• Journal of the Korean Vacuum Society
• /
• v.7 no.4
• /
• pp.314-319
• /
• 1998

TiN thin films were deposited on SKD 61 steel substrates by reactive sputtering under various deposition conditions, and subsequently their growth characteristics and properties were studied. Deposition rate was proportionally increased with total gas pressure as well as RF input power, while the increase of nitrogen in the reaction gas induced a significant suppression of deposition rate. The resulted films exhibited hillocks on the surface. The TiN film prepared using a typical deposition condition showed a (111) preferred orientation and maintained the stoichiometry of pure TiN.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.21.1-21.1
• /
• 2011

Vertically aligned single-crystal ZnO nanowires have been successfully grown on c-plane sapphire substrate using chemical vapor deposition (CVD) without catalyst. According to growth temperatures, it was changed ZnO growth characteristic. We investigated the effect of substrate temperatures on the growth ZnO films or nanowires on c-plane (0001) sapphire substrates. The ZnO films were acquired at $500^{\circ}C$, whereas the ZnO nanowires were obtained at $600^{\circ}C$, $700^{\circ}C$, and $800^{\circ}C$. The growth behavior diameter and growth rate of ZnO were changed due to different temperature. As a result of analyzing in-plane residual stress by X-ray diffraction, the optimized condition of ZnO nanowires were at $600^{\circ}C$.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05b
• /
• pp.159-164
• /
• 1997

Pyrolytic carbon layer was coated on A1203 balls by fluidized bed type chemical vapour deposition unit to develop the coating technology for the preparation of coated nuclear fuel. The deposition was carried out at the temperature ranges between 110$0^{\circ}C$ and 130$0^{\circ}C$ with various gas contents and flow rates. Source and carrier gas were propane and argon, respectively. X-ray analysis shows that the deposition layer was typical carbon spectra. The growth rate of carbon layer depended on the amount of source gas and the deposition temperature. For the alumina balls with 2mm in diameter, the deposition rate was 11${\mu}{\textrm}{m}$/hr in the flow gases containing 30% source gas at 130$0^{\circ}C$ with a total flow rate of 2.0$\ell$/min. Microstructural observation of the deposits with scanning electron microscope revealed that the deposits had relatively dense and isotropic structure. Chemical analysis by energy dispersive spectroscopy showed that the layer was pure carbon.

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.2
• /
• pp.55-63
• /
• 1985

This study is focused on deposition process leading to inefficiency and hot corrosion in fossil fuel-fired furnaces and engines. An improved understanding of the coupled thermodynamics, kinetics, and transport processes governing the deposition rate of inorganic oxides and salts from hot gases containing these compounds can suggest more efficient test strategies and control measures. Accordingly, an optical re-evaporation method for accurately measuring the growth rate of deposits under laboratory burner conditions has been developed. To demonstrate the technique and provide data suitable for theoretical model development, a deliberately simple chemical system and target geometry are used. Potassium sulfate(K$_{2}$SO$_{4}$)is introduced into a premixed propane-air flat flame at atmospheric pressure. The growth rate of $K_{2}$SO$_{4}$ on an electrically heated Pt ribbon is measured by re-evaporation technique.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1991.10a
• /
• pp.63-67
• /
• 1991

Amorphous silicon films were deposited on glass, [100] single crystal silicon wafer with thermally grown silicon dioxide, and [100] silicon wafer substrates by Plasma Enhanced Chemical Vapor Deposition(with argon diluted silane source gas). Growth rate, UV optical band edge, and the hydrogen quantity in the amorphous silicon films have been investigated as a function of the preparation conditions by measuring film thickness, UV-absorbency, and FT-IR transmittance. The growth rate of the ${\alpha}$-Si:H films increases with increasing substrate temperture, flow rate and R.F. power density. The UV optical band edge shifts to blue with the increases in the deposition pressure. Increasing substrate temperature shifts the UV optical band edge of the films to red. Hydrogen quantity in the ${\alpha}$-Si:H films increases with an increases in the R.F. powr and decreases with an increase in the substrate temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.131-134
• /
• 2001

Vertically aligned carbon nanotubes are grown on iron-deposited silicon oxide substrates by thermal chemical vapor deposition of acetylene gas at the temperature range 750∼950$^{\circ}C$. As the growth temperature increases from 750 to 950$^{\circ}C$, the growth rate increases by 4 times and the average diameter also increases from 30 nm to 130 nm while the density increases progresively with the growth temperature and a higher degree of crystalline perfection can be achieved at 950$^{\circ}C$. This result demonstrates that the growth rate, diameter, density, and crystallinity of carbon nanotubes can be controlled with the growth temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.264-264
• /
• 2010

