• 대한기계학회논문집
• /
• 제10권6호
• /
• pp.876-888
• /
• 1986

본 논문에서는 자유 표면과 강체부분이 많은 피어싱 공정의 해석에서 발생하 는 해의 수렴성 저하를 방지하기 위하여 비정상 상태의 가공경화 효과와 강체 연속처리 리방법을 프로그램 개발에 적용하고 프로그램 개발에 적용하고 프로그램 범용성을 높 이기 위해 초기 속도장 발생 프로그램을 개발하여 본 공정 해석에 적용하여 보려고 한 다. 또한 재료를 가공 경화를 고려한 강소성체(rigid-plastic material)로 가정해서 시편에 크랙이 발생하여 파괴될때까지 컴퓨터 시뮬레이션을 수행한 후 냉간 피어싱 공 정에 있어서 표면 크랙의 발생과 성장 그리고 파괴에 가장 많은 영향을 미치는 인자들 을 계산결과를 토대로 실험과 비교조사하고, 실험 시편의 지름과 높이 그리고 마찰상 태를 다르게 조합해서, 실험과 계산을 시하여 시편 모양에 따른 변형 모우드(mode)와 파괴 모우드의 차이를 규명해 보기로 한다.

• Tribology and Lubricants
• /
• 제31권4호
• /
• pp.157-162
• /
• 2015

In this study, an ultrasonic nanocrystalline surface modification (UNSM) technique is applied to tungsten carbide-cobalt (WC-Co) to extend the service life of carbide parts used in press mold. The UNSM technique modifies the structure, reduces the surface roughness, increases the surface hardness, induces the compressive residual stress, and increases the wear resistance of materials by introducing severe plastic deformation. The surface roughness, hardness, and compressive residual stress of WC after UNSM treatment improve by about 42, 10, and 71%, respectively. A wear test under dry conditions is used to assess the effectiveness of the UNSM technique on the friction and wear behavior of WC. The UNSM technique is found to reduce the WC friction coefficient by approximately 21% and enhance the wear resistance by approximately 85%. The improved friction and wear behavior of WC may be mainly attributed to the increased hardness and compressive residual stress. Moreover, the WC specimen is treated by UNSM technique using three different WC, silicon nitride (Si₃N₄) and stainless steel (STS304) balls. The surface treated by WC balls shows the highest hardness when compared with treatment by stainless steel and silicon nitride balls. According to the obtained results, the UNSM technique is believed to increase the durability of the carbide component by improving the friction and wear behavior.

• 소성∙가공
• /
• 제11권8호
• /
• pp.682-690
• /
• 2002

The formation of adiabatic shearband in tungsten heavy alloys(WHA) was studied in this investigation. Five prismatic specimens were loaded by high velocity impacts and treated as plane strain problems. To find out the effect of particle's volume ratio, specimens containing 81%, 93% and 97% volume percents of tungsten particles were used. Also the effects of particle's geometry and size on the formation of shearband were studied for 81% volume percent alloys by small size particle model, large size particle model and undulated particle models, and the results were discussed.be used to diagnose the causes of necking and fracture in industrial practice and to investigate whether these defects were caused by material property variation, changes in lubrication, or incorrect press settings. In non-axisymmetric deep drawing, three modes of forming regimes are found: draw, stretch, plane strain. The stretch mode for non-axisymmetric deep drawing could be defined when the major and minor strains are positive. The draw mode could be defined when the major strain is positive and minor strain is negative, and plane strain mode could be defined when the major strain is positive and minor strain is zero. Through experiments the draw mode was shown on the wall and flange are one of a drawn cup, while the plane strain and the stretch mode were on the punch head and the punch corner area respectively, We observed that the punch load of elliptical deep drawing was decreased according to increase of die corner radius and the thickness deformation of minor side was more large than major side.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.589-592
• /
• 2005

Micro-forming is a suited technology to manufacture very small metallic parts(several $mm{\sim}{\mu}m$). Micro-forming of $Zr_{62}Cu_{17}Ni_{13}Al_8$ bulk metallic glass(BMG) as a candidate material for this developing process are feasible at a relatively low stress in the supercooled liquid state without any crystallization during hot deformation. In this study, micro-formability of a representative bulk metallic glass, $Zr_{62}Cu_{17}Ni_{13}Al_8$, was investigated for micro-forging of U-shape pattern. Micro-formability was estimated by comparing $R_f$ values $(=A_f/A_g)$, where Ag is cross-sectional area of U groove, and $A_f$ the filled area by material. Microforging process was simulated and analyzed by applying finite element method. FEM simulation results should reasonable agreement with the experimental results when the material properties and simulation conditions such as top die speed, remeshing criteria and boundary conditions tightly controlled. The micro-formability of $Zr_{62}Cu_{17}Ni_{13}Al_8$ was increased with increasing load and time in the temperature range of the supercooled liquid state. Also, FEM Simulation using DEFORM was confirmed to be applicable for the micro-forming process simulation.

