• 소성∙가공
• /
• 제19권7호
• /
• pp.416-422
• /
• 2010

The $\{10\bar{1}2\}$ twinning characteristics, such as active twin variants, volume fraction of twins with strain, twin morphology, twin texture and angle relationship between twins, were dependent on the activation mode (i.e., tension parallel to the caxis or compression perpendicular to the c-axis). The selection criterion of active twin variants was governed by the Schmid law. This activation of selected twin variants depending on the activation mode consequently caused a totally different plastic deformation behavior in two activation modes. The differences in the deformation characteristics, such as flow stress and work hardening rate, between both activation modes were explained in relation with activation stresses for slips and twinning, relative activities of twinning and slips during plastic deformation, grain refining effect by twin boundaries (Hall-Petch effect), and twinning-induced change in activities of slips.

• 대한기계학회논문집A
• /
• 제26권9호
• /
• pp.1943-1951
• /
• 2002

The casting roll design is one of the most important requirements in twin roll strip casting process. Coupled analyses of heat transfer and deformation for the cast roll are carried out by use of the finite element program MARC to examine the thermal stress and deformation. The effects of several factors on thermal stress and deformation are also investigated. The amount of thermal stress increases when the ni thickness increases and when the casting speed and the copper sleeve thickness decrease.

• 터널과지하공간
• /
• 제14권5호
• /
• pp.381-390
• /
• 2004

본 연구에서는 터널간 이격거리, 지반종류, 하중조건 등이 서로 다른 11가지 쌍굴터널 모형에 대한 축소모형실험을 통하여 터널 주변지반의 변형거동을 조사하였다. 이를 위해 모래, 석고, 물의 중량비를 달리한 모형재료에 대한 물성 실험을 통해 모형재료의 특성을 연구하였다. 쌍굴터널 사이의 이격거리가 좁은 모형일수록 낮은 압력 수준에서 균열이 개시되었고 필러의 spatting현상도 잘 발달하였으며 터널의 내공변형량도 증가하였다. 경암모형은 연암 모형에 비해 평균 50% 이상 큰 하중에서 균열이 개시되었고 동일 하중하에서 내공변형량도 2배정도 작게 나타났다. 모형터널의 파괴 및 변형양상은 측압 하중조건에 따라 매우 상이하게 나타났으며, FLAC을 사용한 수치해석 결과는 모형실험의 결과와 정성적으로 부합하였다.

• 소성∙가공
• /
• 제16권6호
• /
• pp.467-472
• /
• 2007

In this study, the effects of initial texture on the twinning formation of AZ31 Mg rolled sheet was investigated. Uniaxial compression tests were carried out on samples cut along the normal direction(ND) and roiling direction(RD), respectively, of rolled AZ31 Mg alloy sheet at various temperatures (RT, 200, 250, 300, 350, $400^{\circ}C$) with the fixed strain rate($10^{-2}/s$). The results showed that deformation twining occurred actively only in the RD specimens, which promoted homogeneous deformation as compared to the ND specimens. The effect of temperature on the formation of deformation twins was also investigated, and the slip/twin transition temperature was found to be approximately $250^{\circ}C$.

• 한국정밀공학회지
• /
• 제19권11호
• /
• pp.200-210
• /
• 2002

In twin roll strip casting process, coupled analyses of heat transfer and deformation for the cast roll are carried out by using the finite element program MARC to examine the thermal crown. Shrink fit effect and plastic deformation are considered. The results shows that the thermal crown is greatly influenced by shrink ft and that the thermal crown for POSCO Pilot Caster 2 Copper Roll has “M” shape. The effects of several factors on thermal crown are also investigated. The amount of thermal crown increases as heat flux, casting speed, steeve thickness and casting roll width increase and decreases as the casting roll diameter increases.

