• 비파괴검사학회지
• /
• 제28권2호
• /
• pp.125-130
• /
• 2008

레이저 용접부의 국소 잔류응력을 측정하기 위한 비파괴 기법으로 구형압입시험이 제안되었다. 용접상태 절단휠의 구형압입시험으로 얻어진 겉보기 항복강도와 절단횔 용접부에 대한 응력완화 열처리 이후 동등한 위치에서 구한 고유 항복강도를 정량적으로 비교하였다. 고유항복강도가 탄성한도 내의 잔류응력에 의해서 변화하지 않는다고 고려하면 용융선으로부터 거리에 따른 두 항복강도의 차이가 용접잔류응력의 분포로 나타난다. 레이저 용접된 다이아몬드 절단휠의 구형압입시험으로부터 약 10 mm 폭에 걸친 잔류응력의 분포를 확인하였으며, 잔류응력은 쌩크와 절단팁 내에서 각각 최대 압축 및 인장 잔류응력치를 나타내었다.

• Restorative Dentistry and Endodontics
• /
• 제22권2호
• /
• pp.792-800
• /
• 1997

The purpose of this study was to evaluate the adaptation of self-cured glass ionomer cement and resin-modified glass ionomer cement and polyacid-modified resin composite, which are light-cured giass ionomer cements, to dentin surface. Twelve extracted human maxillary and mandibular molar teeth were used in this study. The entire occlusal dentin surfaces of teeth were exposed with Diamond Wheel Saw and smoothed with sand papers (300, 600, 1200grits). They were randomly assigned into 3 groups according to glass ionomer cements used; Control group- Fuji II, Expeimental group 1 - Fuji II LC, Expeimental group 2 - Dyract. According to the manufacturer's directions, three glass ionomer cements were bonded to exposed dentin surfaces of the tooth crown and cured. Crowns and glass ionomers were trimmed after 24hrs and sectioned horizontally and vertically with diamond saw. The interface of glass ionomer cements and dentin was examined under SEM. The results were as follows : 1. Good adatation between glass ionomer cement and dentin on the horizontal section was showed in control and experimental group 1, but the gap of $20{\mu}m$, which was observed distinct separation between glass ionomer cement and dentin, was showed in experimental group 2. 2. Good adatation between glass ionomer cements and dentin on the vertical section was showed in control and experimental group 1, but the gap of 80-$100{\mu}m$ was showed in experimental group 2. 3. Cohesive fracture within glass ionomer cements in control and experimental group 1 was showed, but no cohesive fracture was showed in experimental group 2.

• 한국자동차공학회논문집
• /
• 제1권2호
• /
• pp.103-116
• /
• 1993

Recently, engineering ceramics called as the 3 material have been concerned significantly with some excellent mechanical properties and many functions as new materials for high precision mechanical components and engineering parts for at large. Then, for designing engineering parts using engineering ceramics, bending strength value data with high reliability is more essential than any other mechanical properties. But, because of brittleness and structural characteristic, it is very hard to grind with conventional tools, and the generation of cracks and various defects of engineering ceramics parts during grinding machining process are serious problems. Thus, in present study, surface grinding experiments with various machining conditions using resin bond diamond wheels are carried out to obtain the most excellent guality of testpiece surface and optimum step of grinding process for the high efficient stock removal rate to save running time. As the results from grinding experiments and 3-points bending strength test of ground Al2O3 ceramics parts on Korean Standard, manufactured in our country and Japan, basic technology and know-how to develop the optimum grinding machining conditions and also high bending strength values with high reliability are obtained.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.108-113
• /
• 2005

In this study, rotary type diamond dressing system for ultra-precision centerless grinding for ferrule was developed at the first time and experiments were conducted with AE sensor and hall sensor system to verify the optimum dressing condition for ultra-precision centerless grinding for ferrule. The correlations with the condition of dressing are evaluated by AE signal analysis with root mean square (RMS) and frequency analysis. And current signals from hall sensor are also studied as a factor of dressing optimum condition selection. Dressing process was conducted to investigate the effects of depth of cut, rotating speed, and the number of overlap to select the optimum condition of rotary dressing system of ultra-precision centerless grinding machine for ferrule fabrication. In order to verify the optimum condition of dressing, AE and current signals were compared with the surface quality of dressing wheel and grinding wheel for ultra-precision ferrule grinding. All of these experiments were completed by Taguchi Methodology to reduce experimental time. Hence, the optimum condition of rotary dressing system for ultra-precision centerless grinding for ferrule fabrication can be selected following to the experiment result from signals of AE and hall sensor.

• 한국정밀공학회지
• /
• 제19권8호
• /
• pp.141-146
• /
• 2002

This paper has studied to obtain the grinding characteristics and optimal grinding conditions of ceramic materials in the grinding with diamond wheel by design of experiments. The load on wheel by varying the feed rate was related with the surface roughness due to the minute destruction phenomenon of grains for the $Si_3\;N_4\;and\;ZrO_2$. The depth of cut is related with the surface roughness because the grinding is carried out by grain shedding process due to the brittle fracture phenomenon for the $A1_2\;O_3$. The major factors affecting the surface roughness and the optimum grinding conditions were obtained with minimum experiments using design of experiments.

