• Journal of the Optical Society of Korea
• /
• v.20 no.2
• /
• pp.300-304
• /
• 2016

A dual loop optoelectronic oscillator (OEO) based on an acousto-optic modulator (AOM) for single mode operation with an acousto-optic delay line is demonstrated in this paper. When the OEO operates, the free spectral range is a function of the total loop length of the OEO, which is mainly dependent on the propagation time of the acoustic wave in the AOM. Due to the huge difference in the magnitude between the speed of light and the acoustic velocity in the AOM, the effective loop length converted to light-propagation length of the OEO increases to 3.8 km. With 150 MHz oscillation frequency, phase noise of -118 dBc/Hz at 10 kHz frequency offset, and -140 dBc/Hz at 200 kHz frequency offset, is achieved.

• Journal of computational fluids engineering
• /
• v.17 no.4
• /
• pp.24-31
• /
• 2012

Effects of the subgrid length-scale in the Delayed-Detached Eddy Simulation(DDES) are investigated based on the Spalart-Allmaras(S-A) and the k-$\omega$ Shear Stress Transport(SST) turbulence models. Driver & Seegmiller's experimental results are used to validate numerical results. Grid convergence with grid resolution and subgrid length-scale is investigated. The simulation results show that the volume method for the subgrid length-scale is more resistant to unfavorable effects of the grid size in the periodic direction than the maximum method. Using a sufficient grid resolution and an appropriate subgrid length-scale, both S-A based DDES and SST based DDES methods can provide a good correlation with the experimental data.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.52 no.4
• /
• pp.389-399
• /
• 2019

This study is designed to observe the development of skeleton of Sakhalin sole Limanda sakhalinensis in order to use the findings as the basic data for the taxonomic research. As for the development of skeleton, on 20 days of the hatch when its average total length was 5.86 mm, the clavicle and the paraspenoid in the cranium were ossified. As for the jaw bone, the premaxillary and the dentary were ossified. On 28 days of hatch when its total length was 7.05 mm, 25 neural spines and 22 hemal spines were ossified and 5 fin rays appeared. On 34 days of hatch when its average total length was 8.40 mm, the end of tail was twisted by $45^{\circ}$ and 3 hypural bones were ossified. On 48 days of hatch when its average total length was 10.1 mm, 2 actinosts below the postcleithrum were ossified. On 54 days of hatch, when the average total length was 10.4 mm, the ethmoid, prootic and exoccipital were ossified, thus completing the ossification of skeleton.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.22 no.1
• /
• pp.99-112
• /
• 2020

A edible mushroom, Hypsizygus marmoreus is commercially cultivated. However, the researches of cultivation and physiological characteristics were not conducted in Korea. In this study, we conducted on artificial cultivation of H. marmoreus and elucidated the effect of light on the mycelial growth and fruit body development using LED light sources with different wavelength; blue (peak wave length 460nm), green(peak wave length 530nm), yellow(peak wave length 590nm), red(peak wave length 630nm), and white as positive control. Mycelial growth of H. marmoreus strains were inhibited about 30~40% in inhibition ratio under the illumination with blue, green, yellow LED light. However, red LED light was not inhibited. Elongation of stipe was effective under the long wave length such as yellow and red light. Abnormal fruit body was produced under the long wavelength and dark. However, development of pileus was effective under the short wavelength such as green and blue light. Also, as a result of cultivation with mixed light for high quality and harvest, many effective numbers and yields of fruiting bodies were obtained in the mixed treatment of blue and white light, and pileus developed well.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.53 no.2
• /
• pp.203-208
• /
• 2020

This study was carried out to clarify the larvae and juveniles of egg development and autonomous development of Hemibarbus longirostris from Korea, and to obtain basic data for species conservation and seed production. The shape of the egg was circular and sticky. The average size of the eggs was 2.01 mm (n=10). At 185 hours after fertilization, more than 50% of the total embryos were hatched. The newly hatched larvae had an average total length of 8.10 mm (n=5) and had egg yolk in the abdomen. At 3 days after hatching, the larvae absorbed all egg yolk was average total length 8.64 mm. On the 6 days after hatching, the caudal tip of the notochord started to curve upwards was average total length 10.9 mm. At 70 days after hatching, the average total length 37.9 mm. The number of fins was i 8-10 in dorsal fin, iii 7 in the anal fin, and ii 5 in the ventral fin.

• Computers and Concrete
• /
• v.8 no.4
• /
• pp.465-472
• /
• 2011

This paper investigates bond behavior of structural lightweight concrete (SLWC) and ordinary concrete (OC) comparatively using bending test called Standard Belgium Hinged Beam Test (SBHBT). For this purpose the experiments were carried out as three series on 36 beam specimens (12 specimens of SLWC and OC with $20{\phi}$ development length, 12 specimens of SLWC with $25{\phi}$ development length). For each series bond behavior of steel rebars with 8, 10, 12, 14 mm diameters were tested. The results indicate that bond strength of SLWC is considerable lower than OC and $20{\phi}$ development length is insufficient for steel rebars with 12 mm and 14 mm diameters. Therefore development length of SLWC was extended to $25{\phi}$, even if 8 and 10 mm steel rebars provided acceptable bond strength. In this way, bond strength between SLWC and 8 and 10 mm steel rebars was developed. In addition, adequate bond behavior was achieved for 12 mm rebar but the beam in which 14 mm rebar used exceeded their bearing capacity by shear forces before yield stress. This result shows that SBHBT is more convenient for small sized steel rebars.

