• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.5
• /
• pp.59-65
• /
• 2014

Diesel engines have the superior combustion efficiency and fuel economy that they are widely used for industry, heavyduty vehicles, etc. However, its exhaust emissions have become the major concerns due to their environmental impacts. Moreover, the depletion of fossil fuels is the main issue. Therefore, it is important to look for alternative sources of energy. Bio-diesel is one of the ideal energy which has proved to be ecofriendly for more than fossil fuels. The experimental tests analysed the engine performance and emission characteristics of a diesel engine using diesel and biodiesel blended of BD25, BD45 and BD65, in order to study the use of clean fuel to meet the increasingly stringent emission regulations. The engine performance was examined by using engine dynamometer while an exhaust gas analyzer was used to examine the emission characteristics. The effect of biodiesel on engine performance were lower to diesel through comparing their HP and torque but fuel consumption was slightly increased because of biodiesel has lower heating value and higher density than diesel. However, due to the better lubricity, the brake thermal efficiency of biodiesel was higher than diesel. The emission characteristics were strongly affected by the blending ratio of diesel and biodiesel. The results showed that the smoke opacity, hydrocarbons (HC) and carbon monoxide (CO) emissions decreased while the nitrogen oxides (NOX) slightly increased.

• Journal of Institute of Convergence Technology
• /
• v.3 no.1
• /
• pp.25-29
• /
• 2013

The purpose of this paper is to determine the fuel change and weight change impact on the fuel economy and emission characteristic of ICE (Internal Combustion Engine) vehicle. According to fuel type, fuel consumption and emission characteristics were measured and fuel used in this paper was gasoline, diesel, and LPG. Four vehicles with different weight were tested and the fuel economy were compared and analyzed by using scatter graph. Test was carried out using chassis dynamometer, CVS (Constant Volume Sampler), and emission measurement system. Diesel vehicle less emited $CO_2$ compared to gasoline and LPG. Even if same $CO_2$ between gasoline and LPG, there are difference fuel economy depending on carbon proportion of specific fuel. The heavier weight of vehicle, the worse of fuel economy and Better fuel economy performance on highway driving mode.

• 한국연소학회:학술대회논문집
• /
• 2001.11a
• /
• pp.185-192
• /
• 2001

In this study the characteristics of E-EGR valve developed by UNICK were analyzed and the feasibility of application to vehicles were evaluated. Smart car(3L/100km, cdi version) and engine which is small-displacement size, 0.8-liter, of diesel passenger car developed from Mercedes-Benz were used for this experiment. It was installed a 3-cylinder turbo-charged light duty diesel engine with an electronic EGR valve. After the analysis and comparison of E-EGR valve performance under test benchs, the estimation of vehicle application was executed through the EGR map and CVS-75 test result measured on the chassis dynamometer.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.928-933
• /
• 2001

EGR(Exhaust Gas Recirculation) is an effective strategy to control nitrogen oxides emissions from diesel engine. The EGR reduces $NO_x$ through lowering the oxygen concentration in the combustion chamber as well as through heat absorption. However, application of EGR system is difficult because of the penalty in fuel consumption and the increase in particulate matter. The engine used for the experimental was a 3-cylinder 0.8-liter turbo-charged light duty diesel engine with an electronic EGR valve. In this study, experiments were performed at variable vehicle speeds and loads on the chassis dynamometer. To evaluate the exhaust emissions with the EGR system testing was performed using cvs-75 mode test procedure. Results of the cvs-75 mode test achieve sufficiently to meet EURO3 standards.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.183-188
• /
• 2007

Recently, diesel engine has been frequently applied to RV, SUV and light duty truck due to the good fuel economy and high thermal efficiency. $NO_x$ and PM, environmental pollution materials are basically produced in diesel combustion process. The most important target in diesel engine research is the development of system to reduce the emissions of $NO_x$ and PM. Cooled EGR system is an effective method for the reduction of $NO_x$ emission and PM emission from a diesel engine and EGR cooler is the key component of the system. This study investigates the EGR cooler of oval gas tubes compared with the EGR cooler of shell & tubes to verify the heat exchange efficiency of cooler by means of engine dynamometer tests, rig performance tests and numerical analyses.

• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.5
• /
• pp.529-537
• /
• 2000

Several Pt-based oxidation catalysts with different loading were prepared with various metal precursor solutions and characterized with H$_2$ chemisorption and TEM for Pt particle size. V was added to Pt-based catalyst for inhibiting SO$_2$oxidation reaction, as result, Pt-V/Ti-Si catalyst prepared by ERMS(Free Reduced Metal in Solution) method showed high enough activity and better inhibition on SO$_2$oxidation than Pt only catalyst. Optimum Pt particle size for diesel oxidation reaction turned out to be the size of around 20 nm. A prototype catalyst was prepared for light=duty diesel passenger car, and teated for the emission reduction performance with Korean regulation test mode(CVS-75 mode) on chassis dynamometer. The catalyst shows the performance reduction of 75~94% for CO, 53~67% for HC and 10~31% for PM. In the case of heavy-duty diesel catalyst, the domestic formal regulation teat mode D-13 was adopted for both Na engine and Turbo engine. The conversions of CO and THC are high enough(86% and 41%) while the reductions of NOx and PM are relatively low(3~11%).

• Environmental Engineering Research
• /
• v.22 no.3
• /
• pp.294-301
• /
• 2017

This paper is based on experiments conducted on a stationary, four stroke, naturally aspirated air cooled, single cylinder compression ignition engine coupled with an electrical swinging field dynamometer. Instead of 100% diesel, 20% Jatropha oil methyl ester with 80% diesel blend was injected directly in engine beside 25% pre-mixed charge of diesel in mixing chamber and with 20% exhaust gas recirculation. The performance and emission characteristics are compared with conventional 100% diesel injection in main chamber. The blend with diesel premixed charge with and without exhaust gas recirculation yields in reduction of oxides of nitrogen and particulate matter. Adverse effects are reduction of brake thermal efficiency, increase of unburnt hydrocarbons (UBHC), carbon monoxide (CO) and specific energy consumption. UBHC and CO emissions are higher with Diesel Premixed Combustion Ignition (DPMCI) mode compared to compression ignition direct injection (CIDI) mode. Percentage increases in UBHC and CO emissions are 27% and 23.86%, respectively compared to CIDI mode. Oxides of nitrogen ($NO_x$) and soot emissions are lower and the percentage decrease with DPMCI mode are 32% and 33.73%, respectively compared to CIDI mode.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.2
• /
• pp.122-129
• /
• 1995

This is an experimental study on the chassis dynamometer and high way road testing during a severe winter and summer season. Results obtained to compare with the ultrasonic fuel feeding system and conventional fuel system in diesel automobile engine. The results were as followers in case of the ultrasonic fuel feeding system. 1. In chassis dynamometer testing during given vehicle speeds, output were increased from 4.6 to 11.43%, brake specific fuel consumption were increased from 6 to 19%, smoke were decreased from 16.7 to 50%. 2. The running fuel consumption ratio in high way road test were decreased by 15.3% at a severe summer and 20.2% at a severe winter.

• 한국연소학회:학술대회논문집
• /
• 2007.05a
• /
• pp.98-103
• /
• 2007

The number of vehicles employing diesel engines is rapidly rising. Accompanying this trend, application of an after-treatment system is strictly required as a result of reinforced exhaust regulations. The Diesel Particulate Filter (DPF) system is considered as the most efficient method to reduce particulate matter (PM), but the improvement of a regeneration performance at any engine operation point presents a considerable challenge by itself. Temperature, gas compostion and flow rate of exhaust gas are important parameters in DPF evaluation, especially regeneration process. Engine dynamometer and degment tester are generally used in DPF evaluation so far. But these test method couldn't reveal the effect of various parameters on real DPF, such as O2 concentration, amount of soot and exhaust gas temperature. This research has studied the possibility using dump combustor that used to take an approach lean premixed combustion in gas turbine for a DPF power and optimized. It is possible that utilize the system as DOC (Diesel Oxidation Catalyst) and SCR(Selective Catalytic Reduction) assessments test as well as DPF evaluation

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.2 s.257
• /
• pp.188-194
• /
• 2007

New diesel engines equipped with common-rail injection systems and advanced engine management control allow drastic decreases in the production of particulate matters and nitrogen oxides with a significant advantage in terms of the fuel consumption and $CO_2$ emissions. Nevertheless, the contribution of exhaust gas after treatment in the ultra low emission vehicles conception has become unavoidable today. Recently the passive type DPF(Diesel Particulate Filter Trap) system for diesel passenger vehicle has been manufactured into mass production from a French automotive maker since the year of 2000. This passive DPF system fully relies on the catalytic effects from additives blended into the diesel fuel and additives injected into the DPF system. In this study, the effects of PM regeneration in the commercial diesel passenger vehicle with the passive type DPF system were investigated in chassis dynamometer CVS(constant volume sampler)-75 mode. As shown in this experimental results, the DPF regeneration was observed at temperature as low as $350^{\circ}C$. And the engine-controlled the DPF regeneration founded to be one of the most promising regeneration technologies. Moreover, the durability of this DPF system was evaluated with a season weather in terms of the differential pressure and exhaust gas temperature traces from a road test during the total mileage of 80,000km.