were made by blending ethanol with a purity 99.9% to diesel fuel, from 0% to 30%. In order to keep diesel-ethanol blending stability, 5% of biodiesel fuel as volumetric ratio was added into test fuels. The fuel temperature was controled in steps with 40K, from 290K to 370K. Macroscopic spray characteristics were investigated by analyzing the spray tip penetration and spray cone angle through spray images obtained from visualization system. In addition, in order to study microscopic spray characteristics of ethanol blended fuels, the droplet diameter, was analyzed using the droplet measuring system. It is revealed that the spray tip penetration is similar regardless of ethanol blending ratio. As ethanol blending ratio is increased, the spray cone angle becomes wider. It is shown that the spray cone angle is affected by low viscosity and density of ethanol. As the fuel temperature increases, the spray tip penetration and spray cone angle become shorter and narrower respectively. The SMD of ethanol blending fuels is smaller than that of diesel fuel because of low viscosity and surface tension of ethanol.