• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.30 no.2
• /
• pp.26-30
• /
• 2016

This paper presented an optimum design of a perpendicular PMDSLSM (Permanent Magnet Double-sided Linear Synchronous Motor) to minimize the detent force. As an optimum method, the response surface method was used and 3D finite element method for the calculation. The design variables of the machine were the primary core width and thickness, and magnet width, thickness and length. Object functions were to minimize the detent force and maximize the thrust of the basic model. The results showed that the thrust force of the optimum design increased from 82.1N to 90.2N and detent force decreased from 15.2N to 2.8N, respectively, compared to the basic model.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.1
• /
• pp.73-79
• /
• 2004

When structures undergo rotating motion, their modal characteristics often vary significantly. The variations of modal characteristics are determined from their geometric shapes and their rotating angular speed. Since the modal characteristics vary during the operation of the structures, they should be carefully scrutinized. In this paper, rotating cantilever beams are chosen as design targets which need to meet some specific design requirements. The thickness and the width of the rotating beams are assumed as multi-stage spline functions and the stage values for the thickness and the width are used as design variables for the optimization problems.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.551-554
• /
• 2005

This study uses a characteristic function to explain correlations between the objective function and design variables. Analysis of means and table of orthogonal array were carried out. The change of shape of diaphragm, thickness of diaphragm and voice coil weight based on the table of orthogonal array is made. Therefore this study carried to decide shape of diaphragm, voice coil weight and thickness of diaphragm for minimizing 1st natural frequency and maximizing 2nd natural frequency of diaphragm using design of experiments and characteristic function with constraints. we showed improved design factors that minimized 1st natural frequency and maximized 2nd natural frequency of diaphragm.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.1
• /
• pp.67-73
• /
• 1999

This paper presents resizing design optimization method by utilizing genetic algorithm(GA), which consists of three basic operators : reproduction, crossover and mutation. The fitness and penalty function for resizing optimization problem are defined, and the flowchart of the developed computer program along with the descriptions of each modules is presented. Also, modelling for flexible-body dynamic analysis is presented. The model is composed of bodies, joints, and force elements such as translational spring-damper-actuator. The design objects si to determine the wall thickness for minimum weight under dynamic displacement constraint.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1999.04a
• /
• pp.78-85
• /
• 1999

In this study, I-type girders used as main members of a two span continuous steel bridge, are optimally designed by a Load and Resistance Factor Design method(LRFD) using an numerical optimization method. The width, height web thickness and flange thickness of the main girder are set as design variables, and light weight design is attempted by choosing the cross-sectional area as an object function. The main program is coded with C++ and connected with optimization modul ADS, which is coded with FORTRAN. The results of the program show that the stress constraints of noncomposite section during the initial construction stage become active in the positive moment area and the service limit state constaints become active in the negative moment area.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.9
• /
• pp.782-787
• /
• 2008

First, the effect of the geometry such as the curved shape of the struts composing the truss structure of WBK is elaborated. Then, analytic solutions for the material properties of WBK and the maximum loads of a WBK-cored sandwich panel under bending are derived. A design optimization with the face sheet thickness and the core height selected as the design variables is presented for given slenderness ratios of the WBK core. Unless the face sheet thickness is limited, the optimal design to give the maximum load per weight is always found at a confluence of three failure modes, namely, face sheet yielding, indentation plastic, and core shear modeB plastic.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.638-642
• /
• 2003

This paper presents a parameter design of an Electrorheological(ER) panel for noise reduction using Taguchi method. Taguchi method is a robust design method that determines control parameters in the presence of noise effect. Host structure thickness, spacer thickness, base oil viscosity and the weight ratio of ER particles are chosen for the control factors. A test setup in an SAE J1400 facility is used to analyze the sound transmission loss. The sensitivity of each factor with signal-to-noise(S/N) ratio and analysis of variance are investigated. The analysis results show that the weight ratio of ER particle and base oil viscosity of the ER fluid mostly affects the noise reduction in the presence of electric field. Based on the Taguchi method, an optimal configuration was designed and comparison is made with experimental result fer the verification.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.684-689
• /
• 2003

When structures undergo rotating motion, their modal characteristics often vary significantly. The variations of modal characteristics are determined from their geometric shapes and their rotating angular speed. Since the modal characteristics vary during the operation of the structures, they should be carefully scrutinized. In this paper, rotating cantilever beams are chosen as design targets which need to meet some specific design requirements. The thickness and the width of the rotating beams are assumed as multi-stage spline functions and the stage values for the thickness and the width are used as design variables for the optimization problems.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1061-1064
• /
• 2006

Optimal design of functionally graded plates is investigated considering stress and critical temperature. Material properties are assumed to be temperature dependent and varied continuously in the thickness direction. The effective material properties are obtained by applying linear rule of mixtures. The 3-D finite element model is adopted using an 18-node solid element to analyze more accurately the variation of material properties and temperature field in the thickness direction. For stress analysis, the tensile stress ratio and compressive stress ratio of the structure under mechanical load are investigated. In the thermo-mechanical buckling analysis, temperature at each node is obtained by solving the steady-state heat transfer problem and Newton-Raphson method is used for material nonlinear analysis. Finally, the optimal design of FGM plates is studied for stress reduction and improving thermo-mechanical buckling behavior, simultaneously.

• Journal of information and communication convergence engineering
• /
• v.8 no.4
• /
• pp.449-452
• /
• 2010

We have analyzed channel doping and dimensions(channel length, width and thickness) for the optimum subthreshold characteristics of DG(Double Gate) MOSFET based on the model of MicroTec 4.0. Since the DGMOSFET is the candidate device to shrink short channel effects, the determination of design rule for DGMOSFET is very important to develop sub-100nm devices for high speed and low power consumption. As device size scaled down, the controllability of dimensions and oxide thickness is very low. We have analyzed the short channel effects for the variation of channel dimensions, and found the design conditions of DGMOSFET having the optimum subthreshold characteristics for digital applications.