• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.2
• /
• pp.49-55
• /
• 2001

ZnO films were fabricated on p-type Si(100) wafer ITO glass and quartz glass by the sol-gel process using zinc acetate dihydrate as starting material. A homogeneous and stable solution was prepared by dissolving the zinc acetate dihydrate in a solution of 2-methoxyethanol and monoethanolamine (MEA). ZnO films were deposited by spin-coating at 2800 rpm for 25 s and were dried on a hot plate at $250^{\circ}C$ for 10 min. Crystallization of the films was carried out at $400^{\circ}C$~$800^{\circ}C$ for 1 h in air. X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM), UV-vis transmittance spectroscopy, FTIR transmittance spectroscopy and Photoluminescence (PL) spectroscopy measurements have been used to study the structural and optical properties of the films. ZnO films highly oriented along the (002)plane were obtained. In all cases the films were found to be transparent (above 70%) in visible range with a sharp absorption edge at wavelengths of about 380nm, which is very close to the intrinsic band-gap of ZnO(3.2 eV). The low temperature band-edge photoluminescence revealed a complicated multi-line structure in terms of bound exciton complexes and the phonon replicas.

• Korean Journal of Ichthyology
• /
• v.13 no.3
• /
• pp.166-172
• /
• 2001

Parental care of eggs of Chromis fumea (Tanaka) was observed by Skin Scuba gear in August 1995 off Cheju Island. The eggs and larval development were observed in the laboratory at Pukyong National University, Pusan. Eggs were deposited on a flat surface of hard substratum and formed a plain sheet of one layer of eggs. Males showed parental care of the eggs by hovering over the nest and attacking other fishes that approached the nest. The spawned eggs were transparent, elliptical in shape and measured 0.73~0.88 mm in long axis and 0.50~0.56 mm in short axis. An analysis by T-test of the long axis of the egg with time showed a significant difference (p<0.01). However, there was no significant difference in short axis with time. Eggs were reared at water temperatures of $23.0{\sim}25.5^{\circ}C$ and took about 4~5 days from embryonic body stage to hatching. The newly hatched larvae were 1.10~1.61 mm in notochord length (NL) had 21 myomeres, has closed mouth but open anus, preanus length was 45.8% of NL. Melanophores were distributed on the occipital region of head, the eye, the peritoneal region, and along the ventral contour. The larvae absorbed the yolk material and oil globule in 3~4 days after hatching and became postlarvae. On the third day after hatching, the larvae had attained 1.9~2.4 mm in NL, had 25 myomeres, and showed rapid growth. By the ninth day after hatching, the larvae had attained 2.9 mm in NL, had an swimbladder in the dorsal margin of ventral region, the preanus length was 37.9% of NL, and their melanophores were enlarged and reduced in number.

• Applied Chemistry for Engineering
• /
• v.8 no.5
• /
• pp.742-748
• /
• 1997

Diamond films which have high hardness and thermal conductivity can be used to improve the performance of WC-Co as a cutting tool material. However, it is difficult to get such coatings of good uniformity and adhesiveness due to the surface characteristics of WC-Co. To get better coatings, some techniques, such as the surface treatment of substrate or the formation of interlayer between substrate and diamond film, have been tried. In the present work, the nickel interlayer is formed onto WC-Co by electroless Ni-P plating, which is introduced as a new method, and then diamond film is deposited on the interlayer. Formation and uniformity of three layers, i.e., substrate, electroless plate, and diamond film, and the adhesiveness of interlayers were studied. To investigate the effects of pretreatment on electroless plating, two different methods such as acid treatment and diamond powder treatment were used. The effects of heat treatment of the electroless plated surface on adhesiveness between the substrate and the interlayer were examined. It was found that as the temperature increases, the Ni crystals grow and then result in improved adhesiveness. Diamond film coatings of pure diamond phase were obtained at $800^{\circ}C$. It is concluded that the heat treated electroless Ni-P plating can be effectively used as a interlayer between WC-Co substrate and diamond film.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.5
• /
• pp.240-246
• /
• 2002

$TiO_2$ films on soda-lime-silica glasses were prepared by spin coating-pyrolysis process using titanium naphthenate as a starting material. As-deposited films were pyrolyzed at $500^{\circ}C$ for 10 min in air and annealed at 500, 550 and $600^{\circ}C$ for 30 min in air. Crystallinity of the film was investigated by X-ray diffraction analysis. A field emission-scanning electron microscope and an atomic force microscope were used for characterizing the surface morphology and the surface roughness of the film. After annealing at 550 and $600^{\circ}C$, the X-ray diffraction patterns consist of only anatase peak. Films annealed at 500 and $550^{\circ}C$ exhibited flat surfaces. While with the increase in annealing temperature to $600^{\circ}C$, the $TiO_2$ film showed abnormal growth of three-dimensional needle-shaped grains. For all samples, high transmittance, above 90 % at 500 nm, was obtained at visible range. To investigate photocatalytic properties, IR absorbance associated with the C-H stretching vibrations of a thin solution-cast film of stearic acid under 365 nm (2.4 mW/$\textrm{cm}^2$) UV irradiation was estimated.

