• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2003.10a
• /
• pp.181-184
• /
• 2003

본 연구에서는 열 필라멘트 화학증착 방법에 의한 나노 다이아몬드 박막 증착을 위해 핵 생성 밀도를 증가시키기 위해서 다이아몬드 특성을 갖는 탄소(Diamond-Like Carbon)박막들을 연속 및 펄스 플라즈마를 이용한 화학 증착법에 의하여 증착하여 그 특성을 SEM, XPS, Raman 및 Nano-Tester를 이용하여 분석하였으며 열 필라멘트 화학 증착법에 의하여 나노 다이아몬드 박막 형성에 대한 핵 밀도와 다아이몬드 특성을 갖는 탄소 박막의 특성의 연관성을 관찰하여 공구(WC-Co)의 표면 사전 처리 없이 나노 다이아몬드 박막 형성을 용이하게 하는 실험을 수행하였다.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.203-205
• /
• 1996

DLC(Diamond-Like Carbon) films were prepared by Inductively Coupled Plasma(ICP) CVD system. It was confirmed that the field emission characteristics are closely related to the richness of C-H bonding incorporated in the DLC. According to Fowler-Nordheim equation, it is thought that the ability of DLC to emit electron at relatively low voltage is due to the field enhancement caused by the nodules of ${\sim}100nm$ size on the surface of DLC. The electric field to start field emission was about $1.4{\times}10^9V/m$ in case of DLC film deposited at input power of 400W and substrate bias of -100V.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.5
• /
• pp.426-430
• /
• 2000

We have studied the field emission characteristics of multi-layered diamond-like-carbon (DLC) films deposited by vertical electrodes type plasma enhanced chemical vapor deposition with CH$_4$ and H$_2$ mixture. We deposited a thin layer of DLC on the p$^{+}$-Si substrate and then turned off plasma before another deposition of a new DLC layer. The thickness and the number of DLC layers are varied. The emission characteristics of multi-layered DLC films were compared with conventional one. The multi-layered DLC film shows higher emission current than conventional one.e.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.4
• /
• pp.173-178
• /
• 2009

DLC film was synthesized on plastic injection mold(SKD11, $30\;mm\;{\times}\;19\;mm\;{\times}\;0.5\;mm$) and Si(100) wafer for 2 h at $130^{\circ}C$ under 6 mTorr using hybrid method of rf sputtering and ion source. The obtained film was analysed by Raman spectroscopy, AFM, TEM, Nano indenter and scratch tester, etc. The film was defined as an amorphous phase. In the Raman spectrum, broad peak of $sp^2$-bonded carbon attributed to graphite at $1550\;cm^{-1}$ were observed, and the ratio of ID($sp^3$ diamond intensity)/IG($sp^2$ graphite intensity) was approximately 0.54. The adhesion of DLC film was more than 80 N with scratch tester when $0.2\;{\mu}m$ thickness Cr was coated as interlayer. The micro-hardness was distributed at 35~37 GPa. The friction coefficient was 0.02~0.07, and surface roughness(Ra) was 0.34~1.64 nm. The lifetime of DLC coated plastic injection mold using as a connector part in computer was more than 2 times of non-coated mold.

• Journal of the Korean Vacuum Society
• /
• v.10 no.4
• /
• pp.387-395
• /
• 2001

The elastic modulus and the structural evolution were examined with the film thickness in polymeric, hard, graphitic diamond-like carbon (DLC) films. The DLC films used in the present study were prepared by radio frequency plasma assisted chemical vapor deposition (r.f.-PACVD) from $C_6H_6\;and\;CH_4$ gas. Elastic modulus of very thin DLC film was measured by free overhang method. This method has an advantage over the other methods. Because the substrate was removed by etching technique, the measured value is not affected by the mechanical property of the substrate. The structural evolution was investigated by the G-peak position of the Raman spectrum. The polymeric and graphitic films exhibited the decreased elastic modulus with decreasing film thickness. In polymeric films, the reason was that more polymeric film had been deposited in the initial stage of the film growth and in graphitic film more graphic films which had been deposited in the initial stage decreased the elastic modulus. The G-peak position of the Raman spectrum confirmed this result. On the other hand, the hard film showed the constant elastic modulus regardless to the film thickness. The structural change was not observed in this range of the film thickness.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.69-69
• /
• 2002

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2005.11a
• /
• pp.169-169
• /
• 2005

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2001.11a
• /
• pp.71-71
• /
• 2001

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.29-29
• /
• 2011

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.6
• /
• pp.962-967
• /
• 2017

The Diamond-Like-Carbon (DLC) coating is a new carbon-based amorphous material. Carbon ions in the plasma are electrically accelerated and collide with the substrate to form a thin film. This film has similar properties to diamonds such as high surface hardness, low coefficient of friction, corrosion resistance and durability that do not react with acids and bases. Also, since there is no thermal deformation, it can be printed at room temperature. and coated on almost all materials such as paper, polymer, ceramics and various metals even aspheric lens it is possible to mirror surface coating with excellent surface roughness. In this paper, we have analyzed the DLC film formed by Filtered Arc Ion Plating (Filtered AIP) process.