• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.557-558
• /
• 2012

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.33-34
• /
• 2011

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.4
• /
• pp.389-395
• /
• 2014

In this study, we discussed the weight reducing of 2 MW class of wind turbine rotor shaft by optimizing design method. The optimal design was applied to obtain get an optimized structure and parameters for the base structure using FEA and DOE. The results were verified by comparing the maximum von Mises stresses and maximum volume in the case of the existing design with those in the case of the optimized design. It was shown that the weight of a base structure can be reduced by about 23 %.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.12
• /
• pp.125-132
• /
• 2013

This paper has done a three-dimensional FEM analysis of the PM claw pole stepping motor. As magnetization happens in the z-axis, which does not have a constant value, three-dimensional FEM analysis is necessary for characteristic analysis of PM claw pole stepping motors. Because it is a type of permanent magnet motor, the PM claw pole stepping motor naturally has a detent torque. This torque is known to show negative effects on motor performance. To improve motor performance, reducing the detent torque is very important during the motor design. This paper applied DOE for optimization of stator pole design of the motor. Also, we compared motor performance by applying a different type of rotor shape, dividing the permanent magnet. To verify the simulation results, an experiment was done.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.869-872
• /
• 2005

This research studied robust design of column part for LCD transfer system. $1^{st}$ DOE(Design of Experiment)was conducted to find out main effect factors. 36 experiments were performed and their results were shows that the geometric parameters(Low-length, Side-length, Upper-thickness, Middle-thickness)are more important than other factors. The main effect plots shows that the maximum deflection of column is minimized with increasing Low-length, Side-length, under-thickness and Middle-thickness. $2^{nd}$ DOE was conducted to obtain RMS(Response Surface Method)equation 25 experiments were conducted. The CCD(Central Composite Design)technique with four factors were used. The coefficient of determination $(R^2)$ for the calculated RSM equation was 0.986. Optimum design was conducted using the RSM equation Multi-island genetic algorithm was used to optimum design. Optimum value for Low-length. Side-length, Upper-thickness and Middle-thickness were 299.8mm, 180.3mm, 21.7mm, 21.9mm respectively. An approximate value of 5.054mm in deflection was expected to be a maximum under the optimum conditions. Six sigma robust design was conducted to find out guideline for control range of design parameter. To acquire six sigma level reliability, the standard deviation of design parameter should be controlled within 2% of average design value.

• Transactions of the Society of Information Storage Systems
• /
• v.6 no.1
• /
• pp.6-11
• /
• 2010

Researches for actuator which is appropriate to slim optical disk drive (ODD) have been progressed for a long time. Various types of actuators are suggested to secure high performances with slim thickness. In this paper, the slim actuator with symmetric electromagnetic (EM) circuit is suggested to apply slim ODD. Various EM circuits are proposed to increase EM force in the focusing and the tracking directions. Flexible mode frequencies and driving sensitivities are increased by using stress distribution and design of experiment (DOE). Consequently, final model is suggested to have high flexible mode frequencies and driving sensitivities.

• IE interfaces
• /
• v.22 no.1
• /
• pp.95-103
• /
• 2009

During the past few years, design of experiments (DOE) has been gaining acceptance in the telecommunications research community as a mean for designing and analyzing experiments economically and efficiently. In addition, the need for introducing a systematic robust design methodology (i.e., one of the most popular DOE methodologies) to network simulations has been increasing. In this paper, we present an architecture of voice over IP (VoIP) application and the E-Model for calculating the perceived quality of service (QoS). Then, we apply the Taguchi robust design methodology to optimize the perceived QoS of VoIP application, and describe the detailed step-by-step procedures. We have used ns-2 simulator to collect experimental data in which the SN ratio, a robustness measure, is analyzed to determine an optimal design condition. The analysis shows that "initial delay time in playout buffer" is a major control factor for ensuring robust behaviors of the perceived QoS of VoIP. Finally, we verify the proposed optimal design condition using a confirmation experiment.

• Journal of the Korean Society of Systems Engineering
• /
• v.6 no.1
• /
• pp.33-39
• /
• 2010

Anti-surface missiles have been the most dangerous threat to the surface ships, therefore analyzing the defense effectiveness of surface ships against diverse anti-surface missiles attack strategies is very important to evaluate and anticipate the naval combat ship's abilities in terms of AAW (Anti-Air Warfare). In this paper, we don't study on the defense effectiveness of a ship against a missile, but focus on the defense effectiveness for surface ships against multiple missiles specialized in strategies of anti-surface missiles; ripple fire attack and simultaneous time on target attack (STOT). So, we conduct a variety of monte-carlo simulations with high-fidelity simulators, analyze the measure of defense effectiveness for the key factors of strategies and evaluate the effects and possible interactions of several factors through the analysis of the design of experiment (DOE).

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.9
• /
• pp.103-110
• /
• 2010

This paper presents the optimized approximation of finite element modeling for a complex tool holder spindle using both DOE (Design of Experiment) with Optimal Latin Hypercube (OLH) method and approximation modeling method with Radial Basis Function (RBF) neural network structure. The complex tool holder is used for holding a (milling/drilling) tool of a machine tool. The engineering problem of complex tool holder results from the twisting of spindle of tool holder. For this purpose, we present the optimized approximation of finite element modeling for a complex tool holder spindle using both DOE (Design of Experiment) with Optimal Latin Hypercube (OLH) method (specifically a module of $iSight^{(R)}$ FD-3.1) and approximation modeling method with Radial Basis Function (RBF) (another module of $iSight^{(R)}$ FD-3.1) neural network structure

• Environmental Engineering Research
• /
• v.20 no.4
• /
• pp.392-396
• /
• 2015

This work aims to investigate the oily wastewater treatment by the electrocoagulation-flotation (ECF) and propose a mathematical model for the efficiency prediction. Cutting oil was used to prepare the synthetic oily wastewater with submicron droplet sizes. The chemical coagulation by aluminium sulfate was firstly tested following by the electrocoagulation-flotation with aluminium electrodes. Both processes gave the effective treatment performance with the efficiencies higher than 90%. However, the ECF consumed less aluminium dosage as well as produced less sludge, which were its advantage on the chemical coagulation. The performance of the ECF was found to be affected by the current density, oil concentration, and reaction time according to the analysis by the design of experiment (DOE). Finally, the prediction model was proposed by two approaches, including linear and logarithm function. The latter model gave more accuracy prediction results in terms of treatment efficiency and duration in the lag and stable stages.