• 한국수소및신에너지학회논문집
• /
• 제23권4호
• /
• pp.382-389
• /
• 2012

Power generation cycle using ammonia-water mixture as working fluid has attracted much attention because of its ability to efficiently convert low-temperature heat source into useful work. If an ammonia-water power cycle is combined with a power cycle using liquefied natural gas (LNG), the conversion efficiency could be further improved owing to the cold energy of LNG at $-162^{\circ}C$. In this work parametric study is carried out on the thermodynamic performance of a power cycle consisted of an ammonia-water Rankine cycle as an upper cycle and a LNG cycle as a bottom cycle. As a driving energy the combined cycle utilizes a low-temperature heat source in the form of sensible heat. The effects on the system performance of the system parameters such as ammonia concentration ($x_b$), turbine 1 inlet pressure ($P_{H_1}$) and temperature ($T_{H_1}$), and condenser outlet temperature ($T_{L_1}$) are extensively investigated. Calculation results show that thermal efficiency increases with the increase of $P_{H_1}$, $T_{H_1}$ and the decrease of $T_{L_1}$, while its dependence on $x_b$ has a downward convex shape. The changes of net work generation with respect to $P_{H_1}$, $T_{H_1}$, $T_{L_1}$, and $x_b$ are roughly linear.

• 한국태양에너지학회 논문집
• /
• 제36권4호
• /
• pp.49-56
• /
• 2016

The objective of this work is to analyze the variation in energy performance for each flat plate collector connected in series. In this study, it was assumed that solar water heating system with annual solar fraction of 60% was installed in an office building in Seoul, South Korea. The transient energy performance corresponding to four cases, which are selected using different solar radiation and outdoor air temperature, is studied by analyzing the variation in outlet temperature, solar useful heat gain, and thermal efficiency of each collector. It is observed that the useful heat gain and the collector efficiency decrease continuously, and outlet temperature increases when increasing the number of collector connected in series. The long-term performance is assessed by evaluating the thermal efficiency of each collector for two solar radiation conditions ranging from 780 to $820W/m^2$ and from 380 to $420W/m^2$. It is found that the differences between the intercept and slope of the efficiency curves for first and eighth collectors are 3.68% and 6.74% for solar radiation of $800{\pm}20W/m^2$ and 8.57% and 12.90% for solar radiation of $400{\pm}20W/m^2$, respectively. In addition, it is interesting to note that annual useful heat gain and collector efficiency are reduced with similar rate of about 6.13% when increasing the collector area by connecting the collectors in series.

• Animal Bioscience
• /
• 제37권5호
• /
• pp.832-838
• /
• 2024

Objective: The use of molecular genetic methods in pig breeding can significantly increase the efficiency of breeding and breeding work. We applied the F_st (fixsacion index) method, the main focus of the work was on the search for common options related to the number of born piglets and the weight of born piglets, since today the urgent task is to prevent a decrease in the weight of piglets at birth while maintaining high fertility of sows. Methods: One approach is to scan the genome, followed by an assessment of Fst and identification of selectively selected regions. We chose Large White sows (n = 237) with the same conditions of keeping and feeding. The data were collected from the sows across three farrowing. For genotyping, we used GeneSeek GGP Porcine HD Genomic Profiler v1, which included 68,516 single nucleotide polymorphisms evenly distributed with an average spacing of 25 kb (Illumina Inc, San Diego, CA, USA). Results: Based on the results of the Fst analysis, 724 variants representing selection signals for the signs BALWT, BALWT1, NBA, and TNB (weight of piglets born alive, average weight of the 1st piglets born alive, total number born alive, total number born). At the same time, 18 common variants have been identified that are potential markers for both the number of piglets at birth and the weight of piglets at birth, which is extremely important for breeding work to improve reproductive characteristics in sows. Conclusion: Our work resulted in identification of variants associated with the reproductive characteristics of pigs. Moreover, we identified, variants which are potential markers for both the number of piglets at birth and the weight of piglets at birth, which is extremely important for breeding work to improve reproductive performance in sows.

