• Journal of Power Electronics
• /
• 제9권6호
• /
• pp.960-968
• /
• 2009

This paper presents a design optimization process for interior permanent magnet synchronous motors (IPMSM) for hybrid electric compressors (HEC) which are applied to hybrid electrical vehicles. A hybrid electric compressor is composed of an electric motor driving section and an engine driving section which is connected to the engine by a pulley belt. A hybrid electric compressor driving motor requires half of the full driving power of a compressor. Even though an engine is not operated at the idling stop mode, the electric motor drives the air-conditioner compressor by itself so that the air conditioning system can produce its minimum cooling capacity. In this paper, the design optimization of an IPMSM for a 42 (V) applied voltage system is studied using the design of experiment (DOE) and response surface method (RSM) of 6sigma. The driving characteristics of this motor drive system are measured and analyzed by experiment.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.34-36
• /
• 2005

Copper wire bonding is an alternative interconnection technology that serves as a viable and cost saving alternative to gold wire bonding. In this paper, ultrasonic wedge bonding with $25{\mu}m$ copper wire on Au/Ni/Cu metallization of a PCB substrate was performed at ambient temperature. The central composite design of experiment (DOE) approach was applied to optimize the copper wire wedge bonding process parameters. After that, pull test of the wedge bond was performed to study the bond strength and to find the optimum bonding parameters. SEM was used to observe the cross section of the wedge bond. The pull test results show good performance of the wedge bond. Additionally, DOE results gave the optimized parameter for both the first bond and the second bond. Cross section analysis shows a continuous interconnection between the copper wire and Au/Ni/Cu metallization. The diffusion of Cu into the Au layer was also observed.

• Transactions on Electrical and Electronic Materials
• /
• 제6권3호
• /
• pp.87-90
• /
• 2005

$SiO_2$ via-hole etching with a high aspect ratio is a key process in fabricating ULSI devices; however, accumulated charge during plasma etching can cause etching stop, micro-loading effects, and charge build-up damage. To alleviate this concern, charge-up damage sensor was fabricated for the ultimate goal of real-time monitoring of accumulated charge. As an effort to reach the ultimate goal, fabricated sensor was used for electrical potential measurements of via holes between two poly-Si electrodes and roughly characterized under various plasma conditions using statistical design of experiment (DOE). The successful identification of potential difference under various plasma conditions not only supports the evidence of potential charge-up damage, but also leads the direction of future study.

• 한국추진공학회지
• /
• 제2권2호
• /
• pp.99-107
• /
• 1998

ASE120 엔진 연소기에 쓰이는 벤츄리(venturi)형 예혼합기의 혼합성능을 시험 평가하였다. 이 시험에서는 가스연료 대신 찬공기를 주입하고 혼합공기의 온도를 측정함으로 혼합정도를 계산하였다. DOE 기법을 사용하여 시험변수 matrix를 구성하고 시험결과를 분석하여 최적의 변수조합을 가지는 형상을 도출하였다. 선정된 형상에 대하여 확인시험이 수행되었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.348-348
• /
• 2005

High capacitance MLCC has been enabled through the use of nickel electrodes to produce thinner layers at acceptable costs. High capacitance MLCC devices offer significant advantages to electrolytics such as tantalum and aluminum ; Lower ESR for high frequency applications. Non-polarized. Many process improvement have enabled this technology Higher dielectric constants Thinner dielectric and electrode layers through BME More accurate layer construction. This study is high capacitance MLCC electrical propertics. reliability, Analysis on DOE(Design Of Experiment) of the electical propertics.

• 한국전기전자재료학회논문지
• /
• 제20권8호
• /
• pp.720-725
• /
• 2007

This study investigated the pressing conditions in the molding of aspheric glass lenses for the mega pixel phone camera module using the DOE method. Tungsten carbide (WC; Japan, Everloy Co., 002K),which contained 0.5 w% cobalt (Co), was used to build the mold. The mold surface was ultra-precision ground and polished, and its form accuracy (PV) was 0.85um in aspheric surface. We selected four factors, pressing temperature, force and time of first step, and force of second step, respectively, as the parameters of the pressing process. in order to reduce the number of experiments, we applied fractional factorial design considering the main effects and two-way interactions. The analysis results indicate that the only two main effects, the pressing temperature and the time of pressing step 1, are available for the form accuracy (PV) of the molded lens. The analysis results indicated that the best combination of the factors for lowering the form accuracy(PV) value of molded lens was to have them at their low levels.

