• ETRI Journal
• /
• 제38권4호
• /
• pp.654-664
• /
• 2016

This paper presents a transformer-based reconfigurable synchronous boost converter. The lowest maximum power point tracking (MPPT)-input voltage and peak efficiency of the proposed boost converter, 20 mV and 88%, respectively, were achieved using a reconfigurable synchronous structure, static power loss minimization design, and efficiency boost mode change (EBMC) method. The proposed reconfigurable synchronous structure for high efficiency enables both a transformer-based self-startup mode (TSM) and an inductor-based MPPT mode (IMM) with a power PMOS switch instead of a diode. In addition, a static power loss minimization design, which was developed to reduce the leakage current of the native switch and quiescent current of the control blocks, enables a low input operation voltage. Furthermore, the proposed EBMC method is able to change the TSM into IMM with no additional time or energy loss. A prototype chip was implemented using a $0.18-{\mu}m$ CMOS process, and operates within an input voltage range of 9 mV to 1 V, and an output voltage range of 1 V to 3.3 V, and provides a maximum output power of 37 mW.

• 한국안전학회지
• /
• 제19권2호
• /
• pp.93-97
• /
• 2004

Slab formwork consists of sheathing, stringer, hanger and shore. There are several types of adjustable individual shores. In constructions site, pipe supports are usually used as shores. The strength of a pipe support is decreasing as it is frequently being used at the construction site. In this study, 2857 pipe supports were bought to fine out the strength change of used pipe support and unused pipe supports according to aging. Among these pipe supports, 2337 pipe supports were lent to the construction companies free of charge. Compressive strength was measured by knife edge test and plate test at each 3 month. Test results show that the strength of unused pipe supports almost equaled to the strength of new pipe supports until 191 days, but the strength of used pipe supports at 191 days was lower than the strength of new pipe supports. So, the strength of used pipe supports at 191 days was not satisfied the specification of KS F 8001. According to these results, it shows that attention has to be paid to formwork design using used pipe supports. Therefore, the paresent study results will be able to provide a firm base to design slab formwork and test the performance of used temporary structure and prevent formwork collapses.

• 한국실내디자인학회논문집
• /
• 제24권2호
• /
• pp.142-150
• /
• 2015

The purpose of this study is to analysis the change of rural house type and house plans in Bonghwa province. According to definition of rural area, the scopes of the research of rural houses limited the Bonghwa rural area(1 eup, 9 myeon). The method of study is to compare and analyze about housing situation, structure of house, housing type and construction of house space etc. through the statistical data of Bongwha statistical yearbook, space syntax(convex analysis) and other various data etc. during these 10 years. As a results of the analysis 1) According to Change of family member the supply ratio of detached house is steadily decreasing and changing from a detached house to multi-household house in Bongwha areas. 2) Most of houses structure were using lightweight steel construction because of cost-cutting of construction and easy way to construct etc.. 3) The highest Integration space is living space in rural house plans 4) The highest segregation space is bathroom space of master bed room in rural house plans. Some of bed rooms are classed as segregation space regardless of Integration space 5) Traditional front yard's function is changing from the place with the various functions to the place with the specific functions.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 가을 학술발표회 논문집
• /
• pp.362-367
• /
• 1994

In Precast Concrete Structure, safety of structure depends on strength of joint. Asa result, there exists a necessity to review the effects of elements consisting joints, since these elements are important factors for evalaution of joint strength. However, there elements are different for construction methods and may be changed even during construction. Obviously, the change of elements can cause the change of joint strength; yet, the effects of the variables are not clearly defined. The behavior of the joints are complicated and evaluated only through experiments. Consequently, the main objective of this paper is to review effects of components consisting Precast Joints, I order to keep higher joint strength than specified in the design code.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.244-249
• /
• 1997

Internal and external heat sources will cause to deform to machine elements in the contact joint of structure,which results in the change of contact pressure distribution different from initial assembly. Heat induced variations of contact pressure will change the static and dynamic properties such as contact stiffness,damping as well as contact heat conduction in the structure. In order to design and control the intelligent machine tool operating in variant conditions more sophisticatedly, the good prediction for the changes of prescribed propeties are strongly required especially in the contact elements adjacent to the rotational or linear bearing This paper presents some computational and experimental results in regard to static and dynamic characteristics of the press-fitted bush and shaft assembly which is a model of the bearing innerrace and shaft assembly. In the condition of heat generation on the outer surface of the bush,the effects of changes in the negative clearance and the heat flux on pressure distribution and dynamic properties are investigated. Results of this study show that the edge effect of the bush and the initial clearance have effects on the transient dynamic characteristics significantiy.

• 반도체디스플레이기술학회지
• /
• 제7권2호
• /
• pp.39-43
• /
• 2008

Productivity is one of the performance indices of the semiconductor equipment in manufacturing viewpoint. Among many ways tried and adopted for improvement of the productivity of the FAB equipment, variation of equipment configuration was considered and its effect on the throughput was analyzed. Parallel machine cycle charts that were generated based on the equipment log were used in the analysis. Efficiency of the equipment due to change of the structure and the probability of the usage in the manufacturing process were examined. The results showed that the modification of the control algorithm in the equipment and the redistribution of the process time for each process and transfer module along to the change in the structure enhance the throughput of the equipment.

• Journal of the Korean Statistical Society
• /
• 제32권2호
• /
• pp.175-191
• /
• 2003

An empirical Bayesian approach is discussed for estimation of characteristics from the two-way balanced rotation sampling design which includes U.S. Current Population Survey and Canadian Labor Force Survey as special cases. An empirical Bayesian estimator is derived for monthly effect under presence of two types of biases and correlations It is shown that the marginal distribution of observation provides more general correlation structure than that frequentist has assumed. Consistent estimators are derived for hyper-parameters in Normal priors.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 2001년도 학술발표회 논문집(Proceedings of the Korean Textile Conference)
• /
• pp.141-144
• /
• 2001

• 대한기계학회논문집A
• /
• 제34권7호
• /
• pp.873-879
• /
• 2010

일반적으로 설계파라미터 변경에 의한 구조물의 동특성변화를 예측하는 연구에 비해 동특성 변화로부터 변경된 설계파라미터를 예측하는 연구는 잘 알려져 있지 않다. 여기에서는 감도계수와 반복법을 사용하여 비례감쇠계의 변경된 설계파라미터를 예측하였다. 감도계수는 변경에 의한 고유벡터의 변화로부터 구하였다. 이 방법을 3 층 전단 구조물에 적용하여 변경된 설계 파라미터를 예측하였으며 재 해석한 결과와 잘 일치함을 알았다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.502-505
• /
• 2007

In this paper we propose a novel electrode structure for high transmittance in the Patterned Vertical Alignment (PVA) LC cell. Normally, the transmittance of PVA LC cell is depended on the shape of the electrode and cell gap. We studied the area decreasing the transmittance through the electrode structure for wide viewing angle and proposed new electrode design to change LC director configuration in the area. We use the 'TechWiz LCD' for calculation of the director configuration and optical characteristics. We show the comparison of the calculated optical transmittance between the conventional PVA mode and the proposed PVA mode. From the results, we confirm that the optical transmittance of the proposed structure of the PVA cell becomes higher.