• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.324-326
• /
• 2016

In this study, we have investigated indium tin zinc oxide (ITZO) as an active channel for non-volatile memory (NVM) devices. The electrical and memory characteristics of NVM devices using multi-stack gate insulator SiO2/SiOx/SiOxNy (OOxOy) with Si-rich SiOx for charge storage layer were also reported. The transmittance of ITZO films reached over 85%. Besides, ITZO-based NVM devices showed good electrical properties such as high field effect mobility of 25.8 cm2/V.s, low threshold voltage of 0.75 V, low subthreshold slope of 0.23 V/dec and high on-off current ratio of $1.25{\times}107$. The transmission Fourier Transform Infrared spectroscopy of SiOx charge storage layer with the richest silicon content showed an assignment at peaks around 2000-2300 cm-1. It indicates that many silicon phases and defect sources exist in the matrix of the SiOx films. In addition, the characteristics of NVM device showed a retention exceeding 97% of threshold voltage shift after 104 s and greater than 94% after 10 years with low operating voltage of +11 V at only 1 ms programming duration time. Therefore, the NVM fabricated by high transparent ITZO active layer and OOxOy memory stack has been applied for the flexible memory system.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.2
• /
• pp.127-134
• /
• 2017

In this study, moist curing equipment was used in the exist gang-form system. By achieving sufficient spray curing, the quality of the concrete was improved and the cracking occurred in building's side wall was decreased. The following results could be made as the conclusion. For the compressive strength, all zones showed the similar results. Comparing with the zone without using moist curing equipment, the zone used moist curing equipment showed higher rebound hardness results. For the cracking, the zone utilized moist curing equipment showed the cracking averaged as 6.6 m and the zone without using moist curing equipment showed the cracking averaged as 10.3m. The effectof reducing cracking by utilizing moist curing equipment is about 36 %. Using moist curing equipment is considered as a good solution to reduce the cracking in the structure. Considering all the factors analysed, using moist curing equipment improved the quality of the concrete and decreased the cracking. When this equipment was used in the construction site, it is expected that the construction periodcan be shrunk and the ratio of defect caused by drying shrinkage can be decreased. In this research conditions, The 0.3mm sized moist curing equipment provided the most desirable results on concrete quality and preventing cracking.

• Neonatal Medicine
• /
• v.25 no.3
• /
• pp.102-108
• /
• 2018

Purpose: Congenital diaphragmatic hernia (CDH) is rare but potentially fatal. The overall outcome is highly variable. This study aimed to identify a simple and dynamic parameter that helps predict the mortality of CDH patients in real time, without invasive tests. Methods: We conducted a retrospective chart review of 59 CDH cases. Maternal and fetal information included the gestational age at diagnosis, site of defect, presence of liver herniation, and lung-to-head ratio (LHR) at 20 to 29 weeks of gestational age. Information regarding postnatal treatment, including the number of days until surgery, the need for inhaled nitric oxide (iNO), the need for extracorporeal membrane oxygenation (ECMO), and survival, was collected. The highest respiratory severity score (RSS) within 24 hours after birth was also calculated. Results: Statistical analysis showed that a younger gestational age at the initial diagnosis (P<0.001), a lower LHR (P=0.001), and the presence of liver herniation (P=0.003) were prenatal risk factors for CDH mortality. The RSS and use of iNO and ECMO were significant factors affecting survival. In the multivariate analysis, the only remaining significant risk factor was the highest preoperative RSS within 24 hours after birth (P=0.002). The area under the receiver operating characteristic curve was 0.9375, with a sensitivity of 91.67% and specificity of 83.87% at the RSS cut-off value of 5.2. The positive and negative predictive values were 82.14% and 92.86%, respectively. Conclusion: Using the RSS as a prognostic predictor with simple calculations will help clinicians plan CDH management.

• Applied Chemistry for Engineering
• /
• v.10 no.1
• /
• pp.80-84
• /
• 1999

$Li_{4/3}Mn_{5/3}O_4$ having a defect structure was prepared by sol-gel process using lithium acetate and manganese acetate as starting materials, and their electrode characteristics in the lithium secondary battery was investigated. The reaction mole ratio was determined as $AA/Mn(OAc)_2$ of 0.2 and $NH_4OH/Mn(OAc)_2$ to $H_2O/Mn(OAc)_2$ of 0.4. The product was obtained through heat treatment at $350^{\circ}C$ for 12hrs after 1'st heat treatment at $150^{\circ}C$ of xerogel under oxygen atmosphere. When the charge and discharge cycles were performed between 2.0 V and 3.2 V, $Li/Li_{4/3}Mn_{5/3}O_4$ cell showed the dicharge capacity of 84.23 mAh/g and the good cycleability was obtained in the plateau region.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.17.2-17.2
• /
• 2011

