• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.229-232
• /
• 1997

A free space transmission method using standard gain horn antennas in the frequency range from 9.0 to 10.5GHz is applied to determine the dielectric properties of grain such as rough rice, brown rife and barley. The dielectric constant and loss factor, which depend on the moisture content of the wetted grain are obtained from the measured attenuation and phase shift by vector network analyzer. The effect of density fluctuation, which is an important parameter governing the dielectric properties of grain, on the dielectric constant and loss factor is presented. A new density-independent model in terms of measured attenuation and moisture density is proposed for reducing the effects of density fluctuation on the moisture content measurement.

• Proceedings of the Korean Fiber Society Conference
• /
• 1988.06a
• /
• pp.35-37
• /
• 1988

This paper shows the possibility of the application of the orientation density function of fibers to the mechanics of fibrous assembly. As an example, the orientation density function of a single yarn was theoretically derived in consideration of the idealized helical yarn. And the theoretical derivation of the tensile modulus of the fibrous assembly was performed in view of the fiber orientation. Application of this orientation density function to the obtained tensile modulus and to the contraction factor of the yarn was also performed so that the theoretical equations of the tensile modulus and the contraction factor of the yarn were obtained. Close agreement was shown between the theoretical and the existing equations. Consequently it was confirmed that the application of the orientation density function to the mechanics of the fibrous assembly is sufficiently possible.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.2 s.115
• /
• pp.16-21
• /
• 2006

Uneven ink transfer of a print can be traced to several causes such as an incomplete contact between the paper surface and ink film, a coarse pattern of a continuous ink film after transfer, uneven absorption, etc. Uneven ink transfer was studied in this points by the Tollenaar. Uneven distributions of printed density are reflected in low ${\ulcorner}m{\lrcorner}$ values of the print. Tollenaar's smoothness coefficient ${\ulcorner}m{\lrcorner}$ value was important factor that deciding printed quality which was easily obtain by densitometry. Limiting print density $D_{\infty}$ that obtained Tollenaar's formulation working as a influence factor at the printed quality. In this study, we obtained limiting print density $D_{\infty}$ and smoothness coefficient ${\ulcorner}m{\lrcorner}$ value of domestic newspapers and foreign newspapers. And we analyzed about properties of the newspaper. The result of this study, smoothness coefficient ${\ulcorner}m{\lrcorner}$ value and limiting print density $D_{\infty}$ showed the good results in the low porosity and low roughness newspaper. Datum which obtained by this study was used as printability factor for the quality control and improvement of domestic newspaper and wished to apply as a basic data for the domestic newspaper quality.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.2
• /
• pp.39-52
• /
• 2003

This paper deals with an automatic design procedure for the maximum torque density and power factor in a synchronous reluctance motor (SynRM). The focus of this paper is the design relative to the number of flux barrier and the ratio Kw of flux barrier width to iron sheet width of a SynRM under the mechanical constraint. The Finite Elements Analysis (FEA) has been used to evaluate the maximum torque density and power factor with each rotor shape. The proposed procedure allows to define the rotor geometric dimensions starling from an existing mootor or a preliminary design. The maximum torque density and power factor of a SynRM has been resulted with the rotor design variation. To prove the propriety of the designed SynRM, the Digital Signal Processor (DSP) installed experimental devices are equipped and the efficiency characteristic test is Performed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.946-949
• /
• 2005

In this paper, influence factors on dynamic properties of floor impact noise insulation materials are suggested. For this purpose measurements on the dynamic stiffness and the loss factor of resilient materials are carried out by Korea standard (KS F 2868) according to the change of density, thickness, design pattern, and composition of materials. As a result the values of dynamic stiffness was decreased at high density and thick thickness, and that of loss factor was increased at low density. For dynamic properties, the pattern of lattice and waffle type material is better than that of plat type, and the mixed composition of materials is better than the composition of double layer materials at same thickness.

