• Journal of Radiation Protection and Research
• /
• v.31 no.4
• /
• pp.203-210
• /
• 2006

Purpose : To estimate the dose to the embryo/fetus of a pregnant patient with brain tumors, and to design an shielding device to keep the embryo/fetus dose under acceptable levels Materials and Methods : A shielding wall with the dimension of 1.55 m height, 0.9 m width, and 30 m thickness is fabricated with 4 trolleys under the wall. It is placed between a Patient and the treatment head of a linear accelerator to attenuate the leakage radiation effectively from the treatment head, and is placed 1 cm below the lower margin of the treatment field in order to minimize the dose to a patient from the treatment head. An anti-patient scattering neck supporters with 2 cm thick Cerrobend metal is designed to minimize the scattered radiation from the treatment fields, and it is divided into 2 section. They are installed around the patient neck by attach from right and left sides. A shielding bridge for anti-room scattered radiation is utilized to place 2 sheets of 3 mm lead plates above the abdomen to setup three detectors under the lead sheets. Humanoid phantom is irradiated with the same treatment parameters, and with and without shielding devices using TLD, and ionization chambers with and without a build-up cap. Results : The dose to the embryo/fetus without shielding was 3.20, 3.21, 1.44, 0.90 cGy at off-field distances of 30, 40, 50, and 60 cm. With shielding, the dose to embryo/fetus was reduced to 0.88, 0.60, 0.35, 0.25 cGy, and the ratio of the shielding effect varied from 70% to 80%. TLD results were 1.8, 1.2, 0.8, 1.2, and 0.8 cGy. The dose measured by the survey meter was 10.9 mR/h at the patient's surface of abdomen. The dose to the embryo/fetus was estimated to be about 1 cGy during the entire treatment. Conclusion : According to the AAPM Report No 50 regarding the dose limit of the embryo/fetus during the pregnancy, the dose to the embryo/fetus with little risk is less than 5 cGy. Our measurements satisfy the recommended values. Our shielding technique was proven to be acceptable.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.30 no.4
• /
• pp.343-354
• /
• 2010

The present study was conducted to examine the fermentation characteristics and effective degradability (ED) in the rumen, and whole tract digestibility of whole crop silage based TMR in comparison with conventional separate feeding of concentrate and roughage. Three ruminally fistulated non-lactating Holstein cattle were used in a 3 $\times$ 3 Latin square design. The cattle were fed 8kg of whole crop barley silage based TMR (BS-TMR) or 8kg (DM basis) of whole crop rye silage based TMR (RS-TMR) twice (08:00 and 18:00) daily in an equal amount. The cattle were also fed concentrate (5.6kg) and rice straw (1.4kg) seperately (DM basis, Control) twice daily in an equal amount. The both silages were included in TMR at 20% level (as fed basis). pH in the rumen fluid was not influenced by the diets but was slightly higher from TMR than from control. No difference was found in ammonia-N concentration between diets. Total VFA concentration was relatively increased in the cattle fed RS-TMR to the other diets up to 6h post feeding. The proportion of acetate was increased in the TMR feeding at right before feeding (0 h, p<0.005) and 9 h (p<0.048) post feeding compared with control. Propionate proportion was increased (p<0.046) in both TMRs while butyrate proportion was increased (p<0.029) at 1h post feeding compared to other diets. Effective degradability (ED) of DM and CP of RS-TMR was relatively increased to other diets, and EDNDF of both TMRs was higher than that of control diet due to the increased parameters b (p<0.039) and c (p<0.006) in TMR treatments. Whole track digestibility of most components in the TMRs was slightly increased compared to that in control diet, and RS-TMR had a tendency to be increased whole track digestibility except for NDF compared to BS-TMR. Based on the results observed from the present study, nutrient availability of whole crop silage based TMR looked slightly better than conventional separate feeding of concentrate and rice straw, mainly due to the improved stabilization of fermentation in the rumen and increased NDF digestibility of whole crop silage in TMR.