Double-walled carbon nanotubes (DWCNTs) were grown with vertical alignment on a Si wafer by using catalytic thermal chemical vapor deposition. This study investigated the effect of pre-annealing time of catalyst on the types of CNTs grown on the substrate. The catalyst layer is usually evolved into discretely distributed nanoparticles during the annealing and initial growth of CNTs. The 0.5-nm-thick Fe served as a catalyst, underneath which Al was coated as a catalyst support as well as a diffusion barrier on the Si substrate. Both the catalyst and support layers were coated by using thermal evaporation. CNTs were synthesized for 10 min by flowing 60 sccm of Ar and 60 sccm of H2 as a carrier gas and 20 sccm of C2H2 as a feedstock at 95 torr and $750^{\circ}C$. In this study, the catalyst and support layers were subject to annealing for 0~420 sec. As-grown CNTs were characterized by using field emission scanning electron microscopy, high resolution transmission electron microscopy, Raman spectroscopy, and atomic force microscopy. The annealing for 90~300 sec caused the growth of DWCNTs as high as ~670 ${\mu}m$ for 10 min while below 90 sec and over 420 sec 300~830 ${\mu}m$-thick triple and multiwalled CNTs occurred, respectively. Several radial breathing mode (RBM) peaks in the Raman spectra were observed at the Raman shifts of 112~191 cm-1, implying the presence of DWCNTs, TWCNTs, MWCNTs with the tube diameters 3.4, 4.0, 6.5 nm, respectively. The maximum ratio of DWCNTs was observed to be ~85% at the annealing time of 180 sec. The Raman spectra of the as-grown DWCNTs showed low G/D peak intensity ratios, indicating their low defect concentrations. As increasing the annealing time, the catalyst layer seemed to be granulated, and then grown to particles with larger sizes but fewer numbers by Ostwald ripening.

• Archives of Reconstructive Microsurgery
• /
• v.5 no.1
• /
• pp.128-136
• /
• 1996

Radial nerve injury is caused by variety of etiologies, mainly traumatic. It is primarily a motor nerve and loss of it's function leads to a significant disability. Surgical treatments of radial nerve comprise of neurolysis(internal or external), neurorrhaphy(eineural, perineural or epi-perineural), nerve graft and tendon transfer. However, there is still controversies in treatment methods and time of operation. Authors experienced 23 cases of radial nerve injuries who were treated by operative methods and followed up over 1 year's duration. The male to female ratio was 18 to 5 and mean age was 30.7 years old. The causes were 13 cases in fractures, 5 cases in crushing injury, 3 cases in laceration, 1 case in CO poisoning and 1 case in unknown cause. The summary of the study were as follows ; 1. Excellent or good results were obtained in overall 16 cases among 23 cases; 5 of 9 cases in neurolysis, 3 of 3 cases in neurorrhaphy, 2 of 3 cases in nerve graft and 6 of 8 cases in tendon transfer. 2. In cases of neurorrhaphy and nerve graft, primary or delayed repair showed excellent or good results and neurolysis performed before 6 months leads to better results. But there was no correlations between the time of injury and operation in tendon transfer. 3. The radial nerve injury associated with extensive soft tissue defect or any conditions that leads to nerve ischemia results poor prognosis. 4. The patients aged under 40 years showed better prognosis in clinical results according to the age of surgical treatment. 5. If the surgeon decide the method and the time of operation through the exact evaluation of the factors which influencing the end result such as age of the patient, level and type of injury, extent of nerve lesion and the associated tissue injury, good result could be expected.

• Tribology and Lubricants
• /
• v.34 no.4
• /
• pp.146-159
• /
• 2018

This paper presents a wear analysis procedure for calculating the wear of journal bearings of a four-strokes and four-cylinder engine operating at a constant angular crank shaft speed during firing conditions. To decide whether the lubrication state of a journal bearing is in the possible region of wear scar, we utilize the concept of the centerline average surface roughness to define the most oil film thickness scarring wear (MOFTSW) on two rough surfaces. The wear volume is calculated from the wear depth and wear angle, determined by the magnitude of each film thickness on a set of oil films with thicknesses lower than the MOFTSW at every crank angle. To calculate the wear volume at one contact, the wear range ratio during one cycle is used. The total wear volume is then determined by accumulating the wear volume at every contact. The fractional film defect coefficient, asperity load sharing factor, and modified specific wear rate for the application of the mixed-elasto-hydrodynamic lubrication regime are used. The results of this study show that wear occurs only at the connecting-rod big-end bearing. Thus, simulation results of only the big-end bearing are illustrated and analyzed. It is shown that the wear volume of each wear scar group occurs consecutively as the crank angle changes, resulting in the total accumulated wear volume.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.11
• /
• pp.1896-1911
• /
• 1997

