• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1746-1749
• /
• 1997

A distributed optical fiber temperature sensor can continually monitor the measurand at every point along of its fiber length. It is based on OTDR technics which used extreamlly weak backward scattered light called Raman scattering. When the Pulsed high intensity laser light injected into the optical fiber there are several kind of backscattered light such as Rayleigh, Stokes, and anti-Stokes, etc. caused by impurities molecular vibrations. The temperature distribution is derived form the intensity ratio Raman scatted light-Stokes versus anti-Stokes-and the time function between light injection and signal detection. It is shown that the priniciple of distributed sensing, the system desing, and the result of experiments.

• Computational Structural Engineering
• /
• v.1 no.1
• /
• pp.95-102
• /
• 1988

I-BUILDS is the building design expert system conceptually modeled for synthesizing the conventional CAD programs (BUILDS; an integrated BUILding Desing System) and the knowledge base into an unified system. As a part of the efforts to build this system, this paper presents the conceptual model by which the data items generated by inference are transformed into a formatted input file to be used for several BUILDS subsystems, each of which is assigned to have various computational capabilities and to perform specialized task.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2006.05a
• /
• pp.805-808
• /
• 2006

현재 국내에서 웹을 기반으로 한 e-learning 콘텐츠는 많이 개발되고 있으나 이들 대부분이 매뉴얼 식으로 제작되어 멀티미디어 형식만 빌려 텍스트 형태로만 구성하는 방식이 주를 이루고 있는 실정이다. 따라서 본 논문에서는 SMIL을 기반으로하여 멀티미디어 아날로그와 디지털 자료를 융합할 수 있는 핵심 기술을 제안하며, 이를 웹 상에서 창의적이고, 자기주도적으로 개인차에 따라 학습 속도를 조절할 수 있는 프로젝트 학습기법을 국내 교육환경에 맞게 교수-학습 이론을 적용하여 설계 구현하였다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.367-370
• /
• 1999

An experimental study was carried out to estimate development lengths of the prestressing strand in pretensioned beams. Recent studies had indicated that current desing provision were inadequate. Objective of this investigation is to determine the effect of strand diameter and concrete cover in pretensioned beams. Strand of the 1.52cm diameter is more useful and economic than that of the 12.7mm diameter, but current provision does not include 15.2mm diameter strand in experimental data. Because the property of strand has been developed, current provision need to be improved. Based on the experimental data, it was determined that bond failure would be prevented if no cracking occured in transfer zone of a pretensioned strand.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.815-822
• /
• 1999

This program is developed to design Prestressed Concrete Cylinder Pipes (PCCP), Fittings and Thurst Blocks and to manage drawings, quantity calculations and calculation data, using Graphic User Interface(GUI), which is capble of not only reducing the time taken to design, but also enabling the user to achieve such a design even when operator has no theoretical knowledge of that design while only having knowledge of data inputting and outputting. PCCP is used in water transmission popeline of the Great Man-made River Project. In domestic area, PCCP is used for water cooling systems of Uljin and Youngkwang nuclear power. In abroad, especially in the United States and Canada PCCP applies virtually every metropolitan area with raw and treated water.

• Journal of Advanced Marine Engineering and Technology
• /
• v.10 no.4
• /
• pp.31-40
• /
• 1986

With the tendency toward high speed and high pressure in centrifugal pumps, the problem of sub-synchronous vibration has arisen, caused by the hydraulic forces of the working fluid, such as wearring, balance piston, impeller, etc.. These forces can drastically alter the rotor critical speeds and stability characteristics, and can be acted significant destabilizing forces. For preventing such self-excited vibration, the desing of the rotor system needs, which would secure the stability of the machine. In this paper, a procedure is presented for dynamic modeling of rotor-bearing-seal-impeller systems which consist of rigid disks, distributed parameter finite rotor elements and discrete bearings, seals and impellers. A finite element model including the effects of rotatory inertia and gyroscopic moments is developed using the consistent matrix approach. The technique of dynamic matrix reduction is applied to the shaft matrices to reduce them to a set of matrices of dynamic of significantly fewer degrees of freedom. The representation of bearing, seal and impeller elements is in term of linearized stiffness and damping matrices by reasonably small perturbations from equilibrium. The stability behavior of a typical double suction centrifugal pump is presented. Results show the influence of clearance and flow conditions on running speeds and stability characteristics.

• Journal of Advanced Marine Engineering and Technology
• /
• v.10 no.4
• /
• pp.67-77
• /
• 1986

The information on the heat transfer characteristics, flow pattern and pressure drop, are very important for the desing of general heat exchanger, refrigerating system, air conditioning system and energy recovery system. In these systems, water or lubricating oil contained in working fluid affects greatly the flow and heat transfer condition and this phenomena must be considered in the practical design. An experiment has been performed for studying the flow and heat transfer characteristics of the forced convective horizontal flow of R-113 under the range of the liquid single phase state to the boiling flow state. Basic experimental results are obtained in the case that water or lubricating oil does not contaminate in the test fluid. Experimental results are as follows; (1) The local heat transfer coefficients in the nucleate boiling region and transition boiling region are almostly ten times as large as that of liquid single phase flow. (2) The measured heat transfer coefficient in the present experimental range is relatively agreed well with the predicted value from the various experimental results for the boiling flow.

• Journal of the Korea Furniture Society
• /
• v.10 no.1
• /
• pp.83-93
• /
• 1999

The purpose of this study is to analyze the issues of today's school furniture systems and propose the new standards for tomorrow's school furniture design. For the improvement of the educational environments, the school furniture need to be reformed very badly. The present educational furniture is very falling behind in safety, function, ergonomics and its aesthetics. The classroom tables and chairs should be comfortable in physical and psychological aspects and accommodates the practical use in order to raise the student's efficiency of learning. In this study, the new design and ergonomic standards of the chairs and tables are proposed by comparing other national standards and analyzing the problems of the present educational facilities.

• Journal of Korean Society for Quality Management
• /
• v.28 no.4
• /
• pp.119-139
• /
• 2000

In order to examine the determinants of new product success, 217 winning products in Korean market are analyzed with a focus on merchantability. For the purpose of the analysis, dimensions of products are classified into function, aesthetics, economy, safety, usability, reliability, brand image, assurance, distribution channel, advertisement, DFE(desing for the environment). The major dimensions of sinning products were identified for each category of the products. The results this study would be a cue to the future direction of new product development.

• Journal of Astronomy and Space Sciences
• /
• v.12 no.1
• /
• pp.54-65
• /
• 1995

We present a design study for a remote sensing camera system which can be operated in multi-channel mode simultaneously with several bandpass filters. The camera control electronics is based on the multiplexed driving concept, which can provide a variety of flexibility for system control parameters and its individual optimisation. The design can also be applied to any system with linear sensors or frame sensors according to its functional requirements. The system design parameters have been examined, including modification of driving waveforms for different types of sensors, waveforms for low-nosie readout circuit in analog chain, and synchronisation with other signal processing.