• Journal of the Korean Vacuum Society
• /
• v.10 no.3
• /
• pp.335-340
• /
• 2001

$Ga_2O_3$(1 wt%)-doped ZnO(GZO) thin films were grown on ${\alpha}-Al_2O_3$ (0001) by rf magnetron sputtering at $510^{\circ}C$, whose crystal structure was polycrystalline. As-grown GZO thin film shows poor electrical properties and photoluminescence (PL) spectra. To improve these properties, GZO thin films were annealed at 800-$900^{\circ}C$ in $N_2$atmosphere for 3 min. After the rapid thermal annealing(RTA), deep defect-level emission disappears and near-band emission is greatly enhanced. Annealed GZO thin films show very low resisitivity of $2.6\times10^{-4}\Omega$/cm with $3.9\times10^{20}/\textrm{cm}^3$ carrier concentration and exceptionally high mobility of 60 $\textrm{cm}^2$/V.s. These improved physical properties are explained in terms of translation of doped-Ga atoms from interstitial to substitutional site.

• Journal of the Korean Vacuum Society
• /
• v.14 no.2
• /
• pp.91-96
• /
• 2005

The silicon-on-insulator (SOI) wafer fabrication technique has been developed by using ion-cut process, based on proton implantation and wafer bonding techniques. It has been shown by SRIM simulation that 65keV proton implantation is required for a SOI wafer (200nm SOI, 400nm BOX) fabrication. In order to investigate the optimum proton dose and primary annealing condition for wafer splitting, the surface morphologic change has been observed such as blistering and flaking. As a result, effective dose is found to be in the $6\~9\times10^{16}\;H^+/cm^2$ range, and the annealing at $550^{\circ}C$ for 30 minutes is expected to be optimum for wafer splitting. Direct wafer bonding is performed by joining two wafers together after creating hydrophilic surfaces by a modified RCA cleaning, and IR inspection is followed to ensure a void free bonding. The wafer splitting was accomplished by annealing at the predetermined optimum condition, and high temperature annealing was then performed at $1,100^{\circ}C$ for 60 minutes to stabilize the bonding interface. TEM observation revealed no detectable defect at the SOI structure, and the interface trap charge density at the upper interface of the BOX was measured to be low enough to keep 'thermal' quality.

• Journal of the Korean Vacuum Society
• /
• v.15 no.2
• /
• pp.216-222
• /
• 2006

In this paper, we investigated the effect of hydrogen-plasma (H-plasma) treatment on the electrical and optical properties of a quantum dot infrared photodetector (QDIP) with a 5-stacked InAs dots in an InGaAs/GaAs well structure and $Al_{0.3}Ga_{0.7}As/GaAs$ SL (superlattice) current blocking layer. It has been observed that H-plasma treatment didn't affect the band structure of QDIP. It has been also observed that the H-plasma treatment on the QDIP not only enhance the electrical property of QDIP by curing the defect channels in $Al_{0.3}Ga_{0.7}As/GaAs$ SL but also introduce defects in QDIP structure. The H-plasma treatment for 10 min with 20 W of RF power provided the lowest dark current, which made it possible to measure the photo-current (PC) of QDIP whose PC was not detectable without the H-plasma treatment due to the high dark current.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.4
• /
• pp.421-439
• /
• 2003

Statement of problem : It is difficult to obtain a good titanium casting body using the traditional sprue design because of high melting point of Ti, and the low fluidity and high reactivity of molten Ti. Purpose : A new sprue design for titanium casting bodies needs more trial and error. In order to decrease the number of trial and error, computer simulation(MAGMASOFT, Magmasoft Giessereitechnologie GmbH, Achen, Germany) was used to optimize sprue design in U-shaped implant superstructures. Material and method : Five kinds of sprue were examined for the design of the sprue former for titanium casting: Sprue design A(sprue length 4 mm, rectangular shape, 4 sprues), Sprue design B(sprue length 4 mm. round shape. radius 2 mm, 7 sprues), Sprue design C (sprue length 2 mm, round shape, radius 2 mm, 7 sprues). Sprue design D (sprue length 2 mm, cone shape, large radius 3mm. small radius 2mm, 7 sprues), and Sprue design E( sprue length 2 mm. one unit channel shape). Sprue design F(sprue length 2mm, one unit channel shape) was also examined for the design of the customized sprue former in the Biotan system(Schutz Dental Gmbh, Germany). The casting bodies were taken in Sprue design A, Sprue design D, Sprue design E, and Sprue design F in the Biotan casting system. The numerically predicted defects were compared with the experimental dental castings by the radiographic and sectional view observations. Results : 1. According to the result of computer simulation, turbulence during mold filling was decreased in the sequence of Sprue design F, Sprue design E, Sprue design D, Sprue design C, Sprue design B, and Sprue design A. 2. The calculated solidification time contours indicate that hot spot was moved from the casting body to the sprue button in the sequence of Sprue design A, Sprue design B, Sprue design C, Sprue design D, and Sprue design E. The filling pattern of Sprue design F was similar to that of Sprue design E. 3 The predicted filling pattern shows that less turbulence was found in the customized sprue former than in the standard sprue former. 4. According to the results of the radiographic and cross sectional observations, casting defects less than 1mm were found at the center of a casting body with Sprue design E and Sprue design F. However, larger casting defects of 4mm were found in a casting with Sprue design A. 5. The predicted casting porosity was similar to that of the real casting. Conclusion : One unit channel-type and customized sprue former can be recommended. Further research and developement of various sprue designs using computer simulation in necessary to optimize casting design, in order to reduce the formation of casting defects in implant titanuim super-structures.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.5
• /
• pp.196-201
• /
• 2014

