• 정보저장시스템학회논문집
• /
• 제3권4호
• /
• pp.191-195
• /
• 2007

The optical disc drive has used a high NA objective lens and a shorter wavelength laser diode for high recording density. But high NA and shorter wavelength cause several margins to become short. Focusing and tracking servo has to be more accurate and active tilt compensation mechanism is also needed for coma aberration compensation. In this paper, we proposed 3-axis moving magnet type actuator. For 3-DOF motion, moving coil actuator has to be equipped with 6 wires for supplying 3 independent signals. However, moving magnet type actuator doesn't need to change the configuration of wires because coils are in stator. So, we added a tilt mechanism to the 2-axis moving magnet actuator which is designed in previous research. Addition of the tilt mechanism cuts down the focus sensitivity. So, maximization the tilting sensitivity and securing the focusing sensitivity are objectivities of this research. DOE (design of experiments) procedures of electromagnetic circuit are performed for parameter study and the optimization is also performed to maximize the tilt sensitivity. And then the final design is suggested and its performance is verified by FE simulation.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1832-1837
• /
• 2011

This paper presents the optimal permanent magnet shape on the rotor of an interior permanent magnet motor to reduce the core losses and improve the performance. As permanent magnet has conductivity inherently, it causes huge amount of eddy current losses by the slot harmonics with concentrated winding. This loss is roughly 100 times larger than that of distributed winding in high speed operation and it cannot be ignored, especially on traction motors. Each eddy current loss on permanent magnet has been investigated in detail by using FEM(Finite Element Method) instead of EMCNM(Equivalent Magnetic Circuit Network Method) in order to consider saturation and non-linear magnetic property. Simulation-based DOE(Design Of Experiment) is also applied to avoid large number of analyses according to each design parameter and consider expected interactions among parameters. Consequently, the optimal design to reduce the core loss on the permanent magnet while maintaining or improving motor performance is proposed by an optimization algorithm using regression equation derived and lastly, the core loss reduction on the proposed shape of the permanent magnet is verified by FEM.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1033-1036
• /
• 2007

The optical disc drive has used a high NA objective lens and a shorter wavelength laser diode for high recording density. But high NA and shorter wavelength cause several margins to become short. Focusing and tracking servo has to be more accurate and active tilt compensation mechanism is also needed for coma aberration compensation. In this paper, we proposed 3-axis moving magnet type actuator. For 3-DOF motion, moving coil actuator has to equip 6 wires for supplying 3 independent signals. However, moving magnet type actuator doesn't need to change the configuration of wires because coils are in stator. So, we added tilting mechanism to 2-axis moving magnet actuator which is designed in previous research. Addition of the tilting mechanism cuts down the focusing sensitivity. So, maximization the tilting sensitivity and securing the focusing sensitivity are objectivities of this research. DOE (design of experiments) procedures of electromagnetic circuit are performed for parameter study and the optimization is also performed to maximize the tilt sensitivity. And then the final design is suggested and its performance is verified by FE simulation.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.848-851
• /
• 2007

Recently, as the demand of the information storage devices with large storage capacity such as BD(Blu-ray Disk) and HDTV(high-definition television) is increased, the optical storage devices are also required to have fast data transfer rate and large storage capacity. To satisfy these requirements, the actuator for optical disk drive should have high flexible mode frequencies for system stability. In this paper, we suggested a moving magnet type actuator having high flexible mode frequency. However, the moving magnet type actuator does not have sufficient driving sensitivities due to the weight of its moving part. To improve driving sensitivities, we designed the model with the closed electromagnetic circuit for tracking direction. In addition, driving sensitivities and flexible mode frequencies were improved by using DOE(Design of Experiments) for magnetic circuit and modifying the lens holder. Consequently, it is confirmed that the designed model is satisfied with the desired specifications.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.637-640
• /
• 2005

The mechanical properties of bellows, such as the extensibility and the strength can be changed depending on the shape. For the shipbuilding material, it is favorable that the fatigue lift is long due to the elastic property and the reduction of thermal stress in piping system. Nowadays, the domestic production and design of bellows are based on the E.J.M.A Code. Therefore, the design standard is in need because of much errors and lack of detailed analysis. In this study, it is attempted to find out the optimal shape of U-type ship's bellows that is applied to design of experiment using the finite element method. The effective factors, mountain height, length, thickness, and number of mountains and the length of joint are considered and the proper values are chosen for the simulation. The number of mountains are increased, the volume increases above the standard volume and the stress obviously increases. In addition, the effect of the thickness of bellows on the stress is very large. Both of the volume and stress are decreasing at a certain lower value region.

