• Journal of the Korea Concrete Institute
• /
• v.15 no.5
• /
• pp.705-714
• /
• 2003

Even though Korean peninsula is located in regions of moderate seismic risks, current seismic design provisions of the roadway bridge design code have adopted the AASHTO code which is based on the requirements for high seismic regions. The objective of this research is to investigate the seismic performance of circular reinforced concrete (RC) bridge piers with limited ductility, which may be desirable in low or moderate seismic regions, such as in Korea. Four test specimens were designed and constructed. The reference specimen was designed with longitudinal steel ratio as 1.01% and the confinement reinforcement ratio as 0.13% without considering earthquake, and three other test specimens were designed in accordance with a limited-ductility concept as 0.3% for the confinement steel ratio. This confinement ratio is 0.32 times of minimum lateral reinforcement specified in current seismic design provisions, and 2.3 times of lateral reinforcement required in nonseismic design provisions. The pseudo-dynamic test was carried out to evaluate the seismic performance of full-scale specimens in size of 1.2m diameter and 4.8m height. Judging from the experiment, the reference specimen was not satisfactory for the demand displacement ductility ${\mu}$=5.0, but three limited-ductility specimens appeared to have the displacement ductility of more than 5.

• Journal of Aerospace System Engineering
• /
• v.18 no.1
• /
• pp.64-71
• /
• 2024

The external fuel tank of an aircraft is a main component that can increase the cruising range of the aircraft. It must be able to be stably separated from the pylon in an emergency situation. At this time, a separation load is applied to the fin and the pivot of the external fuel tank. To stably separate the external fuel tank, the structural soundness of the fin and the pivot must be confirmed. In this study, structural tests were conducted to verify the structural integrity of the external fuel tank pin and pivot when the external fuel tank was separated from the aircraft. Results are then presented. In this paper, a test configuration diagram consisting of the hydraulic and load control equipment, data acquisition system, and pneumatic supply unit used in the structural test was explained. Test installation and test load application plan for each test condition were provided. As results of the structural test, it was found that test load and internal pressure of the test specimen were properly controlled within the allowable range in each test. It was confirmed that serious structural defects in the test specimen did not occur under required load conditions. In conclusion, through structural test for design limit load and design ultimate load, it was proven that the fin and pivot of the external fuel tank for aircraft covered in this study had sufficient structural strength.

• Asian Pacific Journal of Cancer Prevention
• /
• v.15 no.16
• /
• pp.6603-6608
• /
• 2014

Cervical cancer is one of the leading causes of cancer in women worldwide. One way by which the incidence of this malignant disease can be minimized is by imparting knowledge through health education. This study aimed at developing an educational package on cervical cancer (EPCC) and determining its effectiveness in terms of significant increase in knowledge of rural women regarding cervical cancer. A one group pre-test, post-test design was adopted. Thirty rural women were selected using a convenient sampling method. Data were collected using a demographic questionnaire and a structured knowledge questionnaire developed by the researchers. The EPCC was designed for a duration of one hour and 10 minutes. The structured knowledge questionnaire was first administered as the pre-test, following which knowledge on cervical cancer was imparted using the EPCC. On the 8th day, the post-test was administered. Data were analyzed using descriptive and inferential statistics. The mean post-test knowledge score of the women regarding cervical cancer was significantly higher than that of their mean pre-test score, indicating that the EPCC was effective in improving the knowledge of rural women on cervical cancer. The association between pre-test knowledge scores and selected demo-graphic variables were computed using chi-square test showed that pre-test knowledge score of the women regarding cervical cancer was independent of all the socio-demographic variables. It was concluded that the EPCC is effective in improving the knowledge of women, regarding cervical cancer. Since the prevalence of cervical cancer is high, there is an immediate need to educate women on prevention of cervical cancer.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.45 no.3
• /
• pp.280-289
• /
• 2018

