• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.1142-1150
• /
• 2010

An elementary particle of bottom ash is similar to fine sand. So which expected from replace expensive sand. Therefore, this study conducts cyclic triaxial test and a resonant test using relative density, which is obtained from a relative density test of bottom ash and standard sand. Also, it compares antiseismic characteristics of bottom ash and standard sand in order to analyze the possibility of commercial use as a construction material.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.59-62
• /
• 2000

As the density of memories increases, unwanted interference between cells and coupling noise between bit-lines are increased and testing high density memories for a high degree of fault coverage can require either a relatively large number of test vectors or a significant amount of additional test circuitry. From now on, conventional test algorithms have focused on faults between neighborhood cells, not neighborhood bit-lines. In this paper, a new algorithm for NPSFs, and neighborhood bit-line sensitive faults (NBLSFs) based on the NPSFs are proposed. Instead of the conventional five-cell and nine-cell physical neighborhood layouts to test memory cells, a three-cell layout which is minimum size for NBLSFs detection is used. To consider faults by maximum coupling noise by neighborhood bit-lines, we added refresh operation after write operation in the test procedure(i.e., write \longrightarrow refresh \longrightarrow read). Also, we present properties of the algorithm, such as its capability to detect stuck-at faults, transition faults, conventional pattern sensitive faults, and neighborhood bit-line sensitive faults.

• Journal of the Korean Society of Safety
• /
• v.33 no.4
• /
• pp.15-20
• /
• 2018

In this study, we have performed the Cone Calorimeter test and Smoke density test in accordance with ISO 5660-1 and ASTM E662 respectively to check the smoke production characteristics of rubber flooring materials for railway vehicle. Early in the ASTM E662 test, more smoke was produced in the flame mode test than non-flame mode test, but later more smoke was produced in non-flame mode test. The correlation($R^2$) between TSR(Total Smoke Release) by ISO 5660-1 and Ds(Specific Optical Density) by ASTM E662 Flame mode was 0.782. The $R^2$ between TSR by ISO 5660-1 and Ds by ASTM E662 Non-flame was 0.930.

• Journal of the Korean Geosynthetics Society
• /
• v.14 no.4
• /
• pp.45-58
• /
• 2015

Even though the plate bearing test (PBT) to evaluate the load baring capacity and the field density test to evaluate the relative density are mainly used for quality control of soil compaction in Korea, use of the dynamic cone penetrometer test (DCPT) and the dynamic plate bearing test (DPBT) considering economic feasibility, rapidity, and suitability for field conditions increase to use for quality control of soil compaction. In this study, bearing capacity and relative density of subgrade with thickness of 20 cm, 30 cm, and 40 cm are estimated using PBT, DCPT, DPBT and field density test in three field compaction tests, and the relationship among various compaction evaluation methods is analyzed and discussed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.2
• /
• pp.183-188
• /
• 1996

The compressive stress-strain response of Low Density Polyurethane foam material is modeled using the finite element method. A constitutive equation which include experimental constants based on quasi-static and dynamic uniaxial compression test is proposed. Impact test with different impactor masses and velocities are performed to verify the proposed model. The comparison between impact test and finite element analysis shows good agreements.

• Communications for Statistical Applications and Methods
• /
• v.2 no.1
• /
• pp.122-136
• /
• 1995

The objective of this research is to investigate the problem of goodness-of-fit testing based on nonparametric density estimation with a data-driven smoothing parameter. The small and large sample properties of a new test statistic $\hat{\lambda_a}$ is investigated. The test statistic $\hat{\lambda_a}$ is itself a smoothing parameter which is selected to minimize an estimated MISE for a truncated series estimator of the comparison density function. Therefore, this test statistic leads immediately to a point estimate of the density function th the event that $H_0$ is rejected. The limiting distribution of $\hat{\lambda_a}$ is obtained under the null hypothesis. It is also shown that this test is consistent against fixed alternatives.

