• Design & Manufacturing
• /
• v.17 no.3
• /
• pp.48-54
• /
• 2023

In this study, an injection mold with ultra-small surface properties was manufactured using nanosecond laser processing. A superhydrophobic characteristic analysis was performed on the PET specimen manufactured through this. To this end, a hydrophobic pattern was defined using the Cassie-Baxter model. The defined features were selected with a spot diameter of 25um and pitch spacing of 30um and 35um. As a result of the basic experiment, it was confirmed that the fine pattern shape had an aspect ratio of 1:1 when the pitch interval was 35um and 20 iterations. Through the determined processing conditions, a hydrophobic pattern was implemented on the core surface of KP4. A specimen with a hydrophobic pattern was produced through injection molding. The height of the molded hydrophobic pattern is 20 ㎛ less than the depth of the core and the contact angle measurement results are 92.1°. This is a contact angle smaller than the superhydrophobic criterion. Molding analysis was performed to analyze the cause of this, and it was analyzed that the molding was not molded due to the lack of pressure in the injection machine.

• Design & Manufacturing
• /
• v.18 no.2
• /
• pp.1-8
• /
• 2024

Unlike the roll-to-roll process that uses a steel roll and a nip roll, a vacuum roll can hold and transfer a thin film using a single roll. To precisely manufacture a vacuum roll, a thin outer cylinder must be machined, which is assembled on the outside of the roll and contacts the film via vacuum pressure. In this study, the effects of jaw width and chucking force on the deformation of the outer cylinder during the turning process were investigated using analysis, and a precision machining and burr removal process was developed. The deformation of the outer cylinder decreased almost linearly with increasing jaw width and increased with higher chucking force and larger cylinder diameter. Additionally, the deflection due to the weight of the outer cylinder was approximately three times greater than that caused by film tension. For the machined outer cylinder, a burr removal experiment was conducted, and concentricity and cylindricity were measured. Using a device that removes burrs by rotating a wheel connected to the main shaft at high speed, it was found that burrs generated on the inner diameter could be removed very efficiently. On the vacuum side, the concentricity errors of the inner and outer diameters were 0.015 mm and 0.014 mm, respectively, and on the opposite side, they were 0.006 mm and 0.010 mm, respectively. Additionally, the measurement of Total Indicator Runout (TIR) according to the angle showed that the maximum cylindricity of the outer and inner diameters was 0.02 mm and 0.025 mm, respectively. Finally, through burr-height measurement at the hole boundary, it was found that the heights were within 0.05 mm.

• Korean Journal of Medicinal Crop Science
• /
• v.10 no.5
• /
• pp.419-422
• /
• 2002

Korean angelica(Angelica gigas Nakai), a oriental medicinal plants is important and in great demand in Korea. This crop is a biennial which is to die after flower, so as could not harvest the root. A new variety 'Anpung' was developed from the selection of the local collecting population by medicinal crop team at NCES in 2001. This showed stable bolting during its cropping year and have high quality and yield potential. The color is greenish purple in stem and red purple in flower. It was longer in plant height and root length, thicker in root diameter, more leave and latheral roots comparing with the check variety 'Manchu'. The dry root was 72 g/plant showing heavier than check variety of 65 g/plant. It showed such low bolting rate as 0.5%, on the other hand 49.3% in landrace when it cultured by transplanting with heating nursery seedlings, and $0{\sim}15%$ with field nursery seedlings. The dry root yield of the variety was averaged 3,630 kg/ha out yielding the check variety by 11% at the three regional yield test from 1999 to 2001. Finally, 'Anpung' showed higher content of extracts up to 46.3% in 'Anpung' and 45% in check variety, decursin and decursinol contents was 3.48% and 2.79%, showing slightly higher than check variety.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.7 no.4
• /
• pp.213-218
• /
• 2009

Electrowinning process recovers uranium with actinide elements from spent fuels and is a key step in the Pyroprocessing because of proliferation resistance. An analysis of heat transfer of the Electrowinning cell was conducted to develop basic tool for designing engineering-scale Electrowinner. For the calculation of the heat transfer, ANSYS CFX commercial code was adapted. As a result of the calculation, the vertical Heating Zone length had great effect upon temperature of LiCl-KCl eutectic salt. To maintain constant temperature in the salt, the Heating Zone length should be three times longer than the height of the salt. However, the argon and salt temperatures were barely affected by the Cooling Zone length. The temperature under the Cell cover was mainly influenced by the number of the cooling plates. When the cooling plates were installed more than the number of 5, temperature under the cover was maintained below $250^{\circ}C$. These temperature properties had similar tendency toward the temperature of the Cell which was measured from experiments, Simulated heat transfer information from this study could be used to design engineering-scale Electrowinner.