This study aimed to investigate the effects of learning with role-playing on student satisfaction and achievement regarding behavior management teaching in pediatric dentistry. 93 students were divided into 19 groups and randomly assigned to role-play as a doctor, patient, parent, assistant, or narrator. Their performances were evaluated by the instructor and the satisfaction survey was conducted. All participants took the written test and were asked to compare lecture and role-playing with regard to the effectiveness of learning. Statistical analysis was performed with Mann-Whitney U test, Independent T-test, and Kruskal-Wallis test. 68 students (73.1%) who believed that the role-playing was more helpful than lecture showed higher level of satisfaction than students who believed lecture was more helpful. But there were no differences in the tutor evaluation score and the written test scores. Participants in the patient management scenario showed higher level of descriptive question scores of the written test and tutor evaluation score than those who participate in the parent management scenario. There were no differences between the role groups. Role-playing may help students to become more interested and participatory in learning behavior management. The level of satisfaction may differ by the design and content of the scenario.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.34 no.3
• /
• pp.157-166
• /
• 2018

Purpose: This study was aimed to compare the consistency between the custom abutment design and the output in two CAD software programs. Materials and Methods: Customized abutments were designed by using 3Shape Dental System CAD software and Delta9 CAD software on a plaster model with implants (CRM STL file). After milling of the designed abutments, the abutments were scanned with a contact method scanner (Test STL file). We overlaid the Test STL file with each CRM STL file by using inspection software, and then compared the milling reproducibility by measuring the output error of the specimens from each CAD software program. Results: The Delta9 showed better milling reproducibility than 3Shape when comparing the milling errors obtained with a full scan of all specimens (P < .05) and also when comparing the axial wall region specifically according to the axial angle. With 0.9 mm marginal radius, the Delta9 showed better consistency between the design and the output than 3Shape (P < .05). While, anti-rotation form had no significant difference in error between the two systems. When cumulative errors were compared, the Delta9 showed better milling reproducibility in almost cases (P < .05). Conclusion: Delta9 showed a significantly smaller error for most of the abutment design options. This means that it is possible to facilitate generation of printouts with reliable reproducibility and high precision with respect to the planned design.

• KIEAE Journal
• /
• v.14 no.2
• /
• pp.77-86
• /
• 2014

Plenty of efforts have been made in the traditional architecture of Korea, Hanok, to develop various elements such as restoration, the introduction of new design, and energy-saving while systemic setups on standard and evaluation of eco-friendly energy design of Hanok are lacking. If we evaluate energy performance based on current standards without reflecting unique features of Hanok on the system, Hanok will be included in the very low grade among the residential buildings being included in the approval system of eco-friendly architecture or the unique features will be modified and the burden of increased construction cost. Therefore, this study is to prepare the basic reference for the introductory evaluation system by evaluating the energy performance level of NEO-Hanok based on the current building energy rating system. The result for NEO-Hanok based on the building energy rating system, we propose the rating standard with scorecard elements of NEO-Hanok by considering the necessity of identity and standard for NEO-Hanok. As a result of infiltration test to check the tightness, it was measured as 10.81 times/h (50 ACH). As we switch from the main insulation for the wall from the glass wool 64k(0.035W/mk) to rigid polyurethane foam first class first unit (0.024W/mk), the result was slightly increased from the first demand quantity rating yield $249.8kWh/m^2{\cdot}yr$ to $235.0kWh/m^2{\cdot}yr$. Current certificate system is focused more on the heating load than the cooling load, it is disadvantageous for Hanok, which has less cooling energy consumption in summer. The rating result from the target building study is level 4.

• The Journal of Advanced Prosthodontics
• /
• v.10 no.5
• /
• pp.335-339
• /
• 2018