• Korean Journal of Materials Research
• /
• v.9 no.1
• /
• pp.14-17
• /
• 1999

Tin oxide films as an anode layer for microbatteries were deposited by using rf magnetron sputtering. Characterization of the films was carried out in terms of working pressure in the range of 5~30 mtorr. Rf power and substrate temperature during deposition were fixed at 2.5W/$\textrm{cm}^2$ and A.T., respectively. The crystal orientation of $SnO_2$films was changed from (110) to (101) or (211) with the increasing working pressure. Refractive index and film density of the films also decreased with the increasing working pressure. The $SnO_2$ thin film formed under optimum conditions was found to have a reversible capacity of 446.9$\mu$Ah/$\textrm{cm}^2$-$\mu\textrm{m}$ and good reversibility when the working pressure was fixed at 10mtorr. As the working pressure decreased, film density increased. It was thought that the capacity of $SnO_2$films increased due to the increase in the amount of active materials which can react with Li electrochemically. Furthermore, cycle characteristics of the anode material was also influenced by film stress.

• Journal of Chest Surgery
• /
• v.32 no.11
• /
• pp.998-1003
• /
• 1999

Background: Bovine pericardium treated with glutaraldehyde(GA) is one of the most popular prosthetic materials. However, its late calcific degeneration after implantation results in early failure of the prosthesis. Therefore, we investigated the effects of combined treatment with sodium dodecyl sulfate(SDS) and glutamate on calcific degeneration of GA treated bovine pericardium. Material and Method: Sixty square-shaped pieces of bovine pericardia were fixed in 0.625% GA solution with 4g/L MgCl2.6H2O as a control group (group 1). Sixty pieces pretreated with 1% SDS (group 2) and sixty pieces posttreated with 8% glutamate (group 3) were also fixed in the same GA solution. Sixty pieces pretreated with 1% SDS and posttrated with 8% glutamate were also fixed in the same GA solution (group 4). After 1 month of fixation, the pieces were implanted into the belly of sixty Sprague-Dawley rat subdermally and were extracted 1 month, 2 months and 3 months after the implantation. With an atomic absorption spectrophotometry, we measured the calcium amount deposited. Result: The calcium deposition in 1 month was 2.01$\pm$0.13 mg/g in group 1, 1.45$\pm$0.31 mg/g in group 2, 2.49$\pm$0.15 mg/g in group 3 and 0.75$\pm$0.27 mg/g in group 4. In 2 months, it was 3.57$\pm$0.15 mg/g in group 1, 0.98$\pm$0.30 mg/g in group 2, 3.46$\pm$0.12 mg/g in group 3, and 1.48$\pm$0.39 mg/g in group 4, and 5.45$\pm$0.42 mg/g in group 1, 2.43$\pm$0.53 mg/g in group 2, 4.20$\pm$0.55 mg/g in group 3, and 1.02$\pm$0.27 mg/g in group 4 in 3 months. The calcium depositions in group 2 and 4 were less than those of group 1 and 3 in 1 month 2, months, and 3 months(p<0.01). The calcium depositions in group 1, 2 and 3 increased with time. However, they remained unchanged in group 4, which was statistically significant(p<0.01). Conclusion: Pretreatment with SDS is effective in reducing calcification of GA treated bovine pericardium, and the combined method of pretreatment with SDS and posttreatment with glutamate was more effective than the other methods.

• Journal of Chest Surgery
• /
• v.32 no.11
• /
• pp.989-997
• /
• 1999

Background: Calcific degeneration is the major cause of clinical failure of glutaraldehyde (GA) crosslinked bioprosthetic tissues implanted in the body and necessitates the reoperation or causes death. Surface modification of biologic tissues using sulfonated polyethyleneoixde (PEO-SO3) has been suggested to significantly enhance blood compatibility, biostability and calcification-resistance by means of the synergistic effect of highly mobile and hydrophilic PEO chains and electrical repulsion of negatively charged sulfonate groups. This study was designed to evaluate the anticalcification effect of surface-modification of biologic arteries by direct coupling of PEO-SO3 after GA fixation and changes of calcification according to the implantation period through the quantitative investigation of the deposited calcium and phosphorous contents of the biologic arterial tissues in the canine circulatory implantation model. Material and Method: Total of 16 fresh canine carotid arteries were harvested from eight adult dogs and divided in to GA group(n =8) and PEO-SO3 group(n=8). Sulfonation of diamino-terminated PEO was performed using propane sultone. Canine carotid arteries were only crosslinked with 0.65% GA solution in GA group and modified by direct coupling 5% PEO-SO3 solution after GA crosslinkage for 2 days and stabilized by NaBH4 solution for 16 hours in PEO-SO3 group. In both groups the resected segment of bilateral carotid arteries were reconstructed. Reconstructed segments of the two groups were analysed the quantities of calcium and phosphorous contents after 3(n=4) and 6(n=4) weeks in vivo. Result: After implantation of 3 seeks, PEO-SO3 group showed significantly less depositions.