We investigated defects and surface polarity in AlN and GaN by using wet chemical etching. Therefore, the effectiveness and reliability of estimating the single crystals by defect selective etching in NaOH/KOH eutectic alloy have been successfully demonstrated. High-quality AlN and GaN single crystals were etched in molten NaOH/KOH eutectic alloy. The etching characteristics and surface morphologies were carried out by scanning electron microscope (SEM) and atomic force microscope (AFM). The etch rates of AlN and GaN surface were calculated by etching depth as a function of etching time. As a result, two-types of etch pits with different sizes were revealed on AlN and GaN surface, respectively. Etching produced hexagonal pits on the metal-face (Al, Ga) (0001) plane, while hexagonal hillocks formed on the N-face. On etching rate calibration, it was found that N-face had approximately 109 and 15 times higher etch rate than the metal-face of AlN and GaN, respectively. The size of etch pits increased with an increase of the etching time and they tend to merge together with a neighbouring etch pits. Also, the chemical mechanism of each etching process was discussed. It was found that hydroxide ion ($OH^-$) and the dangling bond of nitrogen play an important role in the selective etching of the metal-face and N-face.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.2
• /
• pp.89-93
• /
• 2017

GaN single crystals were grown by controlling of various processing parameters such as growing temperature, V/III ratio and growing rate. We optimized thickness of bulk GaN single crystal by analyzing defect of surface and inside of the GaN single crystal for application to high brightness and power device. 2-inch bulk GaN single crystals were grown by HVPE (hydride vapor phase epitaxy) on sapphire and their thickness was 0.3~7.0 mm. Crystal structure of the grown bulk GaN was analyzed by XRD (X-ray diffraction). The surface characteristics of the grown bulk GaN were observed by OM (optical microscope) and SEM (scanning electron microscopy) with measuring EPD (etch pits density) of the GaN crystals.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.28 no.4
• /
• pp.348-355
• /
• 2006

Tennison was the first to recognize and to preserve the Cupid's bow by lowering the peak in the margin of the cleft. Randall had modified the Tennison's repair based on accurate measurements. Bardach's technique evolved from the basic concept of triangular flap cleft lip repair described by Tennison-Randall method. Precise measurements are used to define the dimensions of the equilateral triangular flap, which is created on the cleft side and is inserted into an equilateral triangular defect on the noncleft side. Two symmetrical vertical distances on either side of the cleft are thus formed. It is essential that the incisions in the skin correspond precisely with those on the muscles and mucosa, and that all layers are sutured with the use of the triangular flap, thus preventing vertical scar contracture. This procedure produces a symmetric, balance lip with a well-defined Cupid's bow, a symmetric vermilion, and a properly aligned orbicularis oris muscle. We had treated three patients with unilateral incomplete cleft lip by using Bardach's triangular flap method. The operation scars could be reduced comparing to Millard method because Bardach's method did not use the columella base and the alar base incision. And the flap design was more simple and accurate comparing to Tennison-Randall method. On the other hand, the postoperative scars on the philtrum pointed as a disadvantage of triangular flap method were cosmetically acceptable because the three patients had incomplete cleft lip. We have experienced that Bardach's triangular flap is a recommendable technique for the repair of unilateral incomplete cleft lip.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.32 no.5
• /
• pp.447-453
• /
• 2010

