• 한국농공학회지
• /
• 제34권3호
• /
• pp.33-42
• /
• 1992

The shear strength of cohesionless Soils results from particle-to-particle friction and structural resistance by interlocking. And, the shear strength of soils is subjected to vary depending on the internal states and external condtions. If the volume change occurring in the soils and stress-strain relationships under the internal and external changes can accrurately he described, it is possible to predict the behaviors of soils. To accomplish these objectives a series of drained triaxial compression tests and isotropic compression test was performed on the Banwol sand at different relative densities ranging from 20% to 80% and different confining pressures ranging from 0.4kgf/cm$^2$ to l2kgf/cm$^2$. The results and main conclusions of the study are summarized as follows; 1.When the relative density or the confining pressure is increased, the maximum deviator stress is increased. The ratio of the maximum deviator stress and the confining pressure is linearly proportional to the relative density. 2.It is observed that the dilatancy depends not only upon its relative density but also the confining stress, and that the maximum deviator stress is obtained after the diatancy occurs. 3.The volume of sands undergoes initial contraction prior to the dilatancy occurred by strain softening. The dilatancy rate eventually approaches the critical state or a constant volume. 4.At lower strains, Poisson's ratio approaches a certain minimum value regadless of the state of materials. At larger strains, however, the ratio is increased as the relative density is increased. 5.It is observed that the modulus of elasticity is linearly proportional to the relative density and the pressure. 6.When the relative density is increased, the friction angle of sands is linearly increased. 7.When the relative density is increased, the expansion index and the compression index are linearly decreased, and the ratio of the two is about 1/3.

• 한국세라믹학회지
• /
• 제39권11호
• /
• pp.1083-1089
• /
• 2002

알루미나 세라믹스에 MgO와 $TiO_2$를 각각 단독으로 첨가했을 때의 치밀화와 소결 거동을 수축률-소결 밀도 관계를 통해 비교 조사하였다. MgO가 첨가되었을 때는 소결 전과정을 통해 입성장은 억제되고 치밀화는 촉진되었으나, $TiO_2$가 첨가되었을 때는 입성장은 촉진된 반면 치밀화는 떨어졌다. 또한 입자 크기, 밀도, 수축률등을 통해 수축률-소결 밀도 관계를 구하여 최대 수축률을 나타내는 밀도값(Density of Maximum Shrinkage Rate:${\rho}$J.S.R)을 조사해 보았다. 이때 최대 수축률을 나타내는 밀도값보다 낮은 밀도를 보이는 영역에서는 치밀화가 입성장보다 우세하게 진행되었으며 최대 수축률을 나타내는 밀도값보다 높은 밀도의 영역에서는 입성장이 보다 우세하게 진행되는 것으로 추정하였다. 이때 최대 수축률을 나타내는 밀도값은 $TiO_2$가 첨가된 알루미나 < 순수 알루미나 < MgO가 첨가된 알루미나의 순서로 높은 값을 보였다.

• KSBB Journal
• /
• 제13권4호
• /
• pp.411-417
• /
• 1998

The possibility of application of membrane type immobilized adsorbent to the fed-batch or perfusion culture system with anchorage-independent cells as well as batch system was investigated. The improvement in cell density and cell viability due to the combination of immobilized adsorbent with each culture system was evaluated for the investigation, and the optimum culture system employing immobilized adsorbent system was suggested based on the results. It was observed that the system with immobilized adsorbent showed better cell growth and cell viability than that without immobilized adsorbent in every operation system of batch, fed-batch, and perfusion. In case of batch system, 200% improvement of maximum cell density was observed in the system where ammonium chloride was added on purpose. And 50% improvement of maximum cell density was observed in the fed-batch system where ammonium ion accumulates significantly, while small increase in maximum cell density was observed in the perfusion system where dilution of waste byproducts exists. Especially, the fed-batch system showed the most significant improvement on cell growth because both compensation of nutrient and removal of ammonium ion occurred simultaneously in the system. Therefore a combined system of immobilized adsorbent and fed-batch operation could be suggested as an optimum system with in situ removal of ammonium ion.

• 열처리공학회지
• /
• 제16권6호
• /
• pp.311-314
• /
• 2003

In Mo-Xwt%Cu compound, Physical and thermal properties were systematically evaluated in terms of Cu contents and sintering temperature. Typically Cu contents were varied from 15 to 25wt% and also the Sintering temperatures were changed from $1115^{\circ}C$ to $1350^{\circ}C$. In physical properties, Mo-15~25wt%Cu has the maximum density of 95% while Mo-20wt%Cu has the maximum thermal conductivity of 165.179[${\mu}/m^{\circ}C$] at sintering temperature of $1300^{\circ}C$. Especially, Mo-25wt%Cu has the maximum hardness of 173.4 at sintering temperature of $1150^{\circ}C$ and the maximum thermal expansion of 9.0[W/mK] as the specimen heated in the range of temperature from $50^{\circ}C$ to $400^{\circ}C$. Based on electrical conductivity measurements, the relative density increased within creasing Cu contents and the values were in the range of 100~150[W/mK].