• The korean journal of orthodontics
• /
• v.25 no.1 s.48
• /
• pp.73-85
• /
• 1995

Multi-Vertical Loop Arch Wire(MVLAW) is a kind of appliance for uprighting the mesially inclined posterior teeth axes simultaneously. In this study MVLAW was classified as 3 types by modifing the vertical loop design and named type A, B and C. Each MVLAW was fabricated from .017'x.025' TMA wire and preactivated at the distal end of the open vertical loop with 10 degree tip-back bend(type B has an electric welding stop at the distal end of each loop and type C has no electric welding stop). Type A MVLAW was preactivated at the apex of each open vertical loop with 10 degree tip-back bend(the electric welding stop of type A is positionod at the mesial side of each loop). The aim of the present study was to identify when and which MVLAW is more effective to correct the buccal segment axes simultaneously. The Photoelastic overview of the upper and lower right quadrant showed that stress concentrations were observed in its photoelastic model. The obtained results were as follows : 1. Higher level compression can be seen clearly at the distal curvature of the lower 1st and 2nd molar when A type MVLAW was applied without short class m elastic, but mild compression cannot be seen at the distal curvature of lower anterior teeth using the class m elastic. 2. Higher concentration was presented at the mesial curvature from the lower 1st premolar to the 2nd molar than the anterior teeth when B type MVLAW without short class III elastic was applied, but using the short class III elastic, higher concentration of compression was presented in the anterior teeth area. 3. Areas of higher compression and tension were not observed at the mesial and distal curvature of the entire 1ower teeth except lower central and lateral incisors in C type MVLAW without short class III elastic, but using the short class III elastic, higher concentration was seen at the mesial curvature of the lower 1st premolar and 1ower anterior teeth.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.36 no.2
• /
• pp.70-79
• /
• 2020

Purpose: The purpose of this study was to evaluate the effect of attachments and palatal coverage on stress distribution in maxillary implant overdenture using finite element analysis. Materials and Methods: Four maxillary overdenture 3-D models with four implants placed in the anterior region were fabricated with computer-aided design. 1) Ball-F: Non-splinted ball attachment and full palatal coverage, 2) Ball-P: Non-splinted ball attachment and U-shaped partial palatal coverage, 3) Bar-F: Splinted milled bar attachment and full palatal coverage, 4) Bar-P: Splinted milled bar attachment and U-shaped partial palatal coverage. Stress distribution analysis was performed with ANSYS workbench 14. 100 N vertical load was applied at the right first molar unilaterally and maximum stress was calculated at the implant, peri-implant bone and mucosa. Results: The use of the ball attachment showed lower maximum stress on implant and peri-implant bone than the use of the milled bar attachment. But it showed contrary tendency in the mucosa. Regardless of attachment, full palatal coverage showed lower maximum stress on implant, peri-implant bone and mucosa. Conclusion: Within the limitation of this study, ball attachment improved stress distribution on implant and peri-implant bone rather than milled bar attachment in maxillary implant overdenture. Also, full palatal coverage is more favorable in stress distribution.

• Horticultural Science & Technology
• /
• v.33 no.2
• /
• pp.268-275
• /
• 2015

We evaluated the effect of mixed liquid fertilizer (MLF) on growth responses of plants and soil chemical properties. To do so, a pot experiment with cherry tomatoes (Lycopersicon esculentum var. cerasiforme) using loam soil was conducted for 81 days in a temperature-controlled glasshouse, and four N fertilization treatments were laid out in a completely randomized design with three replicates: control (C), chemical fertilizer treatment (CF), and two rates (MLF-0.5 and MLF-1.0) of MLF treatment. Soils were periodically sampled and analyzed for pH, EC, total N, inorganic N and total C, and growth characteristics of cherry tomatoes were measured. During the experimental periods, the pH of MLF soils was higher than that of CF soils. Soil total-N content increased right after CF-application and ultimately decreased to the level of the control (C) soil, while MLF-application slightly increased the level of soil total-N and this level remained unchanged throughout the experiment. The levels of soil inorganic N content increased after application of CF or MLF, but the initial increase disappeared in 56 days after transplanting (DAT). The dry weight of shoots and roots increased in CF or MLF plants, while the number of fruit increased only in MLF plants. Whereas soluble solid contents were higher in MLF plants than in the other (C and CF) plants, the titratable acidity was not different among treatments. However, no consistent effect of N treatments on major elements of the organs of cherry tomatoes was found. The amounts of N taken up by plants were 0.91 g for CF, 0.61 g for MLF-1.0, 0.43 g for MLF-0.5, and 0.25 g for control treatments, resulting in greater N efficiency for CF than for MLF.