• Journal of the Korean Vacuum Society
• /
• v.21 no.3
• /
• pp.136-141
• /
• 2012

We report investigation of structural and optical characteristics of $In_2Se_3$ thin films fabricated by thermal annealing process. Indium (In) is deposited on substrates by sputtering methods and $In_2Se_3$ thin films are fabricated by thermal annealing it with selenium vapor. The annealing temperature was changed from $150^{\circ}C$ to $400^{\circ}C$. We observe formation and phase changes of $In_2Se_3$ thin films with increase of annealing temperature. Conglomeration of In is observed at low annealing temperature (${\leq}150^{\circ}C$). $In_2Se_3$ phases are started to form at $200^{\circ}C$ and ${\gamma}-In_2Se_3$ phase form at $350^{\circ}C$. High-quality ${\gamma}-In_2Se_3$ thin film with wurtzite structure is obtained at $400^{\circ}C$ of annealing temperature. Furthermore, we confirm that band gaps of $In_2Se_3$ thin films are increased according to increase of annealing temperature. Optical band gap of high-quality ${\gamma}-In_2Se_3$ is found to be 1.796eV.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.642-642
• /
• 2013

Graphene, two dimensional single layer of carbon atoms, has tremendous attention due to its superior property such as high electron mobility, high thermal conductivity and optical transparency. Especially, chemical vapor deposition (CVD) grown graphene has been used as a promising material for high quality and large-scale graphene film. Unfortunately, although CVD-grown graphene has strong advantages, application of the CVD-grown graphene is limited due to ineffective transfer process that delivers the graphene onto a desired substrate by using polymer support layer such as PMMA(polymethyl methacrylate). The transferred CVD-grown graphene has serious drawback due to remaining polymeric residues generated during transfer process, which induces the poor physical and electrical characteristics by a p-doping effect and impurity scattering. To solve such issue incurred during polymer transfer process of CVD-grown graphene, various approaches including thermal annealing, chemical cleaning, mechanical cleaning have been tried but were not successful in getting rid of polymeric residues. On the other hand, lithographical patterning of graphene is an essential step in any form of microelectronic processing and most of conventional lithographic techniques employ photoresist for the definition of graphene patterns on substrates. But, application of photoresist is undesirable because of the presence of residual polymers that contaminate the graphene surface consistent with the effects generated during transfer process. Therefore, in order to fully utilize the excellent properties of CVD-grown graphene, new approach of transfer and patterning techniques which can avoid polymeric residue problem needs to be developed. In this work, we carried out transfer and patterning process simultaneously with no polymeric residue by using a metal etch mask. The patterned thin gold layer was deposited on CVD-grown graphene instead of photoresists in order to make much cleaner and smoother surface and then transferred onto a desired substrate with PMMA, which does not directly contact with graphene surface. We compare the surface properties and patterning morphology of graphene by scanning electron microscopy (SEM), atomic force microscopy(AFM) and Raman spectroscopy. Comparison with the effect of residual polymer and metal on performance of graphene FET will be discussed.

• Journal of Korean Ophthalmic Optics Society
• /
• v.18 no.2
• /
• pp.107-115
• /
• 2013

Purpose: This study was conducted to investigate the change of soft contact lens parameters after eyeliner deposition and compare the cleaning efficiency and the recovery rate of lens parameters by different cleaning methods. Methods: The eyeliner was deposited on three types of soft contact lenses made of different materials for 1 hour, 4 hours and 6 hours and those lenses were washed by the eyeglasses ultrasonic cleaning and by hands. The changes in visible light transmittance, diameter and surface of those lenses were compared before and after cleaning of the lens. Results: The visible light transmittance of soft contact lenses decreased along with the deposition time of eyeliner. The patterns of the eyeliner deposition on soft contact lens appeared differently depending on the physical properties of the lens material. Thus, the largest eyeliner deposition was found on narafilcon A lens. The diameters of hilafilcon B and etafilcon A lenses were decreased, however, the diameter of narafilcon A lens was increased. The cleaning efficiency of the eyeliner deposition was greater with the multipurpose solution by hands than with the eyeglasses ultrasonic cleaner. However, the recovery of lens parameters such as the lens diameter, visible light transmittance and lens surface due to the eyeliner deposition to its original state was limited. Conclusions: From these results, it is suggested to minimize eye makeup when wearing soft contact lens. Furthermore, the reduced wearing time and shorter cycle of lens replacement may be needed by considering a change of lens parameter when the repeat eye makeup is applied.