• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표논문집(II)
• /
• pp.262-268
• /
• 1998

This research is to examine the selected method of optimal mixing proportion and cost analysis in the super flowing concrete. As confined water $ratio($\beta_p$)$ and K is introduced, itis to establish optimal mixing design of super flowing concrete according to the steps of paste, mortar and concrete. From paste and mortar test, it was led to $$\beta_p$$ and $K_p$satisfying the optimum condions depending on the kinds of binders. Then $$\beta_p$$ and $K_p$ is reflected to the mix condition of super flowing concrete. The result of test, the mix condition of super flowing concrete satisfied the quality performance of concrete with adjustment of additional rate of the superplasticizer. Besides, in case of design strength $350kg/\textrm{cm}^2$ of concrete, material cost in super flowing concrete is able to be reduced 5~16% in replacement of fly ash 30% in ordinary portland cement and slag cement.

• 전자공학회논문지C
• /
• 제34C권7호
• /
• pp.38-50
• /
• 1997

This paper concerns a VHDL design and simulation of an accurate and cost-effective fuzzy logic controller (FLC). The accurcy of the proposed FLC is obtained by using the center of gravity (COG) defuzzifier that considers both membership values and spans of membership functions in calculating a crisp value. The cost-effectiveness of the proposed FLC is obtained by restructuring the conventional FLC in the following ways: Firstly, the MAX-MIN inference is inference is replaced by a read-modify-write operation that can be implemented economically in the structure of register files. Secondly, the division in the COG defuzzifier is avoided by finding the moment equilibrium point. The proposed COG defuzzifier has two disadvantages that it requires additional multipliers and it takes a lot of computation time to find the moment equilibrium point. The first disadvantage is overcome by replacing the mulitpliers with stochastic AND operations and the second disadvantage is alleviated by using a coarse-to-fine searching algorithm. The proposed FLC is described in VHDL structurally and behaviorally and whether it is working well or not is checked on SYNOPSYS VHDL simulator by using the truck backer-upper control problem.

• 대한토목학회논문집
• /
• 제42권6호
• /
• pp.837-842
• /
• 2022

2013년에 개발된 지능형 철도선형계획 프로그램(ei-Rail)은 주로 해외의 신규 철도건설사업 사전 기획 분석 및 설계 결과 검증 등에 활용되어왔다. 그러나 한국 철도산업의 해외 진출 대상국인 개발도상국에서는 대규모 비용이 소요되는 신규 철도건설사업 보다는 기존 철도의 선형개량을 통한 증속, 또는 단선철도의 복선화 등의 사업이 보다 필요하고 실행가능성이 높은 것으로 판단되며, 이런 유형의 사업수요가 지속적으로 발생하고 있다. 이에 본 연구에서는 기존의 신규 철도건설 사업 분석기능 중심의 ei-Rail 프로그램에 철도복선화 사업 분석기능을 추가하고자, 철도 복선화사업 모듈을 개발하였다. 기존에 운행 중인 철도 선형자료를 기반으로 복선화 사업의 종류와 규모를 반영하고 대상 지역별 공종 단가를 적용하여 공사비를 산출하고 설계도면 제작을 자동화할 수 있도록 하였다. 그리고 해외의 사례 적용을 통하여 ei-Rail의 복선화 사업 분석기능을 검증하였다. 향후 해외를 대상으로 하는 철도 복선화 사업의 기획 및 분석결과 검증을 보다 효율적으로 수행할 수 있을 것으로 기대한다.

• 한국관개배수논문집
• /
• 제17권2호
• /
• pp.28-34
• /
• 2010

This study re-exams hydrologic stability on spillway outlet capacity of agricultural reservoirs using hydrologic data with current rainfall condition instead of project hydrologic data applied at design on Backgok reservoir located in Chungbuk province. It is concluded that Backgok reservoir is not hydrologically stable and therefore structural measures including the extension of spillway and non structural measures should be taken. Continuous basic plan for river maintenance including additional bank reinforcement to bottom river shall be carried out. Due to high peak flood with more than 290% compared to 200 year frequency probability flood which was design standard of the past in view of the results of calculating PMF according to revised design standard for reservoirs, there could a problem for securing rationality in case of applying PMF with design flood. Therefore, hydrological stability, construction, and maintenance cost shall be synthetically studied and reasonal application shall be made if the decision is made on applying PMF with design flood.

• Asian Pacific Journal of Cancer Prevention
• /
• 제16권16호
• /
• pp.6857-6862
• /
• 2015