• Horticultural Science & Technology
• /
• v.31 no.3
• /
• pp.259-268
• /
• 2013

This study was carried out to evaluate the visual turfgrass's color quality, winter color, and spring green-up under three different soil systems and to make a practical use for sports turf design and construction. Several turfgrasses were evaluated in multi-layer, USGA and mono-layer systems. Turfgrass entries in the study comprised of 3 cultivars from Korean lawngrass (Zoysia japonica Steud.) of typical warm-season grass (WSG) and 3 blends and 3 mixtures from Kentucky bluegrass (KB, Poa pratensis L.), perennial ryegrass (PR, Lolium perenne L.), and tall fescue (TF, Festuca arundinacea Schreb.) of cool-season grass (CSG). Significant differences were observed in the turfgrass's color quality, winter color, and spring green-up in the study. Seasonal variation of visual turf color greatly occurred according to soil systems and turfgrasses. Multi-layer and USGA systems were highly associated with better visual color ratings, as compared with mono-layer system. Regardless of soil system, visual turf color in all entries was better from spring to fall than in winter. Great color differences were observed during a period of early December to early spring. CSG produced a better color quality over WSG in any soil system. Overall color ratings for CSG were KB > PR > Mixtures > TF. As for a winter color, its ranking was USGA > multi-layer > mono-layer system. No difference was found in winter among cultivars of Korean lawngrass, being completely brown, but great differences among CSG. Rated best for winter color was PR, followed by CSG mixtures, KB and finally TF in order. It was generally conceded that fast green-up in spring was greatly related with multi-layer over mono-layer system and also CSG over WSG. Among CSG, TF had a fastest green-up. PR was also fast in green-up, but poor in color uniformity. KB, however, was the slowest due to shallow rooting system, when compared with other CSGs. These results demonstrate color differences were greatly variable according to soil systems and also among turfgrass species. A precise decision should be made in selecting turfgrass species and soil system. Multi-layer and USGA systems were considered as the suitable one for turfgrass color quality, winter color and spring green-up. It is a great necessity to combine proper soil system, right turfgrass species, and appropriate mixing rates by a concept-oriented approach, when establishing garden, parks, soccer field, and golf courses and so on.