• The Journal of Korean Academy of Prosthodontics
• /
• v.39 no.3
• /
• pp.260-272
• /
• 2001

All-ceramic restorations have had a more limited life expectancy than metal ceramic restorations because of their low strength. Their relatively lower strength and resistance to fracture have restricted the use of all-ceramic crowns to anterior applications where occlusal loads are lower. But there has been increasing interest in all-ceramic restorations because patients are primarily concerned with improved esthetics. Many efforts have been made to in prove the mechanical properties of dental ceramics. This study was designed to elucidate the influence of the luting agent on the strength of the Empress 2 crown (staining technique) cemented on human teeth. Seventy extracted human permanent molar teeth were chosen. Teeth were prepared for Empress 2 crowns with milling machine on a surveyor. A dental bur was placed in the mandrel that was positioned so that the long axis of the bur was perpendicular to the surveyor base. Dimensions of the Empress 2 crown preparation were $6^{\circ}$ taper on each side, $1.5{\pm}0.1mm$ shoulder margin, and 4mm crown height. The luting cements used in this study were as follow: 1. Uncemented 2. Zinc phosphate cements (Confi-Dental) 3. Conventional glass ionomer cement : Fuji 1 (GC) 4. Resin-modified glass ionomer cements : Fuji plus (GC) 5. Adhesive cements : Panavia F (Kuralay), Variolink II (Vivadent), Choice (Bisco). Fracture test using Instron. The crowns were loaded in compressive force to evaluate the effect of these cements on the breaking strength of these all-ceramic crowns. A steel ball with a diameter of 4mm was placed on the occlusal surface and load was applied to the steel ball by a cylindrical bolt with a crosshead speed of 0.5mm per minute until fracture occurred. The fractured surface was examined using Scanning Electron Microscopic Image (SEM) to discover the correlation between fracture strength and bonding capacity. Within the limitation of this in vitro study design, the results were as follows : 1. fomentations significantly increased the fracture resistance of Empress ceramic crowns compared to control. Uncemented (206.9 N): ZPC (812.9 N): Fuji 1 (879.5 N): Fuji Plus (937.7 N): Choice (1105.4 N): Variolink II (1221.1 N): Panavia F (1445.2 N). 2. Resin luting agent, treated by a silane bond enhancing agents, yielded a significant increase in fracture resistance. In some of the Panavia F group, a fracture extended into dentin. 3. According to SEM images of fractured Empress crowns, the stronger the bond at both interfaces(crown and die), the more fracture strength was acquired.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.302-307
• /
• 2016

The technology of multistage deep drawing has been widely applied in the metal forming industry, in order to reduce both the manufacturing cost and time. A battery can used for mobile phone production is a well-known example of multistage deep drawing. It is very difficult to manufacture a battery can, however, because of its large thickness to height aspect ratio. Furthermore, the production of the final parts may result in assembly failure due to springback after multistage deep drawing. In industry, empirical methods such as over bending, corner setting and ironing have been used to reduce springback. In this study, a bottoming approach using the finite element method is proposed as a practical and scientific method of reducing springback. Bottoming induces compression stress in the deformed blank at the final stroke of the punch and, thus, has the effect of reducing springback. Different cases of the bottoming process are studied using the finite element program, DYNAFORM, to determine the optimal die design. The results of the springback simulation after bottoming were found to be in good agreement with the experimental results. In conclusion, the proposed bottoming method is expected to be widely used as a practical method of reducing springback in industry.

• Horticultural Science & Technology
• /
• v.34 no.5
• /
• pp.727-735
• /
• 2016

This research was conducted to investigate the influence of various pre-planting $NO_3:NH_4$ ratios in the coir dust+peatmoss+perlite (3.5:3.5:3, v/v/v) medium on the growth of tomato plug seedlings (cv. Dotaerang Dia), changes in chemical properties of root media, and tissue nutrient contents. With the fixation of N concentration to $300mg{\cdot}L^{-1}$, the $NO_3:NH_4$ ratios were adjusted to 100:0, 73:27, 50:50, 27:73, 0:100. Then, root media containing various $NO_3:NH_4$ ratios and equal concentration of other essential nutrients were filled into 50-cell plug trays and the seeds of 'Dotaerang Die' tomato were sown. The investigation of seedling growth and tissue analysis for mineral nutrient contents based on the dry weight of above-ground tissue were conducted 6 weeks after sowing. As seedlings grew, the EC decreased quickly and pH increased gradually in the all treatment media. The plant height, fresh weight and dry weight of seedlings in the treatment of 50:50 ($NO_3:NH_4$) were 29.0 cm, 13.7 g, and 1.21 g, respectively, which were the highest among treatments tested. However, the seedlings in the treatment of 0:100 ($NO_3:NH_4$) had 26.5 cm, 11.2 g, and 0.92 g in plant height, fresh weight and dry weight, respectively. These were the poorest among the treatments tested. The tissue contents of N were 2.77 to 3.22% in all the treatments. The treatment of 27:73 ($NO_3:NH_4$) had the highest contents of Fe, Mn and Zn and that of 0:100 ($NO_3:NH_4$) had the lowest contents of Mg, Na, Cu, Mn and Zn among the treatments tested. The results indicate that $NH_4$ ratio should be lower than 50% in the coir dust+peatmoss+perlite (3.5:3.5:3, v/v/v) medium for seedling growth of tomato and the optimum ratio will be used to draw up guide lines for plug seedling production.