Effects of fiber-matrix interphases on the micro-and macro-mechanical behaviors of unidirectionally fiber-reinforced composites subjected to transverse shear loading at remote distance have been studied. The interphases between fibers and matrix have been modeled by the spring-layer which accounts for continuity of tractions, but allows radial and circumferential displacement jumps across the interphase that are linearly related to the normal and tangential tractions. Numerical calculations for basic cells of the composites have been carried out using the boundary element method. For an undamaged composite the micro-level stresses at the matrix side of the interphase and effective shear stiffness have been computed as functions of fiber volume ratio $V_f$ and interphase stiffness k. Results are presented for various interphase stiffnesses from the perfect bonding to the case of total debonding. For a square array composite the results show that for a high interphase stiffness k>10, an increase of $V_f$ increases the effective transverse shear modulus G over bar of the composite. For a relatively low interphase stiffness k<1, it is shwon that an increase of $V_f$ slightly decreases the effective transverse shear modulus. For the perfect bonding case, G over bar for a hexagonal array composite is slightly larger than that for a square array composite. Also for a damaged composite partially debonded at the interphase, local stress fields and effective shear modulus are calculated and a decrease in G over bar has been observed.

• International Journal of Vascular Biomedical Engineering
• /
• v.2 no.1
• /
• pp.11-16
• /
• 2004

Both flow visualizations and computational fluid dynamics were performed to determine hemodynamics in a total cavopulmonary connection (TCPC) model for surgically correcting congenital heart defects. From magnetic resonance images, an anatomically correct glass model was fabricated to visualize steady flow. The total flow rates were 4, 6 and 8L/min and flow rates from SVC and IVC were 40:60. The flow split ratio between LPA and RPA was varied by 70:30, 60:40 and 50:50. A pressure-based finite-volume software was used to solve steady flow dynamics in TCPC models. Results showed that superior vena cava(SVC) and inferior vena cava(IVC) flow merged directly to the intra-atrial conduit, creating two large vortices. Significant swirl motions were observed in the intra-atrial conduit and pulmonary arteries. Flow collision or swirling flow resulted in energy loss in TCPC models. In addition, a large intra-atrial channel or a sharp bend in TCPC geometries could influence on energy losses. Energy conservation was efficient when flow rates in pulmonary branches were balanced. In order to increase energy efficiency in Fontan operations, it is necessary to remove a flow collision in the intra-atrial channel and a sharp bend in the pulmonary bifurcation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.311-311
• /
• 2013

The resistance switching memory devices have several advantages to take breakthrough for the limitation of operation speed, retention, and device scale. Especially, the metal-oxide materials such as ZnO are able to fabricate on the flexible and visible transparent plastic substrate. Also, the quantum dots (QDs) embedded in dielectric layer could be improve the ratio between the low and the high resistance becauseof their Coulomb blockade, carrier trap and induced filament path formation. In this study, we irradiated 0.2-MeV-electron beam on the ZnO/QDs/ZnO structure to control the defect and oxygen vacancy of ZnO layer. The metal-oxide QDs embedded in ZnO layer on Pt/glass substrate were fabricated for a memory device and evaluated electrical properties after 0.2-MeV-electron beam irradiations. To formation bottom electrode, the Pt layer (200 nm) was deposited on the glass substrate by direct current sputter. The ZnO layer (100 nm) was deposited by ultra-high vacuum radio frequency sputter at base pressure $1{\times}10^{-10}$ Torr. And then, the metal-oxide QDs on the ZnO layer were created by thermal annealing. Finally, the ZnO layer (100 nm) also was deposited by ultra-high vacuum sputter. Before the formation top electrode, 0.2 MeV liner accelerated electron beams with flux of $1{\times}10^{13}$ and $10^{14}$ electrons/$cm^2$ were irradiated. We will discuss the electrical properties and the physical relationships among the irradiation condition, the dislocation density and mechanism of resistive switching in the hybrid memory device.