• Computers and Concrete
• /
• v.26 no.6
• /
• pp.587-593
• /
• 2020

In this study, bond behavior of ordinary concrete and rebars with different diameters and development length was investigated by using Hinged Beam Test (HBT) and Eccentric Pull-Out Test (EPT) comparatively. For this purpose, three different rebar size and development length depending on rebar diameter were chosen as variables. Three specimens were produced for each series of specimens and totally 54 specimens were tested. At the end of the tests it was observed that obtained results for both tests were quite similar. On the other hand, increased bar size, especially for the specimen with 14 mm bar size and 14 development length (lb), caused shear failure of test specimens. This situation infers that when bigger bar size and lb are used in such test, dimensions of test specimens should be chosen bigger and stirrups should be used for producing of test specimens to obtain more adequate result by preventing shear failure. Also, a nonlinear regression analysis was employed between HBT and EPT results. There was a high correlation between the EPT values, lb, rebar diameters and estimated theoretical HBT. In addition, at the end of the study an equation was suggested to estimate bond strength for HBT by using EPT results.

• Journal of the Korean Society of Costume
• /
• v.42
• /
• pp.163-172
• /
• 1999

The purpose of this study is to classify the types of torso of adult females using the tight fitting technique and pattern development figure. The subjects are 106 females of 19 to 24 years old. 59 different items are measured from body surface development and analyzed by factor analysis and cluster analysis. The results are as follows; 1. Eight somatotype factors are obtained through factor analysis and orthogonal rotation by the method of Varimax Factor 1 is the length of upper body factor 2 the length of lower body factor 3 the circumference and width of the back of upper body factor 4 the circumference and width of front torso factor 5 the dart type of the back of upper body factor 6 the size of the back neck factor 7 the type of the front shoulder and factor 8 the size of the back arm hole. 2. As a result of cluster analysis the somatotype of torso is classified into 5 types. Type 1 is normal in length circumference and width of upper body. Type 2 is shortest length circumference and width of torso. Type 3 is long in length circumference and width of torso. Type 4 is normal length and short in circumference and width especially short in bust circumference. Type 5 is longest in length circumference and width of torso.

• Development and Reproduction
• /
• v.2 no.1
• /
• pp.69-74
• /
• 1998

The early gonadal development and sexual differentiation of Rhynchocypris oxycephalus are described from the stage of hatching to 150 days after hatching. During this peroid, the average length of the body grew from 0.64 cm to 5.96 cm. the primordial germ cells (PGCs), which could be recognized at the time of hatching, began to protrude into peritoneal cavity at a standard total length of 1.91 cm. At a standard total length of 2.29cm, initial ovarian differentiation wasidentified by the transformation of PGCs to meiotic oocytes. Finally, at the standard total length of 5.96 cm, the female gonads gradually developed towards migratory nucleus oocytes, characterisiing the maturation. Oocytes proliferated rapidly after sex differentiation while the testis entered a period of quiescence, as they continued to multiply but did not undergo growth until the standard total length of 4.00 cm. At a standard total length of 4.00 cm, spermatocytes arrested in thephase of interkinesis, Sertoli-like cells and sperm duct formation, with signs of meiotic activity, were observed. Therefore it may be concluded that R. oxycephalus belongs to the differentiated type of gonochoristic teleosts.

• Journal of the Korean Society of Costume
• /
• v.45
• /
• pp.17-28
• /
• 1999

This study was to analyze factors of the body form and factors of bodice pattern through a surface developement figure for the tight bodice pattern design. Fifty replicas of the trunk surface were made by applying a surgical tape method of female subjects between 18 and 24 years old. The result was as follows: 1. The gaps between direct measurements and measurements of the surface development figure were regarded as allowances for the tight bodice pattern. 2. There are four factors of body form selected by factor analysis. The 1st factor signifies th degree of fatness in the upper body. The 2nd factor signifies the length of the upper body. The 3rd factor signifies the part of the front shoulder. The 4th factor signifies the part of the neck. 3. There are high correlations between center back line of the surface development figure and back length line side line front length line back neck depth back upper chest depth. There are high correlations between back bust line of the surface development figure and back interscye breadth line back upper chest line back armhole line. There are high correlations between front bust line of the surface development figure and front upper chest line front interscye breadth line front armhole line front neck breadth 4. The regression expressions of measurements of the surface development figure of the upper body were analyzed as(Fig. 3).