• International Journal of Precision Engineering and Manufacturing
• /
• 제6권1호
• /
• pp.59-64
• /
• 2005

This paper describes an investigation about the fluid delivering method that minimizes the generation of hydrodynamic pressure and improves the grinding accuracy. Traditionally, grinding fluid is delivered for the purpose of cooling, chip flushing and lubrication. Hence, a number of conventional investigations are focused on the delivering method to maximize fluid flux into the contact arc between the grinding wheel and the work piece. It is already known that hydrodynamic pressure generates due to this fluid flux, and that it affects the overall grinding resistance and machining accuracy. Especially in the ultra-precision mirror grinding process that requires extremely small amount of cut per pass, its influence on the machining accuracy becomes more significant. Therefore, in this paper, a new delivering method of grinding fluid is proposed with focus on minimizing the hydrodynamic pressure effect. Experimental data indicates that the proposed method is effective not only to minimize the hydrodynamic pressure but also to improve the machining accuracy.

• 한국공작기계학회논문집
• /
• 제11권3호
• /
• pp.86-92
• /
• 2002

In this study, experiments were carried out to investigate the characteristics of grinding and wear process of diamond wheel far ceramic materials. Normal component of grinding resistance of $Al_2$O$_3$ was less then that of $Si_3 N_4$ and $ZrO_2$. This seems to be the characteristics of ceramic tools on work pieces both of high hardness. For the case of $Si_3 N_4$ and $ZrO_2$, as the mesh number of wheel increases, the surface roughness decreases. For the case of $Al_2 O_3$, the surface roughness does not decreases. Specific binding energy decreases as the material removal rate per unit time increases. For the case of $Si_3 N_4$ and $ZrO_2$, grinding is carried out by abrasive wear processes. For the case of $Al_2 O_3$, grinding is carried out by grain shedding process due to brittle fracture.

• 대한치과교정학회지
• /
• 제22권1호
• /
• pp.123-131
• /
• 1992

This study was done to evaluate the changes of enamel surface by interproximal stripping and recovery of it by polishing. The number of 34 1st premolars which had extracted for orthodontic treatment were selected as samples. Interproximal stripping was performed by hand with metal strip and strip placer (Dentaurum Co., Germany) and low speed handpiece with diamond disk (Superdiaflex, Germany). Polishing was performed by hand with plastic strip (3M Col) and low speed handpiece with whip-mix, DCPA (Dicalcium Phosphate, Anhydrous, $CaHPO_4$) powder and Sof-lex (3M Co. U.S.A.) polishing kit. Each groups were examined under the scanning electron microscope (JEOL Co., JSM-840A, Japan) and the following results were obtained: 1. The stripped group performed by metal strip and diamond disk altogether showed deep furrow on the enamel surface as wide as about $10{{\mu}m}$. 2. There could be seen more irregular scratched line in the group stripped by metal strip than that by diamond disk. 3. The polished group performed by plastic strip and DCPA powder showed slight smoothening of the edge of stripped furrow on the enamel surface without relation to the stripping method. 4. The polished group performed by Sof-lex progressive polishing kit could not avoid the formation of the furrows on the enamel surface according to the particle size without relation to the stripping method. 5. The polished group performed by the superfine polishing wheel, the final stage of Sof-lex polishing method showed shallow scratched line as wide as within about $2{{\mu}m}$ on the enamel surface without relation to the stripping method. 6. The interproximal stripped enamel surface could not recover its original surface texture by any kind of polishing methods.

• 대한치과보철학회지
• /
• 제34권2호
• /
• pp.246-265
• /
• 1996

After adjusting glazed surface of laminate veneer porcelain by reduction in the clinical procedure, an additional polishing procedure is required to smoothen the roughened surface by reduction, as it is difficult to glaze it again in the furnace. In this study, four kinds of laminate veneer porcelain were ground with diamond points as done in the clinical procedure. The adjusted porcelain surface was polished with Durawhite stone, Ceramiste points, Exa cerapol, Porcelain polishing wheel, Diamond polishing paste. The degree of surface roughness was evaluated with SEM and profilometer at each step, The self glazed surface and the glazed surface with glazing powder were compared with the polished surface and surface roughness of four kinds of laminate veneer porcelain according to the polishing method and step were obserbed. The following results were obtained : 1. There was no difference in the average surface roughness Ra value and the surface roughness obserbed under SEM according to the polishing methods and steps used, among the four kinds of laminate veneer porcelain including Colorlogic, Exelco, Vintage, and Vitadur alpha product. 2. Due to porosities, the surface in the course of polishing by polishing instruments was rougher than the glazed surface, evaluated with a SEM. 3. Insta-Glaze diamond polishing paste has no statistical difference with self glazed group 1, although it has a lower value in average surface roughness Ra value. 4. Group 2 which was glazed with galzing powder was lowest in view of SEM, but it revealed higher surface roughness Ra value than group 1, the glazed surface and group 8, polished by diamond polishing paste, due to surface waveness. 5. Proper surface smoothness could not be in the surface roughness analysis of SEM and profilometer by Shofu laminate polishing kit composed of Diamond point, Durawhite stone and Ceramiste points. Based on the results of this study, the following conclusions can be drawn. We obtain low surface roughness than glazed surface by polishing instruments, but not perfect results clinically. In order to obtain a perfect clinical result or a surface smoothness comparable to glazed porcelain there is a need for further improvement of porcelain materials, condensa-tion techniques, polishing instruments and polishing methods. Furthermore card should be taken not to breakdown the glazed surface during the clinical and laboratory procedure.

• 한국기계가공학회지
• /
• 제5권1호
• /
• pp.33-38
• /
• 2006

Silicon has been widely used in electronic parts as a semiconductor equipment. It, however, requires much effort to grind without microcrack and chipping because of its high hardness and brittleness. So far, many studies for the grinding of engineering ceramics have been done, but not for the grinding of silicon. In this paper, a theoretical analysis on the grinding forces is introduced. Grinding experiments were performed at various grinding conditions including grinding directions (Up grinding and Down grinding), table speeds and depth of cuts. The grinding forces were measured to compare at various grinding conditions. The experimental values agree well with theoretical ones.