• Journal of muscle and joint health
• /
• v.18 no.1
• /
• pp.73-82
• /
• 2011

Purpose: The purpose of this study was to investigate the effects of a 12-week Tai Chi on the bone mineral density and bone metabolic markers in postmenopausal women Methods: Data were collected from March to July, 2009. Fifty postmenopausal women were recruited for the study. Twenty two women were allocated to experimental group, and 28 to control group. The experimental group underwent Tai Chi exercise twice a week for twelve weeks. The control group was only notified with results of bone mineral density and bone metabolic markers. Bone mineral density was measured by using of DTX-200 (Osteometer MediTech, Hawthorne, CA, USA) at distal radius site and bone metabolic markers were measured by radioimmunoassay method. Collected data were analyzed by t-test, $X^2$-test, and Mann-Whitney test. Results: After 12 weeks of treatment, the Tai Chi group showed a significant difference in bone mineral density compared to control group but no significant effect on osteocalcin and deoxypyridinoline level. Conclusion: Our results suggest that 12 weeks of Tai chi may delay bone loss in postmenopausal women.

• Fire Science and Engineering
• /
• v.20 no.4 s.64
• /
• pp.26-32
• /
• 2006

Nowadays in Korea, KS F 2271 has been using for the test of fire safety performance of sandwich panels. Smoke toxicity test is the test for the toxicity evaluation of smoke and hazardous gas, caused by combustion of building materials and finishing materials. Smoke toxicity can be evaluated by the mean incapacitation time of mice; however this method is not a quantitative way. This test result can be influenced by the health status of mice and test condition. Specific optical density can be quantitatively measured by ISO 5659-2 single chamber method and toxic gases can be quantitatively measured by FTIR analysis. In this study, specific optical density of sandwich panel insulations, which are widely used in Korea, were tested using the ISO 5659-2 single chamber test method and compared with each test. Also, in the second test of three tests for each specimen, FTIR analysis was performed and quantitative test results(HCl, $NO_2$, etc) were compared with each test result.

• International Journal of Highway Engineering
• /
• v.17 no.1
• /
• pp.51-58
• /
• 2015

PURPOSES : The objective of this study is to compare the densities of asphalt pavements measured both in the field and in the laboratory, and also to evaluate the applicability of field density measuring equipment, such as the pavement quality indicator (PQI), by using statistical analysis. METHODS : For the statistical analysis of the density measured from asphalt pavement, student t-tests and a coefficient of correlation are investigated. In order to compare the measured densities, two test sections are prepared, with a base layer and an intermediate layer constructed. Each test section consists of 9 smaller sections. During construction, the field densities are measured for both layers (base and intermediate) in each section. Core samples are extracted from similar regions in each section, and moved to the laboratory for density measurements. All the measured densities from both the field and laboratory observations are analyzed using the selected statistical analysis methods. RESULTS AND CONCLUSION : Based on an analysis of measured densities, analysis using a correlation coefficient is found to be more accurate than analysis using a student t-test. The correlation coefficient (R) between the field density and the core density is found to be very low with a confidence interval less than 0.5. This may be the result of inappropriate calibration of the measuring equipment. Additionally, the correlation coefficient for the base layer is higher than for the intermediate layer. Finally, we observe that prior to using the density measuring equipment in the field, a calibration process should be performed to ensure the reliability of measured field densities.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.5
• /
• pp.203-210
• /
• 2003

This paper describes high voltage and high energy density capacitor developed for pulsed power applications. The rated voltage of the developed capacitor is DC 22 [kV], the capacitance is 206 [$\mu$F] and the energy density is about 0.7 [kJ/kg]. Polypropylene film and kraft paper were used as the dielectrics. The ratio of the thickness of each dielectric material which consists of the composite dielectric structure, stacking factor and the termination method were determined by the charging and discharging tests on model capacitors. In terms of energy density, the developed capacitor has higher energy density compared with the products of foreign leading companies. In addition, it has been proved that the life expectancy can be more over 2000 shots through the charging and discharging test. The voltage reversal factor was 20%. This capacitor can be used as numerous discharge applications such as military, medical, industrial fields.