• 한국농공학회논문집
• /
• 제46권1호
• /
• pp.41-51
• /
• 2004

FRP re-bar in concrete structures could be used as a substitute of steel re-bars for that cases in which aggressive environment produce high steel corrosion, or lightweight is an important design factor, or transportation cost increase significantly with the weight of the materials. But FRP fibers have only linearly elastic stress-strain behavior; whereas, steel re-bar has linear elastic behavior up to the yield point followed by large plastic deformation and strain hardening. Thus, the current FRP re-bars are not suitable concrete reinforcement where a large amount of plastic deformation prior to collapse is required. The main objectives of this study in to evaluate the tensile behavior and the fracture mode of hybrid FRP re-bar. Fracture mode of hybrid FRP re-bar is unique. The only feature common to the failure of the hybrid FRP re-bars and the composite is the random fiber fracture and multilevel fracture of sleeve fibers, and the resin laceration behavior in both the sleeve and the core areas. Also, the result of the tensile and interlaminar shear stress test results of hybrid FRP re-bar can provide its excellent tensile strength-strain and interlaminar stress-strain behavior.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.279-282
• /
• 2005

Composites comprising various volume fractions of crystalline nickel and bulk amorphous (BA) were produced by means of electroless coating of nickel on BA powder of $Cu_{54}Ni_6Zr_{22}Ti_{18}$ and subsequent spark plasma sintering (SPS) of coated BA powder. The flow curves of composites at various temperatures in the supercooled liquid region were determined by the uniaxial compression test with various strain rates. During compression at $450^{\circ}C$ with $\dot{\varepsilon}=2\times10^{-3}$, the monolithic BA sample and crystalline-BA composites displayed the superplastic deformation with $\varepsilon>1.4$. At temperatures above $460^{\circ}C$, the stress-strain curve of the monolithic BA sample depicted a sharp peak stress and a fellowing stress drop due to cracking, while those of the crystalline-BA composites displayed work-hardening up to the imposed strain. FEM analysis indicated that a fairly homogeneous strain state prevailed throughout the composite, while a higher level of stress was obtained in a harder BA.

• Geomechanics and Engineering
• /
• 제7권2호
• /
• pp.213-231
• /
• 2014

An elastoplastic model for structured clays, which is formulated based on the fact that the difference in mechanical behavior of structured and reconstituted clays is caused by the change of fabric in the post-yield deformation range, is present in this paper. This model is developed from an elastoplastic model for overconsolidated reconstituted clays, by considering that the variation in the yield surface of structured clays is similar to that of overconsolidated reconstituted clays. However, in order to describe the mechanical behavior of structured clays with precision, the model takes the bonding and parabolic strength envelope into consideration. Compared with the Cam-clay model, only two new parameters are required in the model for structured clays, which can be determined from isotropic compression and triaxial shear tests at different confining pressures. The comparison of model predictions and results of drained and undrained triaxial shear tests on four different marine clays shows that the model can capture reasonable well the strength and deformation characteristics of structured clays, including negative and positive dilatancy, strain-hardening and softening during shearing.

• 소성∙가공
• /
• 제28권5호
• /
• pp.266-274
• /
• 2019

Metal sealing is used to connecting the parts between valves and fuel pipes for a FCEV which utilizes hydrogen gas of 700 bar. Instead of general carbon steel, stainless steel is the primary material used to manufacture fuel pipes due to hydrogen embrittlement. The shape of deformation between metals is an important factor on the air-tightness of the metal to metal contact. Since the stainless steel pipe is hardened using the plastic forming during the tip shaping stage, this work hardening could have an effect on the deformed shape and characteristics of contact surfaces in fastening of pipes. In this paper, the deformation history of the pipe model was considered in order to analyze the hydrogen-tightness on the metal sealing part. The contact distance and the forward displacement for fastening were compared using experimental results and the simulation results. The simulation of the effect of material change on the fitting body demonstrated that the hardness or the strength of the formed tip of the pipe was designed to a proper valued level since the characteristics of the contact surface was exhibited better when the strength of the pipe was lower than that of the fitting body.

