• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.206-207
• /
• 2006

This paper describes the dielectric analysis of several insulators for home appliances. The dielectric characteristics of ABS(acrylonitrile butadiene styrene) were tested in relative permittivity, dielectric loss($tan{\delta}$) and specific resistance and compared with those of the other 4 insulators of PE(polyethylene) series. As a result, the relative permittivity of only the ABS slightly decreased with temperature. In the case of the tan6, the ABS showed higher dielectric loss than the other insulators but more excellent thermal performance. In addition, its changing pattern in specific resistance was very similar to that in $tan{\delta}$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.9
• /
• pp.565-570
• /
• 2016

In this work, the complex permittivity of epoxy resins is measured. Epoxy resins, epoxy with micro size fillers and epoxy with micro+nano alumina composites have been evaluated for dielectric properties according to frequency variation. The dielectric spectroscopy measurement and analyses are carried out in the frequency range of $10^{-2}Hz$ to 1MHz and constant to room temperature. The results of dielectric loss suggest that significant improvement in the electrical performance can be expected by using samples containing nano and micro fillers mixture when compared to materials containing only microfillers. As the result, we verified the specific characteristics of dielectric permittivity and dielectric loss namely, relative permittivity become low with improving dispersibility of nano+micro mixture composites and become rise with agglomerate of nano particles.

• Electrical & Electronic Materials
• /
• v.8 no.4
• /
• pp.413-417
• /
• 1995

In order to elucidate the electrical and mechanical properties of insulating paper, it is desirable to study the performances of tensile strength, dielectric constant, dielectric strength. In this work, we constructed the characteristics depending on change of fabrication condition, and these specimens were manufactured by hot press method. As a result, tensile strength was about 75MPa and breakdown was above 5 kV/mm at the minimum value.

• Journal of the Korean Ceramic Society
• /
• v.33 no.9
• /
• pp.977-984
• /
• 1996

This paper analyzes the performance of a rectangular dielectric ceramic antenna by the theoretical cavity model such as input impedance resonant frequency quality factor efficiency and bandwidth. Through a compu-ter simulation variation of the antenna characteristics is found as a function of the antenna parametes. (permit-tivity permeability antenna size etc) Based on the results we propose a new design method for the dielectric ceramic antenna to be employed in Global Positioning Systems.

• Proceedings of the IEEK Conference
• /
• 2002.06a
• /
• pp.431-434
• /
• 2002

In this paper, The resonant frequencies of any modes in the dielectric resonator filter is determined by numberical analysis. The theoretical analysis for the dielectric resonator filter used Ansoft HFSS. We designed the dielectric resonator filter with resonant frequency 4.5 GHz. We describe the characteristics of delivering Power to resonator in different shaped coupling loops. Tile resonant mode of T $E_{01{\delta}}$ and T $E_{01{\delta}}$ could be selected by the horizontal and the vertical coupling loop.p.

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.119-122
• /
• 1987

By cascading the step discontinuities on planar dielectric waveguides with a ferrite layer through two uniform planar dielectric waveguides, nonreciprocal scaterring characteristics of planar dielectric waveguide gratings are analyzed. The calculated results at 35GHz shows that the isolation mechanism takes place near band stop frequency range.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1299-1304
• /
• 2003

Fault current limiters (FCL) are extensively needed to suppress fault currents, especially for trunk power systems heavily connected to high voltage/large current transmission lines. Due to its ideal electrical behavior, high-temperature superconductor fault current limiter (HTSFCL) becomes one of the most important developing trends of limiters in power system. This paper describes the result of an investigation of the dielectric characteristics of turn-to-turn insulation for pancake and solenoid type reactor coil in liquid nitrogen. The influence of thickness in a variety length, on AC, DC and impulse surface flashover has been investigated. Also, the relationships between the number of turn and breakdown characteristics were clarified. The information gathered in this test series should be helpful in the design of liquid nitrogen filled DC reactor type HTSFCL.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1493-1495
• /
• 2003

EVAOH (ethylene-vinyl acetate-vinyl alchol terpolymers) were prepared by using the transesterification reaction between ethylene-vinyl acetate copolymer and alchol. Structural and thermal analyses were accomplished with FTIR and DSC. XLPE (crosslinked polyethylene) and EVAOH were blended using a two-roll mill and their water tree and dielectric loss characteristics were investigated. It is found that the water tree characteristics of XLPE were improved by the addition of EVAOH. It was also found that the extent of improvement of water tree and dielectric loss characteristics of XLPE/EVAOH blends depends on the kind and concentration of EVAOH.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05e
• /
• pp.57-60
• /
• 2003

This paper explained electric field distribution's characteristics of dielectric pellets with a shape of ball to voltage. When discharge gap of electrode and input voltage are each 20[mm], 10000[V], the electric field simulation results of dielectric pellets with a shape of ball with relative dielectric constant of several kind measured stronger electric field near electric pellets with a shape of ball of ${\phi}5$[mm] than $1{\phi}$[mm] and $3.33{\phi}$[mm] at atmosphere. And the maximum electric field of dielectric pellets with a shape of ball over ${\phi}5$[mm] increased about 5[%] to maximum electric field of electric pellets with a shape of ball ${\phi}5$[mm]. And the result of simulation, when relative dielectric constant of dielectric pellets with a shape of ball is 100, it measured about 90[%] of maximum electric field of dielectric pellets with a shape of ball with relative dielectric constant over 1000.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.8
• /
• pp.755-759
• /
• 2008

For the development of a new white dielectric layer in plasma display panel, different $TiO_2$ types as a filler was add to the $Bi_2O_3$-BaO-ZnO glass matrix. The reflectance and dielectric constant of dielectric have been investigated as a function of the mixing content (rutile and anatase), and sintering temperature. The reflectance of dielectric sintered at the 520$^{\circ}C$ appeared most highly and suitable in terms of the adhesion and reflectance of the soda-lime glasses. Also, the thermal expansion coefficient of dielectric was found to be $85.6\times10^{-7}/K$, which was similar to that of the soda-lime glasses. Especially, the dielectric constants were not increased with increasing of $TiO_2$ filler contents.