• Design & Manufacturing
• /
• 제14권4호
• /
• pp.65-70
• /
• 2020

Partial reinforcement of sheet metal parts with CFRP patch is a technology that can realize ultra-lightweight body parts while overcoming the high material cost of carbon fiber. Performing these patchworks with highly productive press equipment solves another issue of CFRP: high process costs. The A-pillar is the main body part and has an undercut shape for fastening with other parts such as roof panels and doors. Therefore, it is difficult to bond CFRP patches to the A-pillar with a general press forming tool. In this paper, a flexible system that applies uniform pressure to complex shapes using ceramic particles and silicone rubber is proposed. By benchmarking various A-pillars, a reference model with an undercut shape was designed, and the system was configured to realize a uniform pressure distribution in the model. The ceramic spherical particles failed to realize the uniform distribution of high pressure due to their high hardness and point contact characteristics, which caused damage to the CFRP patch. Compression equipment made of silicone rubber was able to achieve the required pressure level for curing the epoxy. Non-adhesion defects between the metal and the CFRP patch were confirmed in the area where the bending deformation occurred. This defect could be eliminated by optimizing the process conditions suitable for the newly developed flexible system.

• Design & Manufacturing
• /
• 제16권3호
• /
• pp.9-15
• /
• 2022

In order to reduce the manufacturing costs of the glass lens, it is necessary to manufacture a lens using a UV curable resin or a thermosetting resin, which is a curable material, in order to replace a glass lens. In the case of forming a lens using a thermosetting material, it is necessary to form several lenses at once using the wafer-level lens manufacturing technologies due to the long curing time of the material. When a lens is manufactured using a curable material, an error in the shape of the lens due to the shrinkage of the material during the curing process is an important cause of defects. The major factors for these shape errors and deformations are the shrinkage and the change of mechanical properties in the process of changing from a liquid material during curing to a solid state after complete curing. Therefore, it is necessary to understand the curing process of the material and to examine the shrinkage rate and change of physical properties according to the degree cure. In addition, it is necessary to proceed with CAE for lens molding using these and to review problems in lens manufacturing in advance. In this study, the viscoelastic properties of the material were measured during the curing process using a rheometer. Using the results, Rheological investigation of cure kinetics was performed. At the same time, The shrinkage of the material was measured and simple mathematical models were created. And using the results, the molding process of a single lens was analyzed using Comsol, a commercial S/W. In addition, the experiment was conducted to compare and verify the CAE results. As a result, it was confirmed that the shrinkage rate of the material had a great influence on the shape precision of the final product.

• Design & Manufacturing
• /
• 제16권4호
• /
• pp.67-74
• /
• 2022

Injection molding is a cyclic process comprising of cooling phase as the largest part of this cycle. Providing efficient cooling in lesser cycle times is of significant importance in the molding industry. Recently, lots of researches have been done for rapid cooling of a hot-spot area using CO2 in injection molding. The CO2 flows under high pressure through small, flexible capillary tubes to the point of use, where it expands to create a snow and gas mixture at a temperature of -79℃. The gaseous CO2 removes heat from the mold and releases it into the atmosphere. In this paper, a CO2 cooling module was applied to an injection mold in order to cool a large area cavity uniformly and quickly, and the cooling performance of the injection mold was investigated. The product was a high-curvature molded part with a molding area of 300x100mm. Heat cartridges were installed in a stationary mold, and CO2 cooling module was inserted inside a movable mold. Through structural analysis, it was confirmed that the maximum deformation of mold with CO2 cooling module was 0.09mm. A CO2 feed system with a heat exchanger was used for cooling experiments. The CO2 was injected into the holes on both sides of the supply pipe of the cooling module and discharged through hexagon blocks to cool the mold. It took 5.8 seconds to cool the mold from an average temperature of 140℃ to 70℃. Through the experiment using CO2 cooling module, it was found that a cooling rate of up to 12.98℃/s and an average of 10.18℃/s could be achieved.