• Coupled systems mechanics
• /
• 제8권3호
• /
• pp.273-287
• /
• 2019

Elastoplastic analysis of an annular disc, being fully constrained on its outer rim and interacting with a purely elastic inclusion perfectly bonded with its inner rim, is conducted to study its plastic deformation and residual stress under thermal cycles. The system is termed the composite disc. Quasi-static plane-strain deformation is assumed, and the von Mises yield criterion with or without the Ludwik hardening rule is adopted in our finite element calculations. Effects of multiple material properties simultaneously being temperature dependent on the plastic behavior of the composite disc are considered. Residual stress is analyzed from a complete loading and unloading cycle. Results are discussed for various inclusion radii. It is found that when temperature dependent material properties are considered, the maximum residual stress may be greater than the maximum stress inside the disc at the temperature-loaded state due to lower temperature having larger yield stress. Temperature independent material properties overestimate stresses inside materials, as well as the elastic irreversible temperature and plastic collapse temperature.

• 소성∙가공
• /
• 제32권2호
• /
• pp.53-60
• /
• 2023

A wide range of grain size was achieved in a Fe-Cr-Mn austenitic stainless steel (STS) by cold rolling and reversion annealing. The tensile characteristics of the STS were analyzed in terms of the dependence of strain induced martensitic (SIM) transformation on the grain size. In the ultrafine grain regime, the steel showed a high yield strength over 1 GPa, a discontinuous yielding, and a prolonged yield point elongation followed by considerable strain hardening. By increasing the grain size, the discontinuous yielding diminished and the yield point elongation decreased. The microstructural examination revealed that these tensile characteristics are closely related to the suppression of SIM transformation with decreasing the grain size. Especially, the prolonged yield point elongation of the ultrafine grained STS was found to be associated with development of unidirectional ε martensite bands. Based on the microstructural examination of the deformed microstructures, the rationalization of the grain size dependence of SIM transformation was suggested.

• 한국전산구조공학회논문집
• /
• 제23권1호
• /
• pp.81-94
• /
• 2010

본 연구는 선형 상보법으로 초고강도 섬유보강 콘크리트 I형보의 파괴역학적 해석을 수치해석으로 수행하였다. 기존의 보통강도 콘크리트에 대한 유사 취성 파괴역학적 수치해석을 기반으로 초고강도 섬유보강 콘크리트 재료역학적 구성모델파괴 면에 인장경화 관계를 도입함으로써 초고강도 섬유보강 콘크리트 I형 거더 해석을 개선시켰다. 상수변형률 삼각형 요소에 꼭지점 또는 요소의 중앙점 절점을 배제하고 요소의 변에 절점을 배치한 결합된 삼각형 요소를 사용하였다. 인장영역에서는 경화/연화 파괴역학적 구성모델을, 전단영역에서는 연화 파괴역학적 구성모델을, 경계절점의 압축에 대해서는 연화파괴역학적 구성모델을 사용하여 파괴역학적 해석을 수행하였다. Non-holonomic rate 형태로 경로에 의존적인 경화연화거동을 LCP로 방정식을 구성하였으며, 그 해는 PATH를 사용해서 구하였다. Piece-wise 비탄성 항복-파괴면은 두 개의 압축 caps, 두 개의 Mohr-Coulomb 파괴면, 인장항복면과 인장파괴면 등으로 구성하였다. 초고강도 섬유보강 콘크리트 거더의 변형거동과 파괴 상태와 비교하여 이 수치해석 방법에 대한 유효성을 검증하였다.

