• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.7
• /
• pp.121-126
• /
• 1996

In this paper an MMIC VCO which can be used in a double conversion TV tuner is designed, fabricated and measured. The VCO is designed using the small signal method and fabricated using ETRI GaAs MMIC foundry. The 3x200$\mu$m gate width MESFET with 1$\mu$m gate length is used for an active device and MIM capacitors, spiral inductors, thin film resitors are used as passive elements. The VCO has output power of 10.95dBm at 1955 MHz with 5V bias voltage and 4V tuning voltage. The oscillation frequency change form 1947 MHz to 1964 MHz is obtaine dby an external varactor diode connected to the gate with a tuning voltage from 0 V to 6V.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.1
• /
• pp.42-46
• /
• 2003

In this paper, an MMIC broadband amplifier for wireless communication systems has been developed by using an active feedback method. This active feedback operates at much higher frequencies than a method by a spiral inductor feedback and its size is independent of the inductance value. The MMIC broadband amplifier was designed using a $0.5{\;}{\mutextrm{m}}$ MESFET library. The fabricated chip area was $1.4{\;}mm{\;}{\times}{\;}1.4{\;}mm. Measurement showed a gain of 18 dB with a gain flatness of ${\pm}3$ dB in a 1.5 GHz~3.5 GHz band. The maximum output power and the minimum noise figure were 14 dBm and 2.5 dB in the same band, respectively.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.1
• /
• pp.56-61
• /
• 1986

Rotor dynamic response of pumps is greatly influenced by the nature of the hydraulic forces arising from wearing seal, balance drum and impeller, etc.. Therefore, rotor dynamic analysis should be conducted during the design stage in order to aleviate some of the vibrational problems which might occur during the operational life of pumps. Previsousely, the authors have proposed the method to obtain the dynamic seal coefficients of the annular plain seal, convergent and divergent tapered seals, parallel grooved seal, spiral grooved seal and annular stepped seal. On the basis of these results, this paper presents the investigated effect of seals on the stability behavior of a centrifugal pump. The results show the effects of seal geometry, pressure difference, clearance, length/diameter ratio, on stability behavior.

• Interaction and multiscale mechanics
• /
• v.2 no.4
• /
• pp.413-430
• /
• 2009

The stator tooth is a key component of the electromechanical integrated toroidal drive system. The stator tooth is spiral in shape and the calculation of its displacements is difficult. In this paper, using the coordinate transformation method, the displacements of the stator tooth in the local coordinate system are expressed as the function of the variable in the drive coordinate system. Using the minimum potential energy principle, the equations of the displacements of the stator tooth under the loads are deduced. The displacement distributions within the stator tooth are investigated and the changes of the displacement distributions along with the main parameters are analyzed. This research can offer the basis for the strength and stiffness design of the drive system.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2001.09a
• /
• pp.423-430
• /
• 2001

This research was conducted to investigate the seismic behavior and ductility of circular spiral reinforcement concrete bridge columns used in high strength concrete. The experimental variables consisted of transverse steel amount and spacing, different axial load levels. From the test results, sufficient displacement ductility(at least 5.5) was observed for the columus which was satisfied wi th the requirement confinement steel amount of the Korean Bridge Design Specification. In case of the columns with 50 MPa of concrete compressive strength, the columns wi th 80 % of the confinement steel amount requirement showed adequate displacement ductility(at least 6.5) under 0.2 of axial load level. And in case of the columns with 60.2 77a of concrete compressive strength, the columns with 44 \ulcorner of the confinement steel requirement provided adequate displacement ductilit under less than 0.1 of axial load level and the columns with 0.22 % provided showed comparatively high the ducti1iffy under 0.21 of axial load level.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.943-948
• /
• 2003

The experimental study for oblong section was carried out by the column test in weak axis. The column specimens had 3 types of transverse steel configurations, such as interlocking spirals, interlocking circular hoop ties and rectangular ties. The oblong columns with interlocking spirals and with interlocking circular hoop ties showed better seismic performance than the rectangular columns with rectangular hoops and cross-ties. The objectives of this study were to provide experimental data on the behavior of interlocking spiral columns under cyclic loading, to compare the performance of columns with interlocking spirals to columns with various transverse steel configurations, to study the flexural detailing of interlocking spirals, interlocking circular hoops, and other transverse steel configurations as the transverse reinforcement, and to make recommendations for the design of bridge columns incorporating interlocking spirals, circular hoops as the transverse reinforcement.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.333-337
• /
• 2003

In this paper, 5.2 GHz WLAN BPF(Band Pass Filter) using LTCC(Low temperature co-firing ceramic) Multilayer technology was simulated and manufactured. A DGS(Defected Ground structure) resonator with spiral ground pattern is used to shorten resonator size and improve circuit Q factor. And the equivalent circuit of BPF was suggested. The measured result shows good agreement with simulated data. Experimental results show the center frequency of 5.25GHz, the insertion loss of 0.14dB, and the 3-dB bandwidth of 350MHz (6%). The center frequency of BPF is 5.25GHz which is available for wireless LAN.

• Industrial Engineering and Management Systems
• /
• v.12 no.3
• /
• pp.234-243
• /
• 2013

In order to point out the best utility of a product (or a service), marketers need to clearly understand and measure the preference of the consumers. Among numerous marketing analysis techniques, the conjoint analysis is one of the popular tools for market research. One of the issues with this tool is the lack of feedback for the respondents. This paper proposes personal stepwise conjoint analysis based on an interactive Web-questionnaire allowing respondents to receive a diagnosis of their evaluation and giving the possibility to reconsider their evaluation. To validate our proposal, experimentation with forty-two respondents is also demonstrated. Experimental results, potential modifications and improvements are detailed in this paper.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.777-782
• /
• 2000

The flow fields in the volute casing of a small-size turbo-compressor at different flowrate (design point ${\pm}20%$) are studied by numerical analysis. The governing equations for three-dimensional steady viscous flow are solved using SIMPLE algorithm with commercial code of STAR-CD. Numerical results show that the three-dimensional flow pattern inside the volute casing of a small-size turbo-compressor is strongly influenced by secondary flows that are typically created by the curvature or the casing passages. The flow pattern in the casing also affects the performance of the turbo-compressor. In order to elucidate the loss mechanism through the volute, we prepared the secondary flow, velocity magnitude, and static pressure distribution at the four cross-sectional planes of the casing.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.271-275
• /
• 2004

In recent industry, according to pursuit the miniaturization and high-precision of machine part with development of new technology as IT and BT, the development of mold manufacturing technology for mass production is accompanied. This study proposes the design of micro mold-base, predicts the error of product through estimating transformation of injection process using FEM. Therefore the mold-base which is suitable for micro injection proposed in this study. Finally, the error of feature is analyzed by measuring the manufactured micro mold-base.