• 한국군사과학기술학회지
• /
• 제14권2호
• /
• pp.205-212
• /
• 2011

In this paper, we have proposed a method for quantization of the stratification strength in the sea water and analysing the distributions of the maximum stratification depths calculated by the method at the seas near the Korean peninsular. For calculating the stratification strength, modified and applied the potential energy anomaly formular which was suggested by Simpson in 1977. The data had been collected by NFRDI from 1971 to 2008 were used to determine the maximum vertical density gradient depth and the relative potential energy anomaly at that depth. In the East Sea, the stratification depth has become deepened about 20m in February and April since 1971. In Yellow-South Sea, the maximum density gradient depth has been deepened about 10m only in December during the same period and the difference of the stratification depth between summer and winter has been enlarged. These trends of variation of stratification strength and depth near the Korean peninsular should be investigated more carefully and continuously. And the results of these studies could be adopted for the more efficient operation of underwater weapon and detection systems.

• Journal of Magnetics
• /
• 제15권2호
• /
• pp.74-77
• /
• 2010

This paper deals with optimum design criteria for maximum torque density & minimum torque ripple of a Flux Switching Motor (FSM) using response surface methodology (RSM) & finite element method (FEM). The focus of this paper is to find a design solution through the comparison of torque density and torque ripple which vary with rotor shape. And then, a central composite design (CCD) mixed resolution was introduced and analysis of variance (ANOVA) was conducted to determine the significance of the fitted regression model. The proposed procedure allows one to define the rotor dimensions, starting from an existing motor or a preliminary design.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1990년도 하계학술대회 논문집
• /
• pp.231-235
• /
• 1990

Soft magnetic silicon steels containing up to 6.5wt% of silicon were prepared by powder metallurgical processing and their magnetic properties were evaluated. The magnetic properties of P/M silicon steels are similarly affected by the silicon addition as those of conventional ingot processed ones but are also significantly affected by density and interstitial impurities particularly oxygen content. Magnetic flux density, $B_{10}$ and coercivity, Hc, tends to decrease with silicon content whereas maximum permeability, ${\mu}m$, decreases first and then increases rapidly above 5 wt% silicon. Increasing density also increases magnetic flux density and maximum permeability but reduces coereivity. The latter two properties are, however, affected more strongly with oxygen content.

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 2008년도 춘계학술논문발표회 논문집
• /
• pp.273-276
• /
• 2008

As the rapid and various changing of social aspects, the structures are getting bigger, higher and more complex. The importance of evacuation is on the rise as increased using frequency of multiplex sale facility and it's high population density. According to the result of a survey with 4 domestic wholesales mart's population density, the average and maximum was 0.41(人/$m^2$) and 0.46(人/$m^2$). considering evacuation dangerousness, the maximum value will be suitable for computation of evacuation capacity and this will be submitted as a basic data for computation of evacuation capacity.

• 한국초전도ㆍ저온공학회논문지
• /
• 제1권1호
• /
• pp.22-27
• /
• 1999

Recently, small-sized superconducting magnetic storage($\mu$SMES) coils become commercially as an energy storage device for a power conditioner. In design and fabrication of the $\mu$SMES coils, to determine optimum current capacity of the superconducting(SC) conductors is one of the important things. We thus investigated the effect of conductor's current capacity, current density, and stability on the coil's maximum stored energy density in consideration of AC losses and switching device's capacities in a power converter. The results show that the smaller current capacity of the SC conductors is preferred for the $\mu$SMES coils but can increase their induced voltage excessively.

• 산업기술연구
• /
• 제7권
• /
• pp.9-14
• /
• 1987

The maximum specific gravity of asphaltic concrete can be calculated based on the effective specific gravity of aggregates and the specific gravity of asphalt cement. The maximum specific gravity is sometimes obtained based on the apparent specific gravity of aggregates and specific gravity of asphalt concrete. However, the apparent specific gravity is in general greater than the effective specific gravity for most aggregates. This study showed, by comparing the results obtained based on two specific gravities, that application of the apparent specific gravity instead of the effective specific gravity resulted in discrepancies in the calculated values of effective asphalt content, air void and maximum density.