• 한국지반신소재학회논문집
• /
• 제21권4호
• /
• pp.69-78
• /
• 2022

지오튜브 공법은 해안지역 해안선 침식방지와 준설토 매립 호안사면의 뒤채움 필터석 대체용으로도 널리 활용되고 있다. 본 연구는 지오텍스타일에 의해 보강되어 제작된 공시체를 현장 상태를 고려하여 등방 구속압력 10kPa, 50kPa, 100kPa 이하로 최소화하여 연직응력 재하 시 변형 거동을 파악하였다. 시험결과 공시체의 연직 변형율 7%까지는 구속압(≤100kPa)에 관계없이 지오텍스타일 조직의 이완에 따른 인장력이 발휘되는 초기 Strain Hardening 영향으로 응력-변위 거동은 동일하였다. 변형율 7%이상부터는 구속압력이 작은 공시체는 재하 시 변형이 커서 보강 지오텍스타일의 인장 저항력을 증가시키므로 Strain Hardening에 의해 파괴 시 축차응력은 상대적으로 증가하였다. 파괴 후는 급격하게 Strain Softening에 의해 취성파괴형태를 나타내면서 저하되었다. 이는 일반적인 삼축압축시험에서 셀 압이 증가되면서 전단응력도 크게 증가되는 현상과 다르다. 지오텍스타일 등방구속시험에서는 지오텍스타일의 인장변위가 일차적으로 영향을 받기 때문에 탄성계수를 급격하게 증가시키는 탄성 거동을 나타내고 있다.

• 대한토목학회논문집
• /
• 제44권1호
• /
• pp.109-116
• /
• 2024

초속경 복합매트(Rapid Hardening Composite Mat)는 기존 GCCM의 초기 강도 발현 속도를 향상시킨 제품으로, 시공기면이 부족한 철도 비탈면에서 신속한 시공기면 확보가 가능하고 비탈면 유실 방지 및 식생억제가 가능한 장점이 있다. 본 연구에서는 실험을 통해 초속경 복합매트의 철도 현장 적용성을 분석하였다. 현장 적용성은 내화성, 내구성, 안정성으로 구분하여 난연 시험, 접지압 실험, 일일 변위량 분석을 통해 분석하였다. 국토 대부분이 산림구조로 이루어진 국내의 경우 비탈면 화재 예방이 필수적이며, 초속경 복합매트의 내화성을 분석하기 위해 난연 시험을 수행하였다. 내구성은 시공기면에 불가피하게 투입되는 중·소형 장비에 의한 초속경 복합매트의 변형 및 파괴 여부를 분석하기 위해 접지압 실험을 수행하였다. 또한 일일 변위량 분석은 초속경 복합매트 적용 시 발생되는 변위 및 거동을 철도 비탈면 관리기준과 비교·분석하여 구조적 안정성을 평가하기 위해 수행하였다. 실내시험 결과, 초속경 복합매트는 열방출률 및 가스유해성 판정기준에 충족하는 것으로 분석되었으며 재령 4시간~24시간 초속경 복합매트의 접지압은 모든 조건에서 약 50 kPa 이상인 것으로 나타났다. 또한 현장실험을 통해 분석한 일일 변위량은 -1.7 mm~1.01 mm로 나타나, 기준치에 만족하는 것을 확인하였다.

• 열처리공학회지
• /
• 제7권1호
• /
• pp.44-52
• /
• 1994

In order to investigate the effect of tempring treatment on the mechanical properties of ausformed martensite in Fe-30%Ni-0.35%C alloy, the hardness, yield strength and elongation were examined by tensile test. 1. The strength of deformed austenite in Fe-30%Ni-0.35%C alloy was increased due to the work hardening induced from the dislocation density increased during deformation. The strength of ausformed martensite was increased because of defects inherited from deformed austenite by martensitic transformation. 2. The ductility of ausformed martensite was shown a nearly constant values independent of deformation degrees because of the interaction of multiple factors such as increased retained austenite, formation of void and decrement of twin in ausformed martensite. 3. The strength of ausformed martensite by tempering treatment was shown a little decrement up to $340^{\circ}C$, especially showed remarkable softening resistance in higher deformation degrees. 4. Virgin martensite and ausformed martensite were shown a maximum yield strength by clustering in tempering at $100^{\circ}C$ and above $100^{\circ}C$, yield strength was very small decreased due to the decrement of solute carbon by the destruction of clustering. 5. The decomposition of retained austenite was not shown up to $450^{\circ}C$ in ausformed martensite with tempering treatment, and the matrix was rapidly softening because of the decomposition of martensite and the formation of reversed austenite with tempering above $400^{\circ}C$.