• 열처리공학회지
• /
• 제7권2호
• /
• pp.88-95
• /
• 1994

In order to compare mechanical properties of ausformed martensite with those of marformed martemsite in Fe-30%Ni-0.1%C alloy and to investigate their strengthening mechanisms, ausformed martensite and marformed martensite were prepared by ausforming treatment and marforming treatment respectively. The microstructures were observed and the quantities of retained austenite, hardness, yield strength, ultimate tensile strength and elongation were examined. The strength of ausformed martensite was mainly increased because of the lattice defects inherited from austenite. The ductility of ausformed martensite was constant at the rate of 7-8% by ductile matrix formation of the retained austenite in spite of the increase in strength. The strength of marformed martensite was increased by the increment in dislocation density, the crossing of transformation twin with deformation twin and the mutual crossing of deformation twin. The ductility of mar formed martensite was slightly lower than that of ausformed martensite, but the strength of mar formed martensite was prominently higher.

• Applied Microscopy
• /
• 제50권
• /
• pp.19.1-19.9
• /
• 2020

Deformation twinning, one of the major deformation modes in a crystalline material, has typically been analyzed using generalized planar fault energy (GPFE) curves. Despite the significance of these curves in understanding the twin nucleation and its effect on the mechanical properties of crystals, their experimental validity is lacking. In this comparative study based on the first-principles calculation, molecular dynamics simulation, and quantitative in-situ tensile testing of Al nanowires inside a transmission electron microscopy system, we present both a theoretical and an experimental approach that enable the measurement of a part of the twin formation energy of the perfect Al crystal. The proposed experimental method is also regarded as an indirect but quantitative means for validating the GPFE theory.

• Structural Engineering and Mechanics
• /
• 제84권5호
• /
• pp.699-706
• /
• 2022

Settlement control techniques are critical for the safety of shield tunnel constructions, especially for facing complex situations. In this study, the shield tunnel structure from Huaita east road station to Heping Road station in Xuzhou metro No.3 line (China) is taken as engineering background, which has various complex problems of the upper-soft and lower-hard composite stratum conditions, twin curve shield tunnels, and underpass the foundation of the piled raft. The deformation characteristics of shield tunnelling passing through buildings are explored. Subsequently, comprehensive research methods of numerical simulation and field measurement are adopted to analyzing the effectiveness of settlement control by using the top grouting technique. The results show that the settlement of the buildings has obvious spatial characteristics, and the hysteresis effect can be obviously observed in soil deformation caused by shield construction. Meanwhile, the two shield constructions can cause repeated disturbances, reducing the soil deformation's hysteresis effect. Moreover, the shield tunnel's differential settlement is too large when a single line passes through, and the shield construction of the outer curve can cause more significant disturbance in the tunnel than the inside curve. Notably, the proposed process control parameters and secondary topgrouting method can effectively control the deformation of the shield tunnel, especially for the long-term deformation.

• Korea-Australia Rheology Journal
• /
• 제18권3호
• /
• pp.153-160
• /
• 2006

We analyzed the non-Newtonian and non-isothermal flow with Carreau-Yasuda viscosity model in co-rotating and counter-rotating twin screw extruder systems. The mixing performances with respect to the screw speed, the screw pitch, and the rotating direction have been investigated. The dynamics of mixing was studied numerically by tracking the motions of particles. The extent of mixing was characterized in terms of the deformation rate, the residence time distribution, and the average strain. The results showed that the high screw speed decreases the residence time but increases the deformation rate. Small screw pitch increases the residence time. It is concluded that the high screw speed increases the dispersive mixing performance, while the small screw pitch increases the distributive mixing performance. Co-rotating screw extruder has the better conveying performance and the distributive mixing performance than counter-rotating screw extruder with the same screw speed and pitch. Co-rotating screw extruder developed faster transport velocity and it is advantageous the flow characteristics to the mixing that transfers polymer melt from one barrel to the other barrel.

• 대한기계학회논문집A
• /
• 제26권11호
• /
• pp.2466-2473
• /
• 2002

In twin roll strip casting process, the design of casting roll is the most important equipment for producing strip. Analyses of heat transfer and deformation for the casting roll are carried out by using the finite element program, ANSYS. Both the elastic deformation and the elasto-plastic deformation under a thermal load are considered in the analysis. Optimization to minimize the volume of roll is performed under the various thermal loads such as the heat flux and the roll speed. Design variables are defined by diameters and positions of the cooling hole in the roll , Although the thermal load remarkably varies, the design variables and objective function are found to be consistent.