• Structural Engineering and Mechanics
• /
• 제58권6호
• /
• pp.967-988
• /
• 2016

Due to the significant aerodynamic interference from sub-towers and surrounding tall buildings, the wind loads and dynamic responses on main tower of three-tower connected tall building typically change especially compared with those on the isolated single tall building. This paper addresses the wind load effects and equivalent static wind loads (ESWLs) of three-tower connected tall building based on measured synchronous surface pressures in a wind tunnel. The variations of the global shape coefficients and extremum wind loads of main tower structure with or without interference effect under different wind directions are studied, pointing out the deficiency of the traditional wind loads based on the load codes for the three-tower connected tall building. The ESWLs calculation method based on elastic restoring forces is proposed, which completely contains the quasi-static item, inertia item and the coupled effect between them. Then the wind-induced displacement and acceleration responses for main tower of three-tower connected tall building in the horizontal and torsional directions are investigated, subsequently the structural basal and floor ESWLs under different return periods, wind directions and damping ratios are studied. Finally, the action mechanism of interference effect on structural wind effects is investigated. Main conclusions can provide a sientific basis for the wind-resistant design of such three-tower connected tall building.

• Journal of Welding and Joining
• /
• 제19권1호
• /
• pp.112-117
• /
• 2001

The factor affecting on the fatigue strength of spot welded specimen have been studied. To analyze and predict crack initiation position and propagation directions on the spot welded area are very important for strength design of the automobile body structure. In fact, there are a various of loads in running automobile but, it is impossible to replay like an actual conditions in the laboratory. So, in this study tensile-shear type and in-plane bending type specimens were used in fatigue test and includes an analysis of fatigue crack initiation position and propagation directions about earth specimens. The results obtained in the present study are summarized as follows: 1. In tensile-shear type fatigue test, the region of fatigue crack initiation position was affected by out-of-plane bending deformation due to bending angle. 2 In in-plane bending type fatigue test, the behavior of fatigue crack initiation position and propagation derections due to angle between upper plate and lower plate was dominated by magnitude of in-plane bending moment.

• 제어로봇시스템학회논문지
• /
• 제15권5호
• /
• pp.543-547
• /
• 2009

This paper describes the design, simulation, development, and experiment of a six degree-of-freedom micropositioning parallel manipulator. A movable stage was supported with six links, each of which extends with a dc-servo micropositioning actuator. In case of parallel manipulator, while the solution of the inverse kinematics is easily found by the vectors of the links which are composed of the joint coordinates in base and platform, but forward kinematic is not easily solved because of the nonlinearity and complexity of the parallel manipulator's kinematic output equation with the multi-solutions. The movable range of the prototype was ${\pm}25mm$ in the x- and y-directions and ${\pm}12.5mm$ in the z-direction. The minimum incremental motion of the prototype was $1{\mu}m$ in the x- and y-directions and $0.5{\mu}m$ in the z-direction. The repeatability of the prototype was ${\pm}2{\mu}m$ in the x- and y-directions and ${\pm}1{\mu}m$ in the z-direction. The motion performance was also evaluated by not only the computer simulation of CAD model but also the experiment using a capacitive sensor system.

• 한국CDE학회논문집
• /
• 제20권4호
• /
• pp.348-356
• /
• 2015

It is important to devise methods for assisting dentists to consistently determine implant positions and directions and to accurately perform drilling tasks during dental implant surgery. In this paper, we propose a novel approach to tooth implant placement planning which deals with the determination of the positions and directions of multiple implant fixtures for a set of missing mandibular teeth and suggests the selection of the sizes and types of the implant fixtures. We combine Korean standard data in the sizes and positions of human teeth with the patient specific 3D models of mandibular jawbones, nerve curves, and neighboring teeth around the missing teeth in order to determine the positions and directions of the implant fixtures for the missing teeth. Using the geometric and spatial information of the jawbones, the teeth and the implant fixtures, we can construct the 3D models of surgical guide stents which are crucial to perform drilling tasks with ease and accuracy. Adopted in 3D simulation of dental implant placement, the approach can provide surgeon students with good educational contents. We also expect that, with further work, the approach can be used as a useful tool to plan for dental implant surgery.