PURPOSE. The purpose of the present study was to compare scanning trueness and precision between an abutment impression and a stone model according to dental computer-aided design/computer-aided manufacturing (CAD/CAM) evaluation standards. MATERIALS AND METHODS. To evaluate trueness, the abutment impression and stone model were scanned to obtain the first 3-dimensional (3-D) stereolithography (STL) file. Next, the abutment impression or stone model was removed from the scanner and re-fixed on the table; scanning was then repeated so that 11 files were obtained for each scan type. To evaluate precision, the abutment impression or stone model was scanned to obtain the first 3-D STL file. Without moving it, scanning was performed 10 more times, so that 11 files were obtained for each scan type. By superimposing the first scanned STL file onto the other STL files one by one, 10 color-difference maps and reports were obtained; i.e., 10 experimental scans per type. The independent t-test was used to compare root mean square (RMS) data between the groups (${\alpha}=.05$). RESULTS. The $RMS{\pm}SD$ values of scanning trueness of the abutment impression and stone model were $22.4{\pm}4.4$ and $17.4{\pm}3.5{\mu}m$, respectively (P<.012). The $RMS{\pm}SD$ values of scanning precision of the abutment impression and stone model were $16.4{\pm}2.9$ and $14.6{\pm}1.6{\mu}m$, respectively (P=.108). CONCLUSION. There was a significant difference in scanning trueness between the abutment impression and stone model, as evaluated according to dental CAD/CAM standards. However, all scans showed high trueness and precision.

• Korean Journal of Human Ecology
• /
• v.14 no.6
• /
• pp.995-1006
• /
• 2005

The purpose of this study was to investigate the wearing sensation and satisfaction of high school girls' winter uniform jackets according to the fabrics and the shapes. The fabrics were divided into four parts of stretch and non-stretch woven fabrics. The shapes were divided into two parts of tight and general types. The results were as followings: 1. In the aspect of the appearance evaluation for the uniform jackets, silhouette and length item showed significant differences in fabric and shape. The non-stretch woven fabric and tight type was more satisfying than the stretch fabric and general type because its silhouette and length were shorter and fitter than the stretch one and general type. The jackets of non-stretch woven fabric of tight type were evaluated as the thinnest in the silhouette and were evaluated as the shortest in the length. Conversely, the jackets of stretch woven fabric of general type were evaluated as the thickest and longest. 2. As for the wearing sensation of school uniform jacket, all test items showed significant differences in fabric and shape. The stretch fabric and general type was more satisfying than the non-stretch woven fabric and tight type because the jacket of stretch fabric and general type was felt more comfortable in activities, and wearing. Accordingly, the appearance evaluation for uniforms' jacket is in sharp contrast with that of wearing sensation.

• Korean Journal of Human Ecology
• /
• v.24 no.6
• /
• pp.847-857
• /
• 2015

The ratio of small-breasted women occupies over 20% among Korean women in their twenties. However, the commercial brassieres for the small-breasted women were not fitted well to their breast shapes. In this research, the various commercial mold brasseries for small-breasted women were evaluated through the wearing test and the analysis of 3D images which were scanned from their torsos wearing the brassieres. In addition, professional panels performed the appearance evaluation based on the 2D front and side images captured from 3D images taken by 3D measurement systems. As the results, we found that small-breasted women preferred a 3/4 cup brassiere, of which volume is concentrated in the lower cup. The most preferred brassiere in wearing state shows that the characteristic angle between the chest and the upper cup is about 167 degrees, which is smaller than those of another brassieres, and that the ratio of the radius of curvature of the nipple part to that of the lower cup was about 0.78. These results provide important implications regarding the design of mold brassieres for small-breasted women in spite of the fact that these results represent the selected set of commercial brassieres. Therefore, further studies are highly demanded for the most suitable design information of mold cup for small-breasted women.

• Journal of Biomedical Engineering Research
• /
• v.21 no.3 s.61
• /
• pp.303-309
• /
• 2000

An accurate quantitative biomechanical evaluation for the spasticity caused by the disorder of central nervous system was made in this study. A sudden leg dropper was designed to generate objective testing environment at every trial. 3-dimensional motion analysis system(Elite. B.T.S. Italy) was used to measure kinematic data which were angle. and angular velocity of a lower limb. A program was developed to analyze the kinematic data of lower limb motion. and dynamic EMG data at the same time. To evaluate spasticity quantitatively. total 26 parameters including 14 parameters newly driven were analyzed, and statistical analysis were made for bilateral correlations. Results showed possibility to make accurate quantitative and objective evaluation for spasticity with various new parameters using new devices and program.