• Journal of Biosystems Engineering
• /
• v.2 no.1
• /
• pp.7-24
• /
• 1977

This paper is the forth and fifth one of the study on balanced type oscillating mole drainer. In the light of the results from previous reports about the model tests, some design criteria were established and a prototype machine was set up for experimental purpose. Motion characteristics and functionof the each parts of the machine were checked and analyzed. After that, performance tests of the prototype machine were carried out in thefield. Obtained results are summarized as follows ; 1. Ten centimeter of the bullet diameter was determined so as to be able to attach it to the tractors with capacity of 30 PS to 40 PS. 2. To maintain the balance between the moments of the front shank and rear shank, the oscillating amplitude of the rear bullet was determined to be larger than that of the front bullet. At the same time , the oscillating direction of the rear bullet was designed with the inclines of ten to thirty degrees. 3. An octagonal dynamo transduced was developed for measuring the compressive force of the upper link is measuring the draft force of the machine. Acceptable linear relationship between forces and strain responses from O.D.T. was obtained. 4. Analysing the balancing mechanism of the acting part of the machine , it was found that the total draft force of the machine was equal to the difference between the sum of the draft force produced from the right and left side bending moments of the lower drawber and the compressive force on the upper link. 5. There are acceptable linear relationship between the strain and twisting moment by driving shaft, and between strain and shank moment. Above results enable us to carry out the field experiment with prototype machine. 6. When the test machine was used in the field, it was possible to reduce the oscillating acceleration by forty percent in average as compared it with the single bullet mole drainer. 7. When the test machine was used under the oscillating condition, the dratt torce was reduced by 27 percent to 59 percent as compared it with the test machine under non-oscillating condition, while the draft force was increased by 7 percent to 20 percent as compared it with the mole drainer having oscillating single bullet. The reasoning behind this fact was considered as the resistance force due to the rear shank and bullet. 8. As the amplitude and frequency of the bullet were increased, the torque was increased accordingly. This tendency could be varied with the various characteristics of the given soils. And the larger frequency and amplitute, the more increasing oscil\ulcornerlating power but decreasing draft brce were needed, and draft force was increased as the velocity was increased.9. When the amplitude of the rear bullet was designed to be larger than that of the front bullet, the minimum value of the moment was lowered and oscillating acceleration was reduced. And when the oscillating direction of the rear bullet was declined back\ulcornerwards, oscillating acceleration was increased along with the increasing angle of decli\ulcornernation. When the test machine was operated in high speed, the difference between maximum moments and minimum ones became narrow. This varying magnitude of moments appeared on the moment oscillogram seems to be correlated to the oscillating acceleration and draft force. 10. From the analysis of variance, it was found that those factors such as frequency, amplitude, and operating velocity significantly affected in the oscillating acceleration, the draft resistance, the torque, the moment, and the total power required. And interaction between frequency and amplitude affected in the oscillating acceleration. 11. Within the given situation of this study, the most preferable operating conditions of the test machine were 7 Hz in oscillating frequency, 0.54 m/sec in operating velocity, and 39.1 mm in oscillating amplitude of front and rear bullets. However, it is necessary to select the proper frequency and magnitude of oscillation depending on the soil properties of the field in which the mole drainer is practiced by use of a bal1nced type oscillating mole drainer. 12. It is recommended that a comparative study of the mole drainers would be performed in the near future using two separate balanced oscillating bullet with the one which is operated by oscillating the movable bullet in a single cylinder or other balanced type which may be single oscillating bullet with spring, damper or balancing weight, and that of thing. To expand the applicability of the balanced type oscillating mole drainer in practical use, it is suggested to develop a new mechanism which perform mole drain with vinyl pipe or filling material such as rice hull.

• Women's Health Nursing
• /
• v.1 no.2
• /
• pp.200-221
• /
• 1995

The confusion of the sense of value on sex is increasing because of the rapid change in social-cultural environment. Also due to a rise in the standard of living, the age of adolescence is getting lower, and so the second sexual marks appear to primary schoolers. At this time in the aspect of the education for the whole man, it's very important for primary schoolers to acquire right knowledge and desirable attitude on sex so that can overcome psychological instability caused by physical growth, be responsible for their behaviors and lead happy lives. This study was made to find out the effects of sex education for the primary schoolers' knowledge and attitude about sex. The study was designed as simulated control group pretest-posttest design, which only pretest was practiced to control group and after sex education only posttest was practiced to experimental group. The data was collected for 18 days from March 13, 1995 to March 31, 1995. The subjects of this study were 130 six-graders in a private primary school in seoul. The control group and experimental group were composed of 65 pupils, each. Sex education consisted of lecture and discussion and the materials were this researcher's own made, 'How do I grow? and related OHP film and video. This education was practiced 40 minutes at a time, at intervals of 2-4 days' six times during 3weeks. For sex knowledge tools, 20 item questionaries on the base of related reference books and contents of this study were used. For sex attitude tools, this researcher's own made 13 item questionaries were used which were revised and complemented and laying stress on the reference books. The data was analyzed through pc-SAS program. The homogeneity test in terms of the general characteristics of experimental and control group was analyzed through $x^2$-test and t-test. And the difference in the primary schoolers' score on knowledge and attitude about sex before and after the sex education was analyzed through t-test and ANCOVA. The results of this study are as follows : 1. The result of the homogeneity test in terms of the general characteristics of the experimental and control group showed that there were significant differences in economic standard($x^2$=2.92, P=0.052) and brotherly ties($x^2$=3.78, P=0.052). 2. Hypothesis 'After sex education, the score of primary schoolers' sex knowledge will be higher than before. 'showed statistically significant difference.(t=11.99, P=.0001) Sex education was practiced under control over subjective view of economic standard and brotherly ties which showed significant difference at the homogeneity test in terms of the general characteristics between the two groups. After this education, the results of comparing the score of primary schoolers' sex knowledge also showed significant difference between the two groups. So hypothesis I was supported since primary schoolers to have education showed noticeable results in the sex knowledge score. (F=16.52, P=.0001) 3. Hypothesis 'After sex education, primary schooler's sex attitude score will be higher than before' showed statistically significant(t=5.08, P=.0001) Sex education was practiced, too, under control over subjective view of economic standard and brotherly ties which showed significant difference at the homogeneity test in terms of the general characteristics between the two groups. Bat this time the results of comparing the primary schoolers' sex attitude showed no significant difference between the two groups. So hypothesis II was rejected since for primary schoolers to have sex education showed no noticeable results in sex attitude score. (F=3.52, P=.0628) These results of the study show that sex education gives affirmative change to the primary schooler's sex knowledge, bat short periods' sex education doesn't give any change to the sex attitude. For the establishment of the pupils' desirable sex attitude, systematic and concrete sex education fit for the pupils' developing stage should be practiced over a long period of time.