Background: To identify the optimal cost effective strategy for the management of women having ASC-US who attended at King Chulalongkorn Memorial Hospital (KMCH). Design: An Economical Analysis based on a retrospective study. Subject: The women who were referred to the gynecological department due to screening result of ASC-US at King Chulalongkorn Memorial Hospital, a general and tertiary referral center in Bangkok Thailand, from Jan 2008 - Dec 2012. Materials and Methods: A decision tree-based was constructed to evaluate the cost effectiveness of three follow up strategies in the management of ASC-US results: repeat cytology, triage with HPV testing and immediate colposcopy. Each ASC-US woman made the decision of each strategy after receiving all details about this algorithm, advantages and disadvantages of each strategy from a doctor. The model compared the incremental costs per case of high-grade cervical intraepithelial neoplasia (CIN2+) detected as measured by incremental cost-effectiveness ratio (ICER). Results: From the provider's perspective, immediate colposcopy is the least costly strategy and also the most effective option among the three follow up strategies. Compared with HPV triage, repeat cytology triage is less costly than HPV triage, whereas the latter provides a more effective option at an incremental cost-effectiveness ratio (ICER) of 56,048 Baht per additional case of CIN 2+ detected. From the patient's perspective, the least costly and least effective is repeat cytology triage. Repeat colposcopy has an incremental cost-effectiveness (ICER) of 2,500 Baht per additional case of CIN2+ detected when compared to colposcopy. From the sensitivity analysis, immediate colposcopy triage is no longer cost effective when the cost exceeds 2,250 Baht or the cost of cytology is less than 50 Baht (1USD = 31.58 THB). Conclusions: In women with ASC-US cytology, colposcopy is more cost-effective than repeat cytology or triage with HPV testing for both provider and patient perspectives.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2000년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall 2000
• /
• pp.381-388
• /
• 2000

The steel piers and the concrete-filled steel piers, in spite of reasonable strength, high ductility, small section, and fast construction, have not been considered as the alternatives to the RC piers even in the highly populated urban area where aseismic safety, limited space and fast construction are indispensably required. In this paper, a steel pier and 4 box type concrete-filled steel piers were tested with the quasi-static cyclic loading to estimate the ductility and the strength. Additional devices such as base rib, turn-buckle, and anchor bolted added at the to increase the ductility with minimum additional cost. The result showed that the concrete filled-in steel piers had higher energy absorbtion and strength than steel piers had, but also showed that slight overlooking in the design and fabrication could lead to the abrupt fracture just after small local buckling at the bottom.

• 대한인간공학회:학술대회논문집
• /
• 대한인간공학회 1995년도 추계학술대회논문집
• /
• pp.214-218
• /
• 1995

A lot of design guidelines have been proposed for menu-drive interfaces, but they are applicable only to the menus on ordinary CRT displays. Many hardware products, however, cannot employ large displays because of the cost and space limitations. Instead, a single-line display menu (SDM) is widely used, and the designers need useful guidelines applicable to the SDM. A focus is often placed upon the optimal menu structure, but only the standard menu structures, such as $64^{\1}, 8^{\2}, 4^{\3}, and 2^{\6}$, are tested for optimality. In many cases, however, ill defined or asymmetric structures are suggested as design alternatives. To determine the optimal menu structure, user performance should be obtained in terms of quantitative measures for each of the optional structures considered. Hence, a model is needed to provide a predicted value of user performance for a given menu structure. Although severaal models have been proposed for ordinary menus, none is available for the SDM yet. A performance model was developed in this study using the neural network approach. A The model developed in this study is capable of providing quantiative measures of human performance for any menu structures without conducting additional experiments, which will save much time and reduce the design cost.

• Computers and Concrete
• /
• 제12권6호
• /
• pp.755-774
• /
• 2013

Considering the well known environmental issues of cement manufacturing (direct and indirect levels of $CO_2$ emissions), clinker replacement by supplementary cementing materials (SCM) can be a very promising first step in reducing considerably the associated emissions. However, such a reduction is possible up to a particular level of SCM utilization, influenced by the rate of its pozzolanic reaction. In this study a (4-step) structured methodology is proposed in order to be able to further adjust the concrete mix design of a particular SCM, in achieving additional reduction of the associated levels of $CO_2$ emissions and being at the same time accepted from a derived concrete strength and service life point of view. On this note, the aim of this study is twofold. To evaluate the environmental contribution of each concrete component and to provide the best possible mix design configuration, balanced between the principles of sustainability (low environmental cost) and durability (accepted concrete strength and service life ). It is shown that such a balance can be achieved, by utilising SCM by-products in the concrete mix, reducing in this way the fixed environmental emissions without compromising the long-term safety and durability of the structure.

• 소성∙가공
• /
• 제13권4호
• /
• pp.359-364
• /
• 2004

In the multi-stage former, a manufacture of hexagonal fitting nut was generated in a defective products about 70∼80% in the industry field. Products generated in defects manufactured to be a machining about 60%. Additional process increased a product cost and decreased a product rate. Therefore, it is important to predict and design a preform reducing defective products in the early stage of process design. So in the study Defects for manufacturing hexagonal fitting nut verified a cause through the finite element simulation. To reduce a defective generation. a preform designed and a designed preform verified through the finite element simulation. In conclusion, a generated defects when a hexagonal fitting nut manufactured should reduce if a round dimension of preform reduced and a part of opposition angle distributed in plenty a volume.

• 전기학회논문지
• /
• 제58권1호
• /
• pp.57-62
• /
• 2009

This paper deals with the optimal design of a shield plate in order to minimize Extremely-Low-Frequency(ELF) magnetic fields generated from three-phase bus bars. Combining an evolutionary strategy with a 3D finite element analysis tool, the main dimensions of the shield plate are sought out. The optimization procedure consists of two separated design stages to take into account all foreseen structures of the plate. In the first stage, the basic dimensions of the plate are optimized including the distance between the plate and the bus bars. Then the usefulness of the additional structures such as a slit and fillet is investigated in the second stage. Finally the optimum design of the shield plate is suggested from the viewpoint of the shielding effectiveness and manufacturing cost.