• The Korean Journal of Ceramics
• /
• 제3권1호
• /
• pp.29-33
• /
• 1997

Four diamond films were deposited by the microwave plasma assisted chemical vapor deposition method varying CH4 concentration from 2.5 to 10% in the feeding gases. Thermal conductivity was measured on these free standing films by the steady state method from 80 K to 400K. They showed higher thermal conductivity as the film deposited with lower methane concentration. One exception, 7.79% methane concentration deposited film, was observed to be the highest thermal conductivity. Phonon scattering processes were considered to analyze the thermal conductivity with the full Callaway model. The grain size and the concentration of the extended and the point defects were used as the fitting parameters. Microstructure of diamond films was investigated with the scanning electron microscopy and Raman spectroscopy.

• 한국전기전자재료학회논문지
• /
• 제21권11호
• /
• pp.973-976
• /
• 2008

In addition to its similarity to genuine diamond film, diamond-like carbon (DLC) film has many advantages, including its wide band gap and variable refractive index. In this study, DLC films were prepared by the RF PECVD (Plasma Enhanced Chemical Vapor Deposition) method on silicon substrates using methane ($CH_4$) and hydrogen ($H_2$) gas. We examined the effects of the RF power on the electrical properties of the DLC films. The films were deposited at several RF powers ranging from 50 to 175 W in steps of 25 W. The leakage current of DLC films increased at higher deposition RF power. And the resistivities of DLC films grown at 50 W and 175 W were $5\times10^{11}$ ${\Omega}cm$ and $2.68\times10^{10}$ ${\Omega}cm$, respectively.

• 한국표면공학회지
• /
• 제42권5호
• /
• pp.216-219
• /
• 2009

A surface acoustic wave (SAW) filter structure was fabricated employing $4{\mu}m$ thick nanocrystalline diamond (NCD) and $2.2{\mu}m$ thick ZnO films on Si wafer. The NCD film was deposited in an $Ar/CH_4$ gas mixture by microwave plasma chemical vapor deposition method. The ZnO film was formed over the NCD film in an RF magnetron sputter using ZnO target and $Ar/O_2$ gas. On the top of the two layers, copper film was deposited by the RF sputter and inter digital transducer (IDT) electrode pattern (line/space : $1.5/1.5{\mu}m$) was defined by the photolithography including a lift-off etching process. The fabricated SAW filter exhibited the center frequency of 1.66 GHz and the phase velocity of 9,960 m/s, which demonstrated that a giga Hertz SAW filter can be realized by utilizing the nanocrystalline diamond thin film.

• 한국전기전자재료학회논문지
• /
• 제19권8호
• /
• pp.701-706
• /
• 2006

In addition to its similarity to genuine diamond film, diamond-like carbon (DLC) film has many advantages, including its wide band gap and variable refractive index. In this study, DLC films were prepared by the RF PECVD (Plasma Enhanced Chemical Vapor Deposition) method on silicon substrates using methane $(CH_4)$ and hydrogen $(H_2)$ gas. We examined the effects of the post annealing temperature on the structural variation of the DLC films. The films were annealed at temperatures ranging from 300 to $900^{\circ}C$ in steps of $200^{\circ}C$ using RTA equipment in nitrogen ambient. The thickness of the film and interface between film and substrate were observed by surface profiler, field emission scanning electron microscopy (FESEM), high resolution transmission electron microscopy (HRTEM), respectively. Raman and X-ray photoelectron spectroscopy (XPS) analysis showed that DLC films were graphitized ($I_D/I_G$, G-peak position and $sp^2/sp^3$ increased) ratio at higher annealing temperature. The variation of surface as a function of annealing treatment was verified by a AFM and contact angle method.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.526-529
• /
• 2002

We studied the nematic liquid crystal (NLC) aligning capabilities by the UV alignment method on a diamond like carbon (DLC) thin film surface. A good LC alignment by UV exposure on the DLC thin film surface at $200\AA$ of layer thickness was achieved. Also, a good LC alignment by the UV alignment method on the DLC thin film surface was observed at annealing temperature of $180^{\circ}C$. However, the alignment defect of the NLC was observed above annealing temperature of $200^{\circ}C$. Consequently, the good thermal stability of LC alignment by the UV alignment method on the DLC thin film surface can be achieved.

• 한국전기전자재료학회논문지
• /
• 제17권7호
• /
• pp.760-763
• /
• 2004

We studied the nematic liquid crystaL(NLC) aligning capabilities using the new alignment material of a nitrogenated diamond-like carbon(NDLC) thin film. The NDLC thin film exhibits high electrical resistivity and thermal conductivity that are similar to the properties shown by diamond-like carbon (DLC) thin films. The diamond-like properties and nondiamond-like bonding make NDLC an attractive candidate for applications. A high pretilt angle of about 9.9$^{\circ}$ by ion beam(IB) exposure on the NDLC thin film surface was measured. A good LC alignment is achieved by the IB alignment method on the NDLC thin films surface at annealing temperature of 200 $^{\circ}C$. The alignment defect of the NLC was observed above annealing temperature of 250 $^{\circ}C$. Consequently, the high pretilt angle and the good LC alignment by the IB alignment method on the NDLC thin film surface can be achieved.

