• 한국자동차공학회논문집
• /
• 제6권5호
• /
• pp.75-85
• /
• 1998

This paper presents the procedures and technique of the decision on the decision on the mount in a diesel engine development newly. To assess the vibration chara- cteristics of the engine plus transmission, their inertia moments are calculated for three engine versions. i.e., NA(Naturally Aspirated), TC(Turbocharged) and TCI(Turbocharged and Intercooled). These data are used to determine the mount layout and stiffness values affecting the noise quality of an engine as well as a vehicle. The main purpose of this paper is to design the mount rubber having the optimal stiffness characteristics through the investigation of the calculation results and the mount conditions when an engine is installed in a vehicle using the existing engine mount room. Thus, this paper describes the optimal mount positions, rubber stiffnesses, natural frequency, mode shapes and so on using ADAMS program to apply the newly developed engines to three different vehicles.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 추계학술대회 논문집
• /
• pp.257-261
• /
• 2011

The failures of local structure of marine medium-speed diesel engine occurred in durability test. The vibration response of the whole engine was in an acceptance level, but the local structures were broken. ODS test and vibration measurement were carried out in order to investigate the root cause of durability problem. These tests revealed that the root cause of failures was excessive vibration by $4.5^{th}$ resonance between engine body and local structure. The best solution to reduce the vibration response is to change the type of mount. After a rigid mount was replaced by a flexible mount, maximum vibration level dropped to 72%.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.93-99
• /
• 2012

이 논문은 선박디젤엔진의 진동제어에 적용할 수 있는 MR 유체기반 마운트(MR 마운트)의 최적설계를 제시한다. 이 연구에서는 압착모드, 유동모드, 전단모드를 포함하는 혼합모드가 제안되었고 설계되었다. 효과적인 진동제어를 위하여 요구되는 MR 마운트의 작동 댐핑력을 결정하기 위하여 디젤엔진의 기진력이 분석되었다. 이 분석에서 V-type 엔진이 고려되었으며 피스톤의 토크에서의 속도와 가스압력간의 관계를 유도하였다. 결과적으로 상업적으로 이용 가능한 MR 유체의 장의존적 유동특성과 기진력을 통합함으로써 적절한 MR 마운트의 크기가 설계되었다. 게다가 기하학적 제한조건이 고려된 최대 구동력을 얻기 위해 ANSYS 를 이용하여 최적설계가 수행되었다. 자기밀도분석을 통해 바닥간격과 코일의 반지름과 같은 최적설계변수가 결정되었다.

• 한국소음진동공학회논문집
• /
• 제23권3호
• /
• pp.209-217
• /
• 2013

이 논문은 선박용 디젤엔진의 진동제어에 적용할 수 있는 MR 유체기반 마운트(MR 마운트)의 최적설계를 제시한다. 이 연구에서는 압착모드, 유동모드, 전단모드를 포함하는 혼합모드가 제안되었고 설계되었다. 효과적인 진동제어를 위하여 요구되는 MR 마운트의 작동 댐핑력을 결정하기 위하여 디젤엔진의 기진력이 분석되었다. 이 분석에서 V-type엔진이 고려되었으며 피스톤의 토크에서의 속도와 가스압력간의 관계를 유도하였다. 결과적으로 상업적으로 이용 가능한 MR 유체의 장의존적 유동특성과 기진력을 통합함으로써 적절한 MR 마운트의 크기가 설계되었다. 게다가 기하학적 제한조건이 고려된 최대 구동력을 얻기 위해 ANSYS를 이용하여 최적설계가 수행되었다. 자기밀도분석을 통해 바닥간격과 코일의 반지름과 같은 최적설계변수가 결정되었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.921-924
• /
• 2005