• Korean Journal of Poultry Science
• /
• v.40 no.4
• /
• pp.351-359
• /
• 2013

This study was undertaken to assess dietary crude protein (CP) and amino acid (AA) concentrations for growth performance and carcass characteristics in Korean native ducks. In a $2{\times}3$ factorial arrangement, 1-d-old Korean native male ducks were allotted to 6 dietary treatments in a completely randomized design. Experimental diets contained 23 or 21% CP with 1.31/1.09, 1.21/1.00, 1.11/0.91 and 1.11/0.91, 1.02/0.83, 0.92/0.75 AA (Lysine/Total sulfur amino acid, Lysine/TSAA), respectively, from 0 to 3 wk of age. From 4 to 8 wk of age, experimental diets had 19 or 17% of diet; each contained 1.00/0.79, 0.94/0.75, 0.88/0.71 and 0.88/0.71, 0.82/0.67, 0.76/0.63 AA (Lysine/TSAA), respectively. Each dietary treatment has 6 replicates and feed and water were provided ad libitum. Body weight (BW), feed intake and uniformity were measured at 3 wk and 8 wk and carcass characteristics were evaluated at 8 wk of age. As CP increased from 21 to 23%, the BW and BW gain significantly increased (P<0.05) during 0 to 3 wk of age. From 4 to 8 wk of age, BW, feed intake, BW gain, feed conversion rations (FCR) and uniformity were not different (P>0.05) between treatments. Carcass yield and relative weights of liver, spleen, right breast and leg per 100 of BW were not different (P>0.05) between treatments. The meat color, shear force value, cooking loss and pH were not affected by dietary treatments (P<0.05). Korean native ducks require relatively low levels of dietary CP and AA for late growth and carcass yield due to low daily weight gain. This suggests the possible differences in CP and AA needs between Korean native ducks and commercial breeds from foreign breeding companies, especially late growth stage.

• Journal of Korean Ophthalmic Optics Society
• /
• v.18 no.4
• /
• pp.449-456
• /
• 2013

Purpose: The present study aimed to investigate the effects of corneal eccentricity and shape on the rotational pattern of toric soft lens by the postural change of lens wearers. Methods: The corneal eccentricity of 41 eyes (aged 20s) having -1.0 D with-the-rule corneal astigmatism (WRCA) was measured, and then toric soft lenses were fitted with the amount of total astigmatism. In lying and straight postures, the rotation of toric soft lenses was recorded by a camera attached to slitlamp and analyzed. Results: Most toric soft lens designed with accelerated stabilization rotated to the temporal direction, which was the lying position direction, regardless of corneal eccentricity, and some lenses rotated to the nasal direction for high corneal eccentricity and corneal type of asymmetric bowtie. There was no correlation between the amount of rotation and corneal eccentricity right after of contact lens wearing in straight and lying posture, however, the amount of rotation was the greater for the cornea with the higher eccentricity after the subjects laying down for some period. The speed of lens rotation started to decrease after the subjects laying down, but the speed was not different according to corneal eccentricity difference. The amount of lens rotation for symmetric and asymmetric bowtie-typed corneas increased more than it for oval-typed cornea, and it was same even with time elapsing. The speed of lens rotation in lying posture was the slowest in asymmetric bowtie-typed cornea compared with other corneal types. Conclusions: From the present study, it was revealed that the rotational pattern of toric soft lens was affected by corneal eccentricity and corneal shape when the wearer's posture changed. Thus, it should be considered for the development of the fitting guideline and the design of toric soft lens.