• The Korean Journal of Ceramics
• /
• v.2 no.1
• /
• pp.11-18
• /
• 1996

The variation of electrical conductively and Seebeck coefficient of FeSi2 according to the density of the specimen has been observed over the temperature range 50 to $700^{\circ}C$. A conventional pressureless sintering method with various sintering time (0, 0.5, 1, 5h) at $1190^{\circ}C$ and/or various sintering temperatures(1160, 1175, 1190, $1200^{\circ}C$) for 2 h was carried out to prepare $FeSi_2$ specimens having various densities. The relationship between the electrical conductivity and Seebeck coefficient was investigated after two steps of annealing (at $865^{\circ}C$ and then $800^{\circ}C$ for total 160h) and thermoelectric measurement. The electrical conductivity for the specimens showed a typical tendency of semiconductor, the average activation energy of which in the intrinsic region (above $300^{\circ}C$) was observed approximately as 0.452 eV, and increased slightly with density. On the other hand, the specimen of the lower density showed the higher value of Seebeck coefficient in the intrinsic region. As the temperature fell into the non-degenerate region, the highly densified specimen which had relatively little residual metal phase showed the higher value of Seeback coefficient. The power factor of all specimens showed the optimum value at $200^{\circ}C$. However, the power factor of the specimen of the lower density increased again from $400^{\circ}C$ and that of the higher dense specimen increased from $500^{\circ}C$. The power factor was more affected by Seebeck coefficient than electrical conductivity over all temperature range.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.4
• /
• pp.369-376
• /
• 2002

The dielectric properties of cereal grains such as short-grain rough rice, brown rice and barley with various moisture contents were determined by measuring the attenuation and phase shift of the microwave signal trough the grain samples at 9.5GHz. The microwave free-space transmission measurement system consisted of sample holder, horn antenna and network analyzer. Dielectric constant and loss factor of grain samples increased with moisture content and bulk density and agreed well with previous research results. Moisture density, which is defined as the product of moisture content and bulk density, was proposed as a bulk density and variety compensation factor. The technique for measurement of dielectric properties based on free-space transmission may be useful for other particulate materials.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.4
• /
• pp.367-371
• /
• 2003

In order to determine the effective way of measuring the Mode I stress intensity factor for a material containing a two-dimensional surface crack by means of the alternating current potential drop(ACPD) technique, the change in magnetic flux density between crack surfaces and above the specimen surface due to load was studied theoretically. The magnetic flux density in the air between crack surfaces is uniform and above the specimen surface is not changed by increasing the load in the material. Therefore, the change in potential drop due to load in a measuring system which was designed to induce a large amount of electro-motive force was caused by the change in internal inductance of material, the change in the mutual inductance between internal inductance of material and measuring system and the change in the mutual inductance between internal inductance of material and power supply line.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.74-78
• /
• 2003

This paper shows the dosimetric uncertainties of electromagnetic field at in-vivo and in-vitro experiments. For more accurate consequences of these researches, we have tried to find out any correlations among output power, power density and specific absorption rate(SAR) with the results of in-vivo, in-vitro tests and SAR reports of cellular phone and PDA. In the case of in-vivo tests, the power density has close statistical correlations with SAR value and in the event of in-vitro tests, the output power has considerable statistical correlations with SAR containing duty factor. On the other hand, we found that both power density and output power don't have any close correlations with SAR. And, we obtained fitted regression form among frequency, power density and SAR containing duty factor through multiple linear regression analysis.

• Journal of the Korean Geosynthetics Society
• /
• v.15 no.2
• /
• pp.13-24
• /
• 2016

The safety factor of an infinite slope tends to be analyzed as lower when the effects of root cohesion are not considered into the equation. Thus, it is essential to consider regional characteristics such as root cohesion and crown density in order to obtain a reasonable safety factor value. In this study, The safety factor of the landslide model, both before and after considering crown density and root cohesion, was calculated and a comparative analysis was carried out. The safety factor is increased by the effect of roots cohesion of the analysis results, the amount of increase in safety factor along the inclination of the slope angle has been analyzed with various things, the effect of reinforcing the roots cohesion, slope of the lower angle it was found that the higher the safety factor increase.