• 한국산학기술학회논문지
• /
• 제18권3호
• /
• pp.320-326
• /
• 2017

다단 딥드로잉 기술은 제품의 생산성 향상과 비용 절감을 위해 휴대폰 배터리 케이스 제품의 생산 공정으로 많이 사용하고 있다. 휴대폰 배터리 케이스는 용량과 강성을 목적으로 세장비가 큰 사각 컵 형상으로 제조된다. 사각 컵 형상의 다단 딥드로잉은 세장비가 크고, 복잡한 변형 형태 메커니즘으로 인한 제품의 좌우 높이 차이가 발생한다. 이로 인해 제품 조립과 표면 품질에 문제가 발생한다. 본 연구에서는 이러한 문제를 개선하기 위해 제품의 높이 차이가 최소가 되는 블랭크 형상에 대해 연구했다. 제품 좌우 높이 차이가 최소가 되는 블랭크 형상을 찾기 위해 최적 설계와 해석을 수행했다. 타원형 블랭크의 장변과 단변을 설계 변수로 설정하고, 목적 함수는 높이 차이가 최소가 되도록, 제품의 두께 감소율이 목표 범위에 도달하도록 설정했다. 또한 최종 제품 형상의 높이를 구속 조건으로 설정하였다. 그 결과 최적 설계를 통한 초기 블랭크 설계로 높이 차이가 최소가 되었으며, 원하는 공정을 지정하여 높이 차이가 최소화 되도록 수행 가능하다. 향후 개발된 자동화 프로세스로 인해 모든 각형 타입의 초기 소재 설계가 가능할 것으로 판단된다.

• 마이크로전자및패키징학회지
• /
• 제21권1호
• /
• pp.31-39
• /
• 2014

최근 모바일 응용 제품에 사용되는 반도체 패키지는 고밀도, 초소형 및 다기능을 요구하고 있다. 기존의 웨이퍼 레벨 패키지(wafer level package, WLP)는 fan-in 형태로, I/O 단자가 많은 칩에 사용하기에는 한계가 있다. 따라서 팬 아웃 웨이퍼 레벨 패키지(fan-out wafer level package, FOWLP)가 새로운 기술로 부각되고 있다. FOWLP에서 가장 심각한 문제 중의 하나는 휨(warpage)의 발생으로, 이는 FOWLP의 두께가 기존 패키지에 비하여 얇고, 다이 레벨 패키지 보다 휨의 크기가 매우 크기 때문이다. 휨의 발생은 후속 공정의 수율 및 웨이퍼 핸들링에 영향을 미친다. 본 연구에서는 FOWLP의 휨의 특성과 휨에 영향을 미치는 주요 인자에 대해서 수치해석을 이용하여 분석하였다. 휨을 최소화하기 위하여 여러 종류의 epoxy mold compound (EMC) 및 캐리어 재질을 사용하였을 경우에 대해서 휨의 크기를 비교하였다. 또한 FOWLP의 주요 공정인 EMC 몰딩 후, 그리고 캐리어 분리(detachment) 공정 후의 휨의 크기를 각각 해석하였다. 해석 결과, EMC 몰딩 후에 발생한 휨에 가장 영향을 미치는 인자는 EMC의 CTE이며, EMC의 CTE를 낮추거나 Tg(유리천이온도)를 높임으로서 휨을 감소시킬 수 있다. 캐리어 재질로는 Alloy42 재질이 가장 낮은 휨을 보였으며, 따라서 가격, 산화 문제, 열전달 문제를 고려하여 볼 때 Alloy 42 혹은 SUS 재질이 캐리어로서 적합할 것으로 판단된다.

• 대한조선학회논문집
• /
• 제48권6호
• /
• pp.528-538
• /
• 2011

As a forming method for curved hull plates more efficient than the flame bending, mechanical bending using multi point press forming and die-less forming is discussed in this paper. the mechanical forming is a flexible manufacturing system for automatically forming of hull parts. It is especially suited to varied curved parts. This paper discusses a multiple point pressing machine composed of a pair of reconfigurable punches in order to achieve the rapid forming of curved hull plates using division forming and presents how forming information is obtained from the given design surface. Although the mechanical forming can be efficient in the metal forming, spring back after pressing is a phenomenon which must be carefully considered when quantifying the process variables. If the spring back is not accurately controlled, the fabricated shell plate cannot meet assembly tolerance. This paper describes the principles to calculate the proper stroke of each punch at the divided areas. the strokes are determined by an iterative process of sequential pressing and spring back compensation from an unfolded flat shape to its given design surface. FEA(finite element analysis) is used to simulate the spring back of the plate and the IDA(iterative displacement adjustment) method adjusts the offset of pressing punches from the deformation results and the design surface. The shape deviations of two surfaces due to spring back are compensated by integrated system using FEA and IDA method. For the practical application, It is aimed to develop an integrated system that can automatically perform the compensation process and calculate strokes of punches of the double sides' reconfigurable multiple-press machine and some experimental results obtained with mechanical bending are presented.