Diesel generator sets with resilient mounts often experience resonances by major excitations which come from diesel engine and their foundation with rigid body modes. Because their natural frequency is determined by moment of inertia and stiffness of resilient mount vibration problems are resolved by changing location and stiffness of resilient mounts. But the calculated natural frequencies are inaccurate due to uncertainty of the inertia and mount stiffness. So this result can be useless on the design stage. In this paper, the stiffness of mount is evaluated on result from mount stiffness test in laboratory and generator set vibration test and a simple calculation method for moment of inertia is proposed. Based on these data, the procedure to select optimized mount stiffness and location on the design stage is set up.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.481-487
• /
• 1997

The development of transportation and construction equipment has required higher engine power and lower operation cost. The sound which the engine emits often degrade the performance of the whole system which adopts that engine. Specially the marine engine requires high restriction on the noise level for the customer's comfort and safety. The noise and vibration of Diesel engine must be carefully considered in the early design step. The double antivibration system is effective to increase the efficiency of antivibration, and the acoustic enclosure for reducing the noise level. 2 DOF model was effective to estimate the antivibration performance, which allows to determine the mass of the engine bed and the specification of the engine mount. The mass distribution of the enclosure system can be considered effectively by using the FEM model. The design contains structurally rigid engine bed by FEM, which is for reducing the influence of the flexible vibration, rubber mount selection as well as the acoustic enclosure design.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.89-92
• /
• 2012

Marine diesel generator(D/G) set which is supported with resilient mounts for vibration isolation has been experienced the resonance problem by the main engine or propeller excitations and rigid body modes. Then the avoidance of resonance is difficult because the several excitations and 6 rigid body modes have to be considered simultaneously. In this paper, stiffness adjustable mounts was developed and proposed to control the natural frequencies of installed D/G set. Operating concept of the mount is that the total stiffness of mount can be changed according to the engagement of secondary rubber element in addition to primary one. The performance of mount was verified with the test rig and actual experiment in D/G set.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 춘계학술대회 논문집
• /
• pp.273-278
• /
• 2013

This paper presents optimal design procedures of mount based on a magnetorheological (MR) fluid to isolate the vibration in heavy diesel engine system. At first, frequency response and force-displacement transmissibility methods are used to get required damping force that is necessary for effective vibration isolation. From this result, a new type of high damping force engine mount is proposed and the governing equation of Bingham plastic behavior of MR fluid in flow path is mathematically derived under cylindrical coordinates. Finally, parametric design optimization featuring finite element is performed using ANSYS software to get the required damping force in MR mount system which can be used to reduce engine vibration. Damping force of the MR mount is then determined as an objective function in this analysis based on ANSYS. Furthermore, Magnetic analysis is then applied in this process.

• 한국소음진동공학회논문집
• /
• 제23권5호
• /
• pp.472-478
• /
• 2013

This paper presents optimal design procedures of mount based on a magnetorheological(MR) fluid to isolate the vibration in heavy diesel engine system. At first, frequency response and force-displacement transmissibility methods are used to get required damping force that is necessary for effective vibration isolation. From this result, a new type of high damping force engine mount is proposed and the governing equation of Bingham plastic behavior of MR fluid in flow path is mathematically derived under cylindrical coordinates. Finally, parametric design optimization featuring finite element is performed using ANSYS software to get the required damping force in MR mount system which can be used to reduce engine vibration. Damping force of the MR mount is then determined as an objective function in this analysis based on ANSYS. Furthermore, Magnetic analysis is then applied in this process.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.399-406
• /
• 2007

Structural vibrations of generator sets with medium speed diesel engine mainly come from the resonance between the excitations of engine and natural modes of system. The countermeasures to reduce the vibration or to avoid the resonance are fairly well known to workers. However these processes which are applied after the completion of system need much time consumption and additional cost. In this paper, the vibration measurement results collected for about 8 years were compiled as Database. Based on the database, the change of vibration was predicted with respect to variation of system such as engine type, generator weight, mount stiffness, and etc. As results of study, this paper presents the anti-vibration design procedures of newly composed generator sets using Database in the initial design stage and their effects.