• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.12 no.1
• /
• pp.11-17
• /
• 1999

Aging characteristics of the crosslinked polyethylene have been measured after applying electrical, thermal and combined stresses. ICP and FT-IR measurements confirmed diffusion of low molecular weight components such as antioxidant and presence of carbonyl group. Carbonyl group of aged crosslinked polyethylene under combined stress was detected by FT-IR. As deterioration of the crosslinked polyethylene progresses, crystallinity degree and density decrease. Also, dielectric properties have been measured by tan $\delta$ and $\varepsilon$$_{r}$ measurements. The three-parameter Weibull distribution was found to be the best suited among other probabilistic distribution representing the dielectric breakdown strength of aged crosslinked polyethylene. The scale parameter and location parameter decreases as the applied stress increases. The shape parameter increases as the stress increases.s.

• Kyungpook Mathematical Journal
• /
• v.50 no.2
• /
• pp.307-314
• /
• 2010

By introducing a homogeneous kernel of 0-degree with an independent parameter and estimating the weight coefficient, a bilateral form of the Hilbert-type series inequality with a best constant factor is established.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.30 no.4
• /
• pp.320-328
• /
• 1994

In 1980 s to 1990 s the marine propulsion diesel engines have been developed into lower speed and longer stroke for the enegy saving (small S.F.O.C). As these new trends the conventional mechanical-hydraulic governors were not adapted to the new requirements and the digital governors have been adopted in the marine use. The digital governors usually use the control algorithms such as the PID control, optimal control, adaptive control and etc. While the engine has delay time and parameter variations these control algorithms have difficulty in considering the stability and the robustness for the model uncertainty. In this study, the $H_{\infty}$ controller design method are applied in order to design the feedback controller K(s) to the speed control of the low speed marine diesel engine, and the two-degree-of-freedom control system is constituted with $H_{\infty}$controller. By comparison of responses of the two-degree-of-freedom control system under the delay time and parameter variations is confirmed.

• Korean Journal of Optics and Photonics
• /
• v.27 no.6
• /
• pp.223-228
• /
• 2016

The birefringence of distributed, uniaxially anisotropic molecules like liquid crystals is calculated as the degree of ordering is varied. The relation between the normalized birefringence ${\Delta}n_{rel}$ and the orientational order parameter S is investigated. The distribution function, which enables one to monitor the degree of ordering of liquid crystals including randomly distributed ones, is introduced. Using this distribution function, a series of distributed liquid crystals with order parameters ranging from 0 to 1 are generated, and ${\Delta}n_{rel}$ and S of the correspondingly distributed liquid crystals are calculated. Based on the calculated data, it is revealed that ${\Delta}n_{rel}$ and S satisfy the quasi-linear relation of $S=(1+a){\Delta}n_{rel}-a{\Delta}n^2_{rel}$, where a can be approximated as $n_o{\frac{{\Delta}n}{4}}$. The anisotropy of molecular polarizability is also calculated, using the birefringence, and separately following Vuks' method and Neugebauer's method, and it is shown that the relations between S and the molecular-polarizability anisotropy are also quasi-linear.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.1
• /
• pp.43-53
• /
• 1997

A robust stability condition for linear systems with time delay in all variables and parameter uncertainties in all system matrices is derived. Robust performance condition that accounts for robust model-matching of closed loop system and disturbance rejection is also derived. Using the robust performance condition, robust $H^{\infty}$ controller and .mu.(sgructured singular value) controller with two-degree-of-freedom(2DOF) are designed. The controller structure is considered for $H^{\infty}$ controller, while uncertainity structure is considered for .mu. controller. Using the proposed method, $H^{\infty}$ and .mu. controllers for underwater vehicle with time delay and parameter variations are designed. Simulations of a design example with hydrodynamic parameter variations and disturbance are presented to demonstrate the achievement of good robust performance.ce.

• Bulletin of the Korean Mathematical Society
• /
• v.32 no.2
• /
• pp.271-279
• /
• 1995

In 1986, Fabry, Mawhin and Nkashama [1] have considered periodic solutios for Lienard equation $$ (1_s) x" + f(x)x' + g(t,x) = s, $$ where s is a real parameter, f and g are continuous functions, and g is $2\pi$-periodic in t and have proved that if $$ (H) lim_{$\mid$x$\mid$\to\infty} g(t,x) = \infty uniformly in t \in [0,2\pi], $$ there exists $s_1 \in R$ such that $(1_s)$ has no $2\pi$periodic solution if $s< s_1$, and at least one $2\pi$-periodic solution if $s = s_1$, and at least two $2\pi$-periodic solutions if $s > s_1$.s_1$.

• Korean Journal of Computational Design and Engineering
• /
• v.15 no.4
• /
• pp.253-260
• /
• 2010

This paper presents algorithms for computing offsets of freeform curves. The approach first divides the original curve into several segments at the inflexion points. Based on the obtained new control polygon and its offsets, quadratic trigonometric splines are constructed to approximate the offset curves. Finally, the shape parameter value of trigonometric spline is determined to satisfy the required tolerance. The degree of the output curve is two, independent of the original curve's degree. Because of the great controllability, the proposed method can generate a completely overestimating offset curve by adjusting the value of the shape parameter, which guarantees no overcutting in NC machining. Furthermore, it also produces the lowest number of control points compared with other works.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.824-827
• /
• 2006

The Prefabricated Vertical Drains (PVDs) method is one of the most widely used techniques to accelerate the consolidation process in-situ and hence increase its bearing capacity. In this paper, the degree of consolidation incorporated with PVDs was evaluated in O construction work site which composed with dredged soil. O Program PVD(Version 2.3) which developed by Asian Institute of Technology was used. The purpose of this analysis is efficiently to estimate the degree of consolidation by analyzing the surface settlement with time, and drainage at initial stage and final stage by using design-parameter which based on the in-situ tests and laboratory tests. This result can be compared with analysis of the degree of consolidation using Program PVD(Version 2.3) and the field observed data in the future studies.

• International Journal of Computer Science & Network Security
• /
• v.21 no.7
• /
• pp.93-102
• /
• 2021

This study aimed to test method on the accuracy of estimating the items parameters and ability, using the Three Parameter Logistic. To achieve the objectives of the study, an achievement test in chemistry was constructed for third-year secondary school students in the course of "natural sciences". A descriptive approach was employed to conduct the study. The test was applied to a sample of (507) students of the third year of secondary school in the "Natural Sciences Course". The study's results revealed that the (EAP) method showed a higher degree of accuracy in the estimation of the difficulty parameter and the abilities of persons higher than the MML method. There were no statistically significant differences in the accuracy of the parameter estimation of discrimination and guessing regarding the difference of the two methods: (MML) and (EAP).

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.117-122
• /
• 1994

In this paper, we discuss the modeling of flexible manipulators. In the modeling of flexible manipulators, there are two approaches: one is based on the distributed-parameter modeling and the other on the lumped-parameter modeling. The former has been applied to control and analysis of simple manipulator requiring precision, while the latter has been applied to multi-link spatial manipulator, because of the model's simplicity. We have already proposed the lumped-parameter modeling method for simple manipulator, and investigate that model of how much degree of precision we can get. The experiments and simulations are performed, comparing these results, the approximate performance of our modeling method is discussed.