• 지질공학
• /
• 제17권4호
• /
• pp.655-664
• /
• 2007

터널의 설계 시 변형계수, 포아송비, 내부마찰각, 점착력 등의 지반특성치가 이용되는데, 이 중 변형계수는 터널변위에 가장 큰 영향을 준다. 그러나 암반의 변형계수는 불연속면과 시료크기 등의 영향으로 시험으로 결정하기 매우 어렵기 때문에 주로 경험적인 방법에 의존하고 있다. 본 연구에서 현장조사, 실내시험, 및 시추조사를 통해 얻은 지반특성치에 근거하여 수치해석을 실시한 결과, 계산된 변위와 현장 계측치가 일치하지 않았다. 그래서 변형계수를 변화시키면서 반복해석을 실시하여 변형계수와 터널변위의 상관성을 구하였으며, 상관관계식은 2 터널에서 얻어진 자료에 근거하여 적합성을 검증하였는데, 이 현장에서는 암반의 변형계수가 암석 탄성계수의 약 $30{\sim}40%$정도인 것으로 보인다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1245-1251
• /
• 2005

The deformation modulus is an important variable which can be used to predict settlement of structures, analyze horizontal directions of piles and design roads. Though to predict deformation modulus relationships using standard penentration test N-value and undrained shear strength were suggested , these relationships are not appropriate in domestic areas because these relationships are based on foreign areas. Therefore, in this study, with field test results, reasonable equations in domestic area are suggested to estimate deformation modulus.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.539-545
• /
• 2010

The field plate test has a good potential for determining since it measures both plate pressure and settlement. The deformation modulus of rock mass is differently measured for status of structures. The values of deformation modulus are obtained from laboratory test (uniaxial and triaxial test) and field test (pressuremeter test). Plate load test should be conducted by different loading plate sizes for geological structure of rock mass and scale of structures. In this paper, large plate load tests were performed to predict of structure's behavior and evaluate the ultimate bearing capacity of the foundation on soft rock. Simultaneously, deformation modulus of rock mass was estimated by back analysis of stresses measured in field test under rock mass. Finally, we verified the validation of deformation modulus of rock mass through result of large plate load test and numerical simulation.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.484-491
• /
• 2008

The purpose of this study is to compare the cementation effect on cone resistance and DMT indices and to evaluate the deformation characteristic of cemented sand using cone resistance and dilatometer modulus. Specimens of various relative densities with three different cementation levels are prepared in a large calibration chamber under different vertical stress levels. Test result shows that the cone resistance and dilatometer modulus underestimate the deformation modulus of cemented sand, since in situ penetration tests such as CPT and DMT damage the cementation bonds during penetration. By regression analysis, the constrained modulus of cemented sand is related with the cone resistance and the dilatometer modulus.

• 한국지반환경공학회 논문집
• /
• 제18권5호
• /
• pp.17-26
• /
• 2017

절리가 형성된 암반지층에서의 터널굴착은 터널굴착 선을 따라 변위를 유발시키며 이러한 변위값의 산정은 터널의 안정성과 소요공간을 확보하는 것과 관련하여 매우 중요한 사항이다. 터널변위는 지반의 변형계수와 직접적으로 관련되므로 이를 파악하는 것이 무엇보다도 중요하다. 그렇지만, 터널이 건설되는 대부분의 암반지층은 일반적으로 절리가 형성되어 있어서 단순히 균질한 등가탄성매질에 근거하여 절리형성 암반지층의 변형계수를 파악할 수는 없다. 왜냐하면 절리형성 암반지층의 변형계수는 암석의 종류뿐만 아니라 절리조건에 의해서 큰 영향을 받기 때문이다. 따라서 본 연구에서는 터널굴착 조건에서 다양한 절리 및 암석조건을 고려한 암반지층의 변형계수 변화를 조사하였으며 이를 위하여 수치해석적 매개변수연구를 수행하였다. 이를 통한 본 연구의 결과는 기존의 경험적인 방법들과 상호 비교되었으며, 또한 다양한 절리암반을 고려한 변형계수 변화표의 형태로서 제시되었다.

• Structural Engineering and Mechanics
• /
• 제69권5호
• /
• pp.557-566
• /
• 2019

The reservoir basin bedrock produced significant impact on the long-term service safety of super-high arch dams. It was important for accurately identifying geomechanical parameters and its evolution process of reservoir basin bedrock. The deformation modulus mechanism research methods of reservoir basin bedrock deformation modulus for super-high arch dams was carried out by finite element numerical calculation of the reservoir basin bedrock deformation and in-situ monitoring data analysis. The deformation modulus inversion principle of reservoir basin bedrock in a wide range was studied. The convergence criteria for determining the calculation range of reservoir basin of super-high arch dams was put forward. The implementation method was proposed for different layers and zones of reservoir basin bedrock. A practical engineering of a super-high arch dam was taken as the example.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1998년도 가을 학술발표회 논문집
• /
• pp.49-56
• /
• 1998

• Geomechanics and Engineering
• /
• 제17권3호
• /
• pp.247-252
• /
• 2019

Modulus of deformation of soil is an essential parameter used for design analysis of foundations, despite its importance; little attention is paid to developing empirical models for predicting the sensitivity of deformation moduli to other parameters that obtained from the pressuremeter tests. Various methods of analysis used to predict the horizontal at rest pressure from pressuremeter testing ($P_o$), these values showed distinctive variations, five methods used to evaluate the values of horizontal at rest pressure, these values been used to evaluate the modulus of elasticity using three methods of analysis. The values of modulus showed distinctive increase when the values of horizontal at rest pressure increase for the same pressuremeter test, these increases may reach to 65%. This sensitivity of the moduli to values of horizontal lead the author to propose some reliable methods of analysis for both the horizontal at rest pressure and the modulus of deformation from pressuremeter testing.

• 터널과지하공간
• /
• 제2권2호
• /
• pp.237-250
• /
• 1992

The cavities formed by the excavation of coal seam cause unstable within rock body, leading to large displacement around adjacent roadway. This displacement brings the closure of roadway and deformation of support. Therefore, it is necessary to understand and predict the deformation characteristics of roadway while coal seam is under excavation. In this study, the observed displacements are compared with the calculated ones through the analysis using Linear Boundary Element Mothod under the elastostatic conditions, in order to determine the virgin stress state and deformation modulus which affect the deformation characteristices.

• Geomechanics and Engineering
• /
• 제22권4호
• /
• pp.277-290
• /
• 2020

This paper presents an elastic-plastic solution for the circular tunnel of elastic-strain softening behavior considering the pressure-dependent Young's modulus and the nonlinear dilatancy. The proposed solution is verified by the results of the field measuring and numerical simulation from a practical project, and a published closed-form analysis solution. The influence of each factor is discussed in detail, and the ability of Young's modulus and dilatancy characterizing the mechanical response of surrounding rock is investigated. It is found that, in low levels of support pressure, adopting the constant Young's modulus model will seriously misestimate the surrounding rock deformation. Using the constant dilatancy model will underestimate the surrounding rock deformation. When adopting the constant dilatancy model, as the dilation angle increases, the range of the plastic region increases, and the surrounding rock deformation weakens. When adopting the nonlinear dilatancy, the plastic region range and the surrounding rock deformation are the largest. The surrounding rock deformation using pressure-dependent Young's modulus model is between those resulted from two constant Young's modulus models. The constant α of pressuredependent Young's modulus model is the main factor affecting the tunnel displacement. The influence of α using a constant dilatancy model is much more apparent than that using a nonlinear dilatancy model.