• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1991.10a
• /
• pp.5-14
• /
• 1991

The basic rules and principles for designing structures with composite materials are briefly and intensively presented. The proposed design steps are explained. For preliminary design, use of quasi-isotropic properties is proposed. The validity of this proposal will be reported by separate papers.

• Journal of the Institute of Convergence Signal Processing
• /
• v.8 no.3
• /
• pp.222-226
• /
• 2007

In this paper we composed the dual fuzzy rules using each region of specific points and $e-{\Delta}e$ phase plane In order to make dual fuzzy rule base. We composed the fuzzy control rules which can decrease rise time, delay time, maximum overshoot than basic fuzzy control rules. proposed method is alternately use at specific points of $e-{\Delta}e$ phase plane with two fuzzy control rules that is one control rule occruing the steady state error in transient region and another fuzzy control rule use to decrease the steady state error and rapidly converge at the convergence region. Also, two fuzzy control rules in the $e-{\Delta}e$ phase plane decide the change time according to response characteristics of plants. In order to confirm thef proposed algorithm. As the results of experiments through the hydraulic servo motor control system with a DSP processor, We verified that proposed dual fuzzy control rules get the good response compare with the basic fuzzy control rule.

• Earthquakes and Structures
• /
• v.10 no.1
• /
• pp.211-238
• /
• 2016

The Maximum seismic responses of steel buildings with perimeter moment resisting frames (MRF), modeled as complex MDOF systems, are estimated for several incidence angles of the horizontal components and the critical one is identified. The accuracy of the existing rules to combine the effects of the individual components is also studied. Two and three components are considered. The critical response does not occur for principal components and the corresponding incidence angle varies from one earthquake to another. The critical response can be estimated as 1.40 and 1.10 times that of the principal components, for axial load and interstory shears, respectively. The rules underestimate the axial load but reasonably overestimate the shears. The rules are not always inaccurate in the estimation of the combined response for correlated components. On the other hand, totally uncorrelated (principal) components are not always related to an accurate estimation. The correlation of the individual effects (${\rho}$) may be significant, even for principal components. The rules are not always associated to an inaccurate estimation for large values of ${\rho}$, and small values of ${\rho}$ are not always related to an accurate estimation. Only for perfectly uncorrelated harmonic excitations and elastic analysis of SDOF systems, the individual effects of the components are uncorrelated and the rules accurately estimate the combined response. The degree of correlation of the components, the type of structural system, the response parameter under consideration, the location of the structural member and the level of structural deformation must be considered while estimating the level of underestimation or overestimation.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2015.09a
• /
• pp.46-49
• /
• 2015

Common Structural Rules (CSR) about bulk carriers and double-hull oil tankers of International Association of Classification Societies (IACS) has been applied to ships contracted for construction since April 2006. By unifying each society's rules, the difference of opinion in the between shipyard and ship owners, classification was reduced, and CSR has been evaluated by rules the safety structure more enhanced. However, The CSR about the bulk carriers and double hull oil tankers, important design content standards, such as the local scantling calculation, static/dynamic load case and corrosion margin and etc., are different. Therefore in order to combine the CSR, the Harmonized CSR for bulk carriers and double hull oil tankers (H-CSR) was issued on 1, January, 2014, and will be apply to ships contracted for construction after 1st July 2015. It is necessary to verify the H-CSR to optimize the structural arrangement because effective date is not far off. In this study, we compared the impact by rule change for the hull girder shear strength of bulk carriers between CSR and H-CSR in respect of the yielding and buckling strength.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.214-218
• /
• 1995

Much labor, an exceedingly long lead time, and the skills of experienced engineers are required for press tool design. To reduce such problems, several CAD systems for blanking or piercing have been developed. This paper describes a computer-aided design for blanking or piercing of irregularly shaped sheet metal products. An approach to the system is based on knowledge base rules. The process planning & die design system is designed by considering several factors, such as complexity of blank geometry, punch profile, and availability of press equipment and standard parts. Therefore, after checking a production feasibility for irregular shaped sheet metal products, this system which is implemented strip layout module can carry out a process planning and generate the strip layout in graphic forms. Also this system implemented die layout module can carry out a die design for each process which is obtained form the result of an automated process planning and generate parts and assembly drawing of a die set.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.1
• /
• pp.11-16
• /
• 1996