• 한국의상디자인학회지
• /
• 제21권4호
• /
• pp.17-26
• /
• 2019

This research aims to obtain useful data on the development of compression garment products with high-stretch knitted materials. Using nylon SCY, four specimens were knitted. Then, appearance (width, length, weight, thickness), stretch property (stretch, recovery) and clothing pressure were measured and their interrelation was analyzed. In the comparison of appearance features, yarn floating caused shrinkage in both course and wale directions of the specimens. Yarn overlapping by tucking caused a release in the course direction and shrinkage in the wale direction. Also, structural change was affected by the weight and thickness change of the knitted fabric. In the analysis of fabric stretch, yarn floating reduced the extension in course direction and increased that in wale direction of the knitted fabric. However, yarn overlapping reduced the elongation in both directions. In the analysis of recovery, yarn floating and overlapping raised fabric recovery in both directions, and tuck structure was superior to float in recovery. In the analysis of clothing pressure, 'Plain-Float' structured fabrics showed a higher clothing pressure than 'Plain' and the clothing pressure value of 'Plain-Tuck' was lower than that of 'Plain'. As for the correlation between fabric appearance, stretch property, and clothing pressure, the appearance change in course direction had a major influence on the clothing pressure. The shrinkage of appearance led to a decrease in stretch and an increase in clothing pressure.

• Journal of the Optical Society of Korea
• /
• 제10권2호
• /
• pp.67-75
• /
• 2006

A dedicated catadioptric panoramic lens with the rectilinear projection scheme is designed. The resolution is high enough to provide separate VGA quality images for the respective four directions and the image distortion is less than 0.5%.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표논문집(II)
• /
• pp.405-411
• /
• 1998

An iterative numerical computational algorithm is presented to design a plate of shell element subjected to membrane and flexural forces. Based on equilibrium consideration, equations for capacities of top and bottom reinforcements in two orthogonal directions have been derived. The amount of reinforcement is determined locally, i. e., for each sampling point, from the equilibrium between applied and internal forces. One case of design is performed for a hyperbolic paraboloid saddle shell (originally used by Lin and Scordelis) to check the design strength against a consistent design load, therefore, to verify the adequacy of design practice for reinforced concrete shells. Based on nonlinear analyses performed, the analytically calculated ultimate load exceeded the design ultimate load from 14-43% for an analysis with relatively low to high tension stiffening, ${\gamma}$ =5~20 cases. For these cases, the design method gives a lower bound on the ultimate load with respect to Lower bound theorem. This shows the adequacy of the current practice at least for this saddle shell case studied. To generalize the conclusion many more designs-analyses are performed with different shell configurations.

• 한국실내디자인학회:학술대회논문집
• /
• 한국실내디자인학회 2006년도 추계학술발표대회 논문집
• /
• pp.81-85
• /
• 2006

This paper aims to analyze ecological characteristics of interior design, selecting as the subjects Busan-based construction companies which have a model house, among those that distribute apartments in Busan as of August 2006. Primarily, literature research Is conducted to understand recent trends of interior design for apartment building, present situations and characteristics of ecological design, and prepare environmentally-friendly guidelines and check-list items on the basis of domestic and overseas cases. Collected data in turn is analyzed to assess ecological characteristics of apartment building design in Korea today and present problems and directions for the future.

• 한국주거학회:학술대회논문집
• /
• 한국주거학회 2008년도 춘계학술발표대회 논문집
• /
• pp.360-363
• /
• 2008

The purpose of this study was to evaluate current usages and situations of kitchen with regard to universal design concept in order to provide useful data to plan universally designed kitchen space for all family members. Previous studies for universal design and kitchen planning were reviewed and a checklist was developed to evaluate kitchen space based on universal design concept by researchers of this study. Also, all items in the checklist were reclassified by 5 universal design criteria(Supportiveness, Adaptability, Communicability, Pleasantness, and Accessibility) and analyzed sample kichens by the criteria. The 7 households with different characteristics*age, sex, degree of disability or aging, and number of family) were selected for case studies. The results of this study suggested several critical design points to establish directions or provide guidelines for further kitchen planning.

• 한국실내디자인학회논문집
• /
• 제29호
• /
• pp.112-119
• /
• 2001

In general, the definition of criticism is making a constructive analysis between good & evil, right & wrong, and beauty & ugliness. Just as the literature, art, music, and architecture welcomes productive criticism in order for further advancement in each professional field, constructive criticism in the field of interior architecture must be activated stance it would be as useful as in other fields to upgrade the level of design quality If the constructive criticism were to be taken properly in the benefit of further advancement in particular design, then the criticism must hale a proper criteria in order to examine and review the design work objectively However, as the design symbolizes cultural interpretation and reaction towards better creativity, we expect design to be mutated in many different directions. As the limit of Interior architecture shares limitless possibilities in today's society, it seems that we need to set up a guidelines of design criticism in order to support the further development of the area of interior architecture.