The hemifacial microsomia is characterized by variable underdevelopment of the craniofacial skeleton, external ear, and facial soft tissues. So, patients with hemifacial microsomia have an occlusal plane canting and malocclusion with facial asymmetry. Distraction osteogenesis (DO) with an intraoral or extraoral device is a technique using tension to generate new bone with gradual bone movement and remodeling. DO has especially been used to correct craniofacial deformities such as a hemifacial microsomia, facial asymmetry, and mandible defect that could not adequately be treated by conventional reconstruction with osteotomies. It has a significant advantage to lengthen soft and hard tissue of underdeveloped site without bone graft and a few complication such as nerve injury or muscle contracture. A 13-years old girl visited our clinic for the chief complaint of facial asymmetry. She had a left hypoplastic maxilla and mandible, occlusal plane canting and malocclusion. We diagnosed hemifacial microsomia and lanned DO to lengthen the affected side. Le Fort I osteotomy, left mandibular ramus and symphysis osteotomy were performed. The internal distraction devices fixed with screw on maxillary and mandibular ramus osteotomy sites. External devices were adapted to lower jaw for DO on symphysis osteotomy site and to upper jaw for rapid maxillary expansion (RME). At 7days after surgery, distraction was started at the rate of 1mm per day for 13days, and after 4months consolidation periods, distraction devices were removed. Simultaneous multiple maxillo-mandibular distraction osteogenesis with RME resulted in a satisfactory success in correcting facial asymmetry as well as occlusal plane canting for our hemifacial microsomia.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.38
• /
• pp.16.1-16.9
• /
• 2016

Background: The association of biomaterial combined with repair factor-like platelet-rich plasma (PRP) has prospective values. Bovine-derived xenograft has been identified as an osteoconductive and biocompatible grafting material that provides osseointegration ability. PRP has become a valuable adjunctive agent to promote healing in a lot of dental and oral surgery procedures. However, there are controversies with respect to the regenerative capacity of PRP and the real benefits of its use in bone grafts. The purpose of this study was to assess the influence of PRP combined with xenograft for the repair of peri-implant bone defects. Methods: Twelve rabbits were used in this study, and the experimental surgery with implant installation was performed simultaneously. Autologous PRP was prepared before the surgical procedure. An intrabony defect (7.0 mm in diameter and 3.0 mm deep) was created in the tibia of each rabbit; then, 24 titanium dental implants (3.0 mm in diameter and 8.5 mm long) were inserted into these osteotomy sites. Thus, a standardized gap (4.0 mm) was established between the surrounding bony walls and the implant surface. The gaps were treated with either xenograft alone (control group) or xenograft combined with PRP (experimental group). After healing for 1, 2, 3, 4, 5, and 6 weeks, the rabbits were sacrificed with an overdose of KCl solution. Two rabbits were killed at each time, and the samples including dental implants and surrounding bone were collected and processed for histological analysis. Results: More newly formed bone and a better bone healing process were observed in control group. The histomorphometric analysis revealed that the mean percentage of bone-to-implant contact in the control group was significantly higher than that of the experimental group (25.23 vs. 8.16 %; P < 0.05, independent-simple t test, analysis of variance [ANOVA]). Conclusions: The results indicate that in the addition of PRP to bovine-derived xenograft in the repair of bone defects around the implant, PRP may delay peri-implant bone healing.

• Journal of Korean Foot and Ankle Society
• /
• v.11 no.2
• /
• pp.177-181
• /
• 2007

Purpose: The purpose of this study is to compare the two prosthesis that used for total ankle arthroplasty. Materials and Methods: From Sept. 2003 to Jun 2006, 13 patients and 14 ankles that could be follow up more than 1 months. Semiconstrained type (Group I, 7 cases) and Unconstrained type (Group II, 7 cases) were used for total ankle arthroplasty. Mean age was 63.2 year-old, 12 ankles are men and 2 ankles were women. Mean follow up periods were 29 months. The criteria to compare the clinical result were postoperative range of motion, AOFAS score and residual bone stock of medial malleolus. Results: Postoperative range of motion of group I was $43.6{\pm}9.4$ degrees and of group II was $50.7{\pm}7.3$ degrees (p=0.115). Postoperative AOFAS score of group I was $77.1{\pm}13.0$ points and of group II was $86.0{\pm}5.7$ points (p=0.094). Resected bone stock in medial malleolus of group I was $10.7{\pm}2.5\;mm$ and of group II was $5.1{\pm}1.2\;mm$ (p=0.003). Total number of complication in our study was 9 cases. 3 cases were a malleolar fracture, two occurred at intra-operation, the other at follow-up period. Re-operation was done in 6 cases, 3 cases were calcaneal corrective osteotomy, 2 cases were resection of a heterotopic bone and one case was pedicular flap operation for skin problem. Conclusion: In our hospital, mobile bearing type prosthesis shows good result than a semiconstrained type in respect of residual bone stock in medial malleolus. Postoperative range of motion and AOFAS score between two groups shows no significant difference. But small number of patients and short term follow up period is a defect in our study, afterward more population and long term follow up period are needed.