• 한국표면공학회지
• /
• 제46권1호
• /
• pp.29-35
• /
• 2013

The effect of DC bias on the growth of nanocrystalline diamond films on silicon substrate by microwave plasma chemical vapor deposition has been studied varying the substrate temperature (400, 500, 600, and $700^{\circ}C$), deposition time (0.5, 1, and 2h), and bias voltage (-50, -100, -150, and -200 V) at the microwave power of 1.2 kW, working pressure of 110 torr, and gas ratio of Ar/1%$CH_4$. In the case of low negative bias voltages (-50 and -100 V), the diamond particles were observed to grow to thin film slower than the case without bias. Applying the moderate DC bias is believed to induce the bombardment of energetic carbon and argon ions on the substrate to result in etching the surfaces of growing diamond particles or film. In the case of higher negative voltages (-150 and -200 V), the growth rate of diamond film increased with the increasing DC bias. Applying the higher DC bias increased the number of nucleation sites, and, subsequently, enhanced the film growth rate. Under the -150 V bias, the height (h) of diamond films exhibited an $h=k{\sqrt{t}}$ relationship with deposition time (t), where the growth rate constant (k) showed an Arrhenius relationship with the activation energy of 7.19 kcal/mol. The rate determining step is believed to be the surface diffusion of activated carbon species, but the more subtle theoretical treatment is required for the more precise interpretation.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1994년도 제6회 학술발표회 논문개요집
• /
• pp.98-101
• /
• 1994

white diamond thin film, which should be compposed of almost ppure diamond, could be successfully obtained under high ppressure conditions(above 150 Torr) by means of MppECVD(microwave pplasma enhanced chemical vappor depposition, ASTeX 1.5 kW). Characteristics of the films with varing expperimental pparameters have been examined. From the expperimental results, we will discuss the surface morpphology and the growth mechanism of the films.

• 한국진공학회지
• /
• 제13권4호
• /
• pp.157-163
• /
• 2004

라디오파 플라즈마 화학증착법 (radio frequency plasma assisted chemical vapor deposition: r.f.-PACVD) 법으로 증착된 다이아몬드성 카본 (Diamond-like Carbon : DLC) 필름에서 나타나는 습도에 따른 압축 잔류 응력의 변화 거동을 체계적으로 조사하였다. 합성에 사용된 탄화수소 가스의 종류와 -100V에서 -800V 범위의 기판 바이어스 전압의 조절을 통해 폴리머성 필름에서 흑연성 필름까지 광범위한 구조의 DLC 필름을 합성하였다. 상대습도가 10％-90％ 범위에서 변화하는 분위기 챔버 내에서 박막의 잔류응력의 변화를 실시간으로 측정하였다 박막의 경도와 잔류응력이 최고 값을 가지는 합성조건에서 얻어진 치밀한 DLC박막에서는 습도에 따른 잔류응력의 변화가 관찰되지 않았다. 그러나, 폴리머상이나 흑연상의 박막에서는 두 경우 모두 습도가 높아짐에 따라 압축 잔류응력이 증가함을 관찰할 수 있었으며, 습도의 변화에 대해 잔류응력이 즉각적으로 변화하였다. 한편, 동일한 습도에서 압축 잔류응력의 증가량은 필름의 두께에 반비례하는 것이 관찰되었다. 이 결과는 물분자가 필름의 구조내로 침투하면서 생기는 변화가 아니라, 박막의 표면에서 일어나는 물분자와의 반응에 의해 필름의 잔류응력이 변할 수 있음을 의미한다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.58-58
• /
• 1999

The diamond films which can be applied to SOD (silicon-on-diamond) structure were deposited on Si(100) substrate using CO/H2 CH4/H2 source gases by microwave plasma chemical vapor deposition(MPCVD), and SOD structure have been fabricated by poly-silicon film deposited on the diamond/Si(100) structure y low pressure chemical vapor deposition(LPCVD). The phase of the diamond film, surface morpholog, and diamond/Si(100) interface were confirmed by X-ray diffraction(XRD), scanning electron microscopy(SEM), atomic force microscopy(AFM), and Raman spectroscopy. The dielectric constant, leakage current and resistivity as a function of temperature in films are investigated by C-V and I-V characteristics and four-point probe method. The high quality diamond films without amorphous carbon and non-diamond elements were formed on a Si(100), which could be obtained by CO/H2 and CH4/H2 concentration ratio of 15.3% and 1.5%, respectively. The (111) plane of diamond films was preferentially grown on the Si(100) substrate. The grain size of the films deposited by CO/H2 are gradually increased from 26nm to 36 nm as deposition times increased. The well developed cubo-octahedron 100 structure nd triangle shape 111 are mixed together and make smooth and even film surface. The surface roughness of the diamond films deposited by under the condition of CO/H2 and CH4/H2 concentration ratio of 15.3% and 1.5% were 1.86nm and 3.7 nm, respectively, and the diamond/Si(100) interface was uniform resistivity of the films deposited by CO/H2 concentration ratio of 15.3% are obtained 5.3, 1$\times$10-9 A/cm, 1 MV/cm2, and 7.2$\times$106 $\Omega$cm, respectively. In the case of the films deposited by CH4/H2 resistivity are 5.8, 1$\times$10-9 A/cm, 1 MV/cm, and 8.5$\times$106 $\Omega$cm, respectively. In this study, it is known that the diamond films deposited by using CO/H2 gas mixture as a carbon source are better thane these of CH4/H2 one.