• 한국세라믹학회지
• /
• 제49권1호
• /
• pp.66-71
• /
• 2012

In ancient Goryeo celadon, the effect of the chemical composition and ionic state of Fe on the color was evaluated by Mossbauer spectroscopy and Design of Experiment (DOE) analysis. The ancient celadon pieces excavated from the kiln sites in GangJin and Buan areas were analyzed by Mssbauer spectroscopy, chromaticity, and DOE analysis. The color of celadon was found to be mainly determined by that of glaze since variations of $L^*$, $a^*$, and $b^*$ values for the body were much smaller than those for the glaze. As $Fe^{2+}$/$Fe^{3+}$ in glaze increases, $L^*$ value increases, whereas $a^*$/$b^*$ value decreases, which is well consistent with the result on the synthetic glaze. As the amount of titanium increases in the glaze, the $a^*$ and $b^*$ values decrease; on the other hand, the $L^*$ value increases, which is well consistent with the result on the synthetic glaze.

• 한국광학회지
• /
• 제18권5호
• /
• pp.362-366
• /
• 2007

본 연구에서는 3 메가픽셀, 2.5배 줌 카메라폰 모듈용 비구면 유리렌즈 개발을 목적으로 실험계획법(DOE)을 적용하여 성형용 초경 코어의 연삭가공조건을 구하고, 이를 활용하여 비구면 Glass렌즈 성형용 초경합금(WC) 코어를 초정밀 연삭가공을 수행하였다. 또한 가공된 성형용 코어의 가공면 위에 이온증착법으로 다이아몬드상 탄소(Diamond-Like Carbon; DLC) 코팅을 수행하여 DLC 코팅이 성형용 코어의 형상정도(PV)와 표면조도(Ra)에 미치는 영향을 평가하였으며, 비구면 Glass렌즈를 동일한 조건에서 성형하여 성형렌즈의 광학적 특성을 비교하여 성형용 코어면의 DLC 코팅 효과에 대하여 검토하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.395-395
• /
• 2000

Optimization of existing processes becomes more important than the past as environmental problems and concerns about energy savings stand out. When we can model a process mathematically, we can easily optimize it by using the model as constraints. However, modeling is very difficult for most chemical processes as they include numerous units together with their correlation and we can hardly obtain parameters. Therefore, optimization that is based on the process models is, in turn, hard to perform. Especially, f3r unknown processes, such as bioprocess or microelectronics materials process, optimization using mathematical model (first principle model) is nearly impossible, as we cannot understand the inside mechanism. Consequently, we propose a few optimization method using empirical model evolutionarily instead of mathematical model. In this method, firstly, designing experiments is executed fur removing unecessary experiments. D-optimal DOE is the most developed one among DOEs. It calculates design points so as to minimize the parameters variances of empirical model. Experiments must be performed in order to see the causation between input variables and output variables as only correlation structure can be detected in historical data. And then, using data generated by experiments, empirical model, i.e. response surface is built by PLS or MLR. Now, as process model is constructed, it is used as objective function for optimization. As the optimum point is a local one. above procedures are repeated while moving to a new experiment region fur finding the global optimum point. As a result of application to the pulp digester benchmark model, kappa number that is an indication fur impurity contents decreased to very low value, 3.0394 from 29.7091. From the result, we can see that the proposed methodology has sufficient good performance fur optimization, and is also applicable to real processes.

• 대한기계학회논문집A
• /
• 제35권9호
• /
• pp.1007-1013
• /
• 2011

상용차용 다층관 벨로우즈는 우수한 유연성과 내구성이 요구되므로 단층으로 제조되는 승용차용 벨로우즈와는 다르게 다층의 형태로 제작된다. 단층 벨로우즈의 유한요소해석과 최적화에 대한 연구는 활발히 진행되고 있으나, 층과 층사이에 갭이 존재하는 다층형 벨로우즈의 유한요소해석과 최적화 연구는 미진하다. 따라서 본 연구에서는 해석의 신뢰성 향상을 위해 다층형 벨로우즈에 적합한 유한요소 모델을 제시하였으며, 다층관 벨로우즈의 형상 최적화를 위해 실험계획법과 D-Optimal 방법에 기반을 둔 순차적 실험계획에 의한 크리깅 메타모델을 적용하였다.

• Advances in materials Research
• /
• 제6권1호
• /
• pp.79-91
• /
• 2017

In the present work, a design of experiment (DOE) technique using Taguchi method, has been applied to optimize the properties of ODS tungsten heavy alloys(WHAs). In this work Taguchi method involves nine experiments groups for four processing parameters (compaction pressure, sintering temperature, binding material type, and oxide type) with three levels was implemented. The signal-to-noise (S/N) ratio and analysis of variance (ANOVA) were employed to obtain the optimal process parameter levels and to analyze the effect of these parameters on density, electrical conductivity, hardness and compressive strength values. The results showed that all the chosen factors have significant effects on all properties of ODS tungsten heavy alloys samples. The density, electrical conductivity and hardness increases with the increase in sintering temperature. The analysis of the verification experiments for the physical properties (density and Electrical conductivity) has shown that Taguchi parameter design can successfully verify the optimal parameters, where the difference between the predicted and the verified values of relative density and electrical conductivity is about 1.01% and 1.15% respectively.