The purpose of this paper is to present a summary of assignment design values according to domestic softwood structural lumber grading rules. Allowable stresses for visually graded lumber were determined from basic data on small. clear specimens. The data corrected for variability such as natural defects and other factors. The procedure adopted by Japan was used for assigning allowable design values. Strength ratios in relation to each defect were taken from ASTM D 245-81. Korean pine(Pinus koraiensis S. et Z.), Korean red pine(Pinus densiflora S. et Z.), Japanese larch(Larix leptolepis Gordon) and Needle fir(Abies holophylla Max) were applied to this study. The calculated allowable stresses were same in Korean pine and Korean red pine. These values were highest in Japanese larch lowest in Needle fir. So, it is desirable for these species to be classified into different catagories Species Group. However, accurate comparison in design values on lumber grading rules among U.S., Japan and Korea was somewhat difficult. And full scale testing will be necessary for accurate determination of the correction factors to setting up design values.

• Korean Journal of Computational Design and Engineering
• /
• v.7 no.1
• /
• pp.9-17
• /
• 2002

The study is insufficient on process planning of the elliptical deep drawing product. Thus, in this present study, the expert system for elliptical deep drawing products was constructed by using process sequence design. The expert system was developed to be based on the general concept of each entity. The system was developed in this work consists of sixth modules. The first one is a shape recognition module to recognize non-axisymmetric products and to generate Entity_list. The second one is three dimensional (3-D) modeling module to calculate the surface area for non-axisymmetric products. The third one is a blank design module to create suggested blanks of three shapes with the identical surface area. The fourth one is shape design module based on the production rules that play the most important role in an expert system for manufacturing. The production rules are generated and upgraded by inter- viewing field engineers, plastic theory and experiments. The fifth and sixth ones are a graphic module to visualize results of the expert system and a post module to rise user's convenience, respectively. According to constructed the expert system for process sequence design, it was possible to reduce the lead time.

• Journal of Ocean Engineering and Technology
• /
• v.35 no.2
• /
• pp.161-171
• /
• 2021

For the fatigue design of offshore structures, it is essential to understand and use the S-N curves specified in various industry standards and codes. This study compared the characteristics of the S-N curves for five major codes. The codes reviewed in this paper were DNV Classification Rules (DNV GL, 2016), ABS Classification Rules (ABS, 2003), British Standards (BSI, 2015), International Welding Association Standards (IIW, 2008), and European Standards (BSI, 2005). Types of stress, such as nominal stress, hot-spot stress, and effective notch stress, were analyzed according to the code. The basic shape of the S-N curve for each code was analyzed. A review of the survival probability of the basic design S-N curve for each code was performed. Finally, the impact on the conservatism of the design was analyzed by comparing the S-N curves of three grades D, E, and F by the five codes. The results presented in this paper are considered to be a good guideline for the fatigue design of offshore structures because the S-N curves of the five most-used codes were analyzed in depth.

• Architectural research
• /
• v.21 no.1
• /
• pp.9-20
• /
• 2019

In the spatial configuration of a unit plan, two rules exist: one that governs the arrangement of spaces, and one that controls the design process of generating a unit plan. This study defines space grammar as an integration of the two rules that give birth to a given spatial configuration and as the process of the generation of unit plans. To understand the distinctive features of Indonesian row houses, this study analyzes the unit plans of row houses in new towns of the metropolitan cities of Indonesia, derives a common space grammar from the unit plans, and interprets the sociocultural background that has produced this space grammar. This study employs Seo's (2007a; 2007b) graph-theoretic methodology to analyze the spatial configurations of unit plans along with a topographical approach to systematically illustrate the design process. The guest space was found as the most unique space of Indonesian houses, which cannot be found in other Southeast Asian houses. Kitchen was clearly seperated from the dining and living spaces, following traditional custom. Dining space was found to serve as a circulation center, connecting the entrance, the lving area and the kitchen. This study locates the basic orders of primary space and the design principles that dictate the unique spatial configurations of Indonesian row houses. This study reveals the basic space grammar that underpins the forms of Indonesian row houses, explaining the sociocultural and geo-climatic factors affecting this space grammar and proposing unique characteristics of Indonesian contemporary houses.

• Proceedings of the IEEK Conference
• /
• 2001.06c
• /
• pp.229-232
• /
• 2001

Wireless Internet based in WAP(Wireless Application Protocol) has been a very useful and attractive means picking up information through service irrelavant to time and space. And more the request of user has been diverse. In this paper, we implemented a Diet Menu System using expert knowledge-based rules on the WAP environment. This enables the moving man interested in diet to get information through wireless mobil hand phone. There are only connection-oriented system for this type of service till now. This paper has designed basic expert knowledge rules for result display, verified and implemented for WAP environment.