• International Journal of Fluid Machinery and Systems
• /
• 제9권2호
• /
• pp.150-158
• /
• 2016

In this paper, a new framework that works the automatic execution with less design cycle time and human intervention bottlenecks is introduced to optimize the vortex shedder design by numerical integration method. This framework is based on iSIGHT combined with the pre-processor GAMBIT, and flow analysis software FLUENT. Two vortex shedders, circular with slit and triangular- semi circular cylinder, are employed as the designed models to be optimized, and DOE driver is used for optimization. According to the essential properties of a vortex shedder, it has found that the best diameters are 30mm for circular cylinder with slit and 30 to 35 mm for tri-semi cylinder. For slit ratio, 0.1 and 0.15 are the optimized values for circular with slit and tri-semi cylinder respectively. And it is found that these optimal results generated by DOE automated design cycle are in well agreement with the experiment.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제6권2호
• /
• pp.187-205
• /
• 2014

The global price of oil, which is both finite and limited in quantity, has been rising steadily because of the increasing requirements for energy in both developing and developed countries. Furthermore, regulations have been strengthened across all industries to address global warming. Many studies of hull resistance, propulsion and operation of ships have been performed to reduce fuel consumption and emissions. This study examined the design parameters of the propeller boss cap fin (PBCF) and hub cap for 6,000TEU container ships to improve the propulsion efficiency. The design parameters of PBCF have been selected based on the geometrical shape. Computational fluid dynamics (CFD) analysis with a propeller open water (POW) test was performed to check the validity of CFD analysis. The design of experiment (DOE) case was selected as a full factorial design, and the experiment was analyzed by POW and CFD analysis. Analysis of variance (ANOVA) was performed to determine the correlation among design parameters. Four design alternatives of PBCF were selected from the DOE. The shape of a propeller hub cap was selected as a divergent shape, and the divergent angle was determined by the DOE. Four design alternatives of PBCF were attached to the divergent hub cap, and the POW was estimated by CFD. As a result, the divergent hub cap with PBCF has a negative effect on the POW, which is induced by an increase in torque coefficient. A POW test and cavitation test were performed with a divergent hub cap with PBCF to verify the CFD result. The POW test result showed that the open water efficiency was increased approximately 2% with a divergent hub cap compared to a normal cap. The POW test result was similar to the CFD result, and the divergent hub cap with the PBCF models showed lower open water efficiency. This was attributed to an increase in the torque coefficient just like the CFD results. A cavitation test was performed using the 2 models selected. The test result showed that the hub vortex is increased downstream of the propeller.

• 한국기계가공학회지
• /
• 제20권1호
• /
• pp.103-109
• /
• 2021

Fine chips generated by machining have an impact on machine failure and quality of machined products, it is necessary to remove the chips, so the microchip collection and removal device by rotating conveyor belt with neodymium permanent magnets was developed. In this research, to solve the problem for reducing the existing microchips in the tank, a micro-chip removal device by rotating conveyor belt with neodymium permanent magnets developed. In the development of micro-chip removal device, 3D CATIA modeling was used, and the flow analysis and the electromagnetic force analysis were performed with COMSOL Multiphysics program. To evaluate the performance of the prototypes produced, design of experiments (DOE) is used to obtain the effect of neodymium conveyor movement speed on chip removal for the ANOVA analysis of recovered powders. An experiment was conducted to investigate the effect of the conveyor feed rate on the chip removal performance in detail. As a result of the experiment, it was confirmed that the slower the feeding speed of the fine chip removing device, the more efficient the chip removal.

• 한국응용과학기술학회지
• /
• 제39권5호
• /
• pp.623-631
• /
• 2022

실험 계획법을 활용하여 세라마이드가 고함량으로 함유된 수화 액정형 베시클의 입자 사이즈에 영향을 미치는 인자를 분석하고 혼합물 조성의 최적화를 시도하였다. 베시클 입자 사이즈에 영향을 주는 주요 변수로 제조 온도, 에탄올 양, 초음파 시간을 각각 정하고, 다구찌 방법의 S/N비 산출과 ANOVA 분석을 통해, 이들 변수들이 입자 사이즈에 미치는 영향을 살펴보았다. 또한 혼합물 실험 계획법의 심플렉스 중심 설계에 따라, 베시클 막을 구성하는 세 지질 성분, 인지질(HPC), 콜레스테롤(Chol), 세라마이드(Cer)의 혼합 조성 실험을 수행하였다. 실험에서 얻어진 데이터로부터 회귀분석을 실시하여 모델식을 구하고, 베시클 입자 사이즈를 최소로 만들기 위한 세 지질 성분의 최적 혼합 조성은 HPC(0.6), Chol(0.1), Cer(0.3)으로 구해졌다.