• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.2
• /
• pp.178-181
• /
• 1986

Dielectric waveguide gratings of the image-guide type can be made by periodically cutting notches on the sides or in the top is the image guide. In this paper modeling of grattings using a transmission-line equivalent circuit with equal line lenghth is biscussed, and systematic design procedure of dielectric-waveguide bandpass filter using coupled gratings is presented. It is shown that experimental results is in excellent agreement with the computed response.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.1
• /
• pp.15-22
• /
• 1991

New design method of small-sized 3-dB $0^{\circ}/180^{\circ}$ ring hybrid and Wilkinson power divider using both lumped elements and distributed elements are presented. At the center frequency of 900 MHz 3-dB $0^{\circ}/180^{\circ}$ ring hybrid and Wikinson power divider are designed and tested. Good agreements are obtained between measured and theoretical modeling results, and at the same time the circuit area is reduced by more than 70% compared with the discributed-type circuits.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.181-184
• /
• 2001

A coplanar waveguide(CPW) on a dielectric substrate consists of a center strip conductor with semi-infinite ground planes on either side. This type of waveguide offers several advantages over microstrip line. It facilitates easy shunt as well as series mounting of active and passive devices. It eliminates the need for wraparound and via holes, and it has a low radiation loss. These, as well as several other advantages, make CPW ideally suited for microwave integrated circuit applications. However, very little information is available in the literature on models for CPW discontinuities. This lack of sufficient discontinuity models for CPW has limited the application of CPW in microwave circuit design. We presented for the characteristics of coplanar waveguide open end capacitance and series gap capacitance. Measurements by utilizing the resonance method were made and the experimental data confirmed the validity of theories. The relationships between the CPW capacitances and the physical dimensions were studied.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.914-917
• /
• 1999

The paper describes a 17 $\times$ 17-b multiplier using the Radix-4 Booth’s algorithm. which is suitable for 32-bit RISC/DSP microprocessors. To minimize design area and achieve improved speed, a 2-stage pipeline structure is adopted to achieve high clock frequency. Each part of circuit is modeled and optimized at the transistor level, verification of functionality and timing is performed using HSPICE simulations. After modeling and validating the circuit at transistor level, we lay it out in a 0.35 ${\mu}{\textrm}{m}$ 1-poly 4-metal CMOS technology and perform LVS test to compare the layout with the schematic. The simulation results show that maximum frequency is 330MHz under worst operating conditions at 55$^{\circ}C$ , 3V, The post simulation after layout results shows 187MHz under worst case conditions. It contains 9, 115 transistors and the area of layout is 0.72mm by 0.97mm.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.11a
• /
• pp.23-27
• /
• 2000

Simultaneous Switching Noise (SSN) propagated through parallel power and ground planes in high-speed multilayer printed circuit boards (PCBs) causes malfunction of both digital and analog circuits. To reduce SSN, decoupling capacitors are generally used in the PCBs. In this paper, we improve the equivalent circuit model of decoupling capacitor in high-frequency range to analyze the effect of SSN reduction accurately. The analysis is performed by the microwave and RF design system (MDS) method and the finite difference time domain (FDTD) method. We compared the results by the ideal capacitor model with those by the proposed model.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.3
• /
• pp.25-32
• /
• 1992

In UHF, VHF new design method of samll-sized 3-dB 0$^{\circ}$/180$^{\circ}$ ring hybrid terminated arbitrary impedance using both lumped elements and distributed elements is presented. At the center frequency of 900 MHz, 3-dB 0$^{\circ}$/180$^{\circ}$ ring hybrid terminated arbitrary impedance is designed, analyzed and tested. Good agreements are obtained between measured and theoretical modeling results, and at the same time, the circuit area of hybrid fabricated with two dimensional parallel coupled line, distributed elements and lumped elements is reduced by more than 70% compared with only distribyted-type circuits.

• The KSFM Journal of Fluid Machinery
• /
• v.16 no.2
• /
• pp.35-41
• /
• 2013

Inlet part of a printed circuit heat exchanger has been optimized by using three-dimensional Reynolds-Averaged Navier-Stokes analysis and surrogate modeling techniques. Kriging model has been used as the surrogate model. The objective function for the optimization has been defined as a linear combination of uniformity of mass flow rate and the pressure loss with a weighting factor. For the optimization, the angle of the inlet plenum wall, radius of curvature of the inlet plenum wall, and width of the inlet pipes have been selected as design variables. Twenty six design points are obtained by Latin Hypercube Sampling in design space. Through the optimization, considerable improvement in the objective function has been obtained in comparison with the reference design of PCHE.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1673-1675
• /
• 2004

The design, modeling and measurement of RF switch module for GSM applications is presented in this paper. RF switch module is constructed using a LTCC multi-layer switching circuit and integrated low pass filter. Insertion and return loss of the low pass filter were designed less than 0.3 dB and better than 12.7 dB at 900 MHz. The RF switch module contained 10 embedded passives and 3 surface mount components integrated on $4.6{\times}4.8{\times}1.2$ mm, 6-layer multi-layer integrated circuit. The insertion loss of switch module was measured at 900 MHz was 11 dB.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.250-254
• /
• 2001

The resolution of analog sensor is determined by its sensitivity and amplitude of noise. This paper presents modeling of inductive gap sensor base on equivalent magnetic circuit and analysis of sensitivity. We can simulate static characteristic of inductive gap sensor using this model. Computer simulation show that sensor's sensitivity is affected by magnetic flux's leakage and fringing, and that they are affected by shape of sensor probe. Base on this, we designed shape of inductive position sensor probe.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.4
• /
• pp.823-828
• /
• 2011

We have systematically designed and experimentally demonstrated the opto-electrical predistortion optical transmitter using microwave circuit modelling for reducing the nonlinearity of the distributed-feedback laser diode (DFD-LD). The DFB-LD is analyzed using microwave circuits model based on rate equations. Through the system-level simulation for predistortion method, the optimized characteristics of the RF components in the system are confirmed. The simulated and experimental results show the reduced distortion products. These results are analyzed as the evaluation parameters for the miniaturization and optimization of the opto-electrical predistortion method in radio-over-fiber systems.