Single-walled carbon nanotubes (SWCNTs) were grown on a Si wafer by using thermal chemical vapor deposition (t-CVD). We investigated the effect of the catalyst deposition rate on the types of CNTs grown on the substrate. In general, smaller islands of catalyst occur by agglomeration of a catalyst layer upon annealing as the catalyst layer becomes thinner, which results in the growth of CNTs with smaller diameters. For the same thickness of catalyst, a slower deposition rate will cause a more uniformly thin catalyst layer, which will be agglomerated during annealing, producing smaller catalyst islands. Thus, we can expect that the smaller-diameter CNTs will grow on the catalyst deposited with a lower rate even for the same thickness of catalyst. The 0.5-nm-thick Fe served as a catalyst, underneath which Al was coated as a catalyst support as well as a diffusion barrier on the Si substrate. The catalyst layers were. coated by using thermal evaporation. The deposition rates of the Al and Fe layers varied to be 90, 180 sec/nm and 70, 140 sec/nm, respectively. We prepared the four different combinations of the deposition rates of the AI and Fe layers. CNTs were synthesized for 10 min by flowing 60 sccm of Ar and 60 sccm of $H_2$ as a carrier gas and 20 sccm of $C_2H_2$ as a feedstock at 95 torr and $810^{\circ}C$. The substrates were subject to annealing for 20 sec for every case to form small catalyst islands prior to CNT growth. As-grown CNTs were characterized by using field emission scanning electron microscopy, high resolution transmission electron microscopy, Raman spectroscopy, UV-Vis NIR spectroscopy, and atomic force microscopy. The fast deposition of both the Al and Fe layers gave rise to the growth of thin multiwalled CNTs with the height of ${\sim}680\;{\mu}m$ for 10 min while the slow deposition caused the growth of ${\sim}800\;{\mu}m$ high SWCNTs. Several radial breathing mode (RBM) peaks in the Raman spectra were observed at the Raman shifts of $113.3{\sim}281.3\;cm^{-1}$, implying the presence of SWCNTs (or double-walled CNTs) with the tube diameters 2.07~0.83 nm. The Raman spectra of the as-grown SWCNTs showed very low G/D peak intensity ratios, indicating their low defect concentrations.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.7
• /
• pp.106-115
• /
• 2002

Growth characteristics of micro carbon structures fabricated by laser-assisted chemical vapor deposition are studied. Argon ion laser and ethylene were used as the energy source and reaction gas, respectively, to grow micro carbon rod through pyrolytic decomposition of the reaction gas. Experiments were performed at various conditions to investigate the influence of process parameters on growth characteristics such as the diameter or growth rate of the micro carbon rod with respect to reaction gas pressure and incident laser power. Reaction gas pressure in experiments ranges from 200 to 600Torr and the incident laser power from 0.3 to 3.8W. For these conditions, the diameter of the rod increases linearly with respect to the laser power but is almost independent of the reaction gas pressure. Growth rate of the rod changes little with gas pressure when the laser power remains below IW. For a constant reaction gas pressure, the growth rate increase with Increasing laser power, but the rate of increase decreases gradually, implying that the chemical vapor deposition condition changes from a kinetically-limited regime to a mass-transport-limited regime. When the carbon rod was grown at near threshold laser power, a very smooth surface is obtained on the rod. By continuously moving the focusing lens in the direction of growth, a micro carbon rod with a diameter of 287${\mu}{\textrm}{m}$ and aspect ratio of 100 was fabricated..

• Journal of the Korean Society for Heat Treatment
• /
• v.33 no.1
• /
• pp.20-24
• /
• 2020

Single crystal diamonds are in great demand in such fields as mechanical, electronic applications and optoelectronics. Large area single crystal diamonds are attracting attention in future industries for mass production and low cost. In this study, hot filament CVD (HFCVD) is used to grow large area single crystal diamond. However, the growth rate of large area single crystal diamond using HFCVD is known to be very low. The goal of this study is to use single crystal diamond substrates in HFCVD with methane-hydrogen gas mixtures to increase the growth rate of single crystal diamond and to optimize the conditions by analysing the effects of deposition conditions for high quality crystallinity. The deposition pressure, the ratio of CH₄/H₂ gas, the substrate temperature and the distance between the filament and the substrate were optimized. The sample used a 4×4 (mm²) size single crystal diamond substrate (100), the CH₄/H₂ gas ratio was fixed at 5%, the substrate temperature was synthesized to about 1000℃. At this time, the deposition pressure was changed to three types of 50, 75, 85 Torr and deposited. Finally, optimization was investigated under pressure conditions to analyse the growth rate and quality of single crystal diamond.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.05a
• /
• pp.42-45
• /
• 1992

The poly silicon thin films were prepared by solid phase crystallization at 600$^{\circ}C$ of amorphous silicon films deposited on Corning 7059 glass and (100) silicon wafer with thermally grown SiO$_2$substrate by plasma enhanced chemical vapor deposition with varying rf power, deposition temperature, total flow rate. Crystallization time, microstructure, absorption coefficients were investigated by RAMAN, XRD analysis and UV transmittance measurement. Crystallization time of amorphous silicon films was increased with increasing rf power, decreasing deposition temperature and decreasing total flow rate.