• 핵의학기술
• /
• 제13권1호
• /
• pp.93-97
• /
• 2009

2006년~2008년 2사분기까지의 2.5년간의 환자 건수는 14,674건이었으며, $^{18}F$-FDG 평균 주사량은 461.5 MBq 였다. 2.5년간 순환근무는 3회 이루어졌고, 10명의 방사선사 중 PET과 Gamma 영역별 1인을 제외한 8명의 순환근무가 시행되었다. 추가로 2008년 3인의 신입인력이 야간에 투입되어 이에 대한 평가도 이루어졌다. 방사선사의 근무연한은 15년 이상이 2인, 10~15년이 3인, 5~10년이 1인, 5년 미만이 3인이었다. 이들의 개인별 피폭선량은 먼저 PET실에 근무를 하고 있을 때가 Gamma 영역에 근무하고 있을 때 보다 더 높게 나왔다. 가장 큰 원인으로는 일일 처리 건수 면에서 PET과 Gamma영역의 차이가 거의 없는 상태에서 $^{99m}Tc$보다는 상대적으로 에너지가 높은 $^{18}F$-FDG를 사용하는데 있다고 본다. 특히 개인별 피폭선량도 근무연한에 따른 분기별 평가에서 서로 다르게 나타났다. 또한 순환근무 초기 1개월째보다는 업무의 연속성을 익힌 3개월째에 더 낮은 피폭선량을 보여 주고 있다. 이는 PET 실의 근무연한이 길수록 업무의 숙달도가 증가하여 개인별 피폭선량은 감소하는 것으로 보인다. 예약실에 근무하는 간호사의 피폭선량은 $^{18}F$-FDG 주사 후 짧은 시간에 환자와의 접촉이 이루어지고 있어 그리 큰 문제점을 보이지는 않았다. 그러나 임신 가능성이 있는 간호사일 경우는 이를 재고해 보아야할 필요가 있다. 순환 근무를 통한 장시간 PET/CT실을 벗어난 상황이 될 경우 대부분의 근무자가 초기 1개월에서 업무의 연속성 결여 및 개인별 피폭선량 증가라는 위험성을 내포하였다. PET/CT 환자의 증가에 따른 PET/CT실 전체의 과도한 피폭을 분산하기 위한 순환 근무제의 도입이 또 다른 문제점을 갖고 있음을 알 수 있다.5,6) 이를 해결하기 위해서는 근무자의 업무재교육과 순환 및 고정 근무제의 적절한 병행을 시행할 필요가 있다고 본다. 또한 고정 근무자는 순환 근무 인력들의 이런 문제점을 해결하기 위해 업무영역에서 표준화된 업무지침서 등을 만들어야 한다.

• Physical Therapy Rehabilitation Science
• /
• 제10권2호
• /
• pp.175-184
• /
• 2021

Objective: Fatigue can decrease both quality of life and work efficiency. Ginseng is one of the most popular herbal treatments for improving personal health, with applications in treating fatigue. However, the exact mechanisms of anti-fatigue effects are still unclear. Thus, we investigated the effect of red ginseng powder (RGP) on exercise capacity and peripheral fatigue using both behavioral and molecular experiments in mice. Design: Four-groups behavioral and molecular experiment. Methods: Male 6-weeks-old ICR mice were treated with distilled water, 100, and 200 mg/kg RGP for 5 days via oral administration. The exercise capacity of each animal group was measured by locomotor activity, rota-rod, hanging wire, and cold swimming tests. Additionally, after performing the treadmill to induce fatigue, lactate expression and molecular experiments were investigated using mice gastrocnemius. Results: Mice treated with RGP exhibited increased exercise capacity in the behavioral tests. Additionally, RGP induced a dose-dependent decrease in lactate levels after high-intensity exercise, and Monocarboxylate transporter (MCT) 4 expression increased in groups treated with RGP. However, there was no significant change in MCT1. Conclusions: These results suggest that RGP exerts several anti-fatigue properties by lower lactate and improved exercise capacity. Increased MCT4 expression may also affect lactate transport. Thus, this study suggests that the anti-fatigue properties of RGP might be associated with MCT4 activity.

• 한국산업보건학회지
• /
• 제10권1호
• /
• pp.170-178
• /
• 2000

Most of manufacturers try to produce the most efficient filter for respirators with the lowest breathing resistance. Filter performance depends on low penetration, i.e., high efficiency (%), and low pressure drop ($mmH_2O$). This study was performed to evaluate performance of respirator filters by quality factor ($q_F$) and suggest the direction for improvement of respirator filters of good quality in Korea. Two mechanical filters, S and K made in Korea, three filtering facepieces, S made in China, C made in Korea and M made in USA, which were widely used in the workplace, were selected and tested efficiency and pressure drop in accordance with flow rate, using with Automated Filter Tester Model 8110 (TSI, USA). The best quality factor within the same respirator filter categories was $0.0672cm^{-1}\;H_2O$ for mechanical filter S, $0.0698cm^{-1}\;H_2O$ for filtering facepiece M at flow rate of 32Lpm. Mechanical filter S would be the best suitable during heavy work since qulity factors decrease less sharply than any others as increased flow rates. It was necessary for mechanical filter S to lower pressure drop without increasing efficiency, but mechanical filter K should be increased efficiency and decreased pressure drop. While filtering facepiece M had the best quality performance of three ones, Sand C should get much higher efficiency and lower pressure for better performance.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 춘계학술발표대회 논문집
• /
• pp.160-165
• /
• 2008

The concern in energy reduction in the field of architecture which takes up a big weight in domestic energy consumption is gradually increasing. For this reason, a lot of research work on this matter is being carried out. Particularly, it is generally required that currently used system in a structure for energy reduction should be maximized in its efficiency. In addition, research on several energy reduction typed systems is underway. Such a research work should not only include the one in time of the present but also keep up with the trend for future-oriented research. This research paper forecasted and analyzed the trend for global warming and demand of a structure for energy in the future by applying climate scenarios to cooling degree-day and heating degree-day. Also, this research found out the decrease in heating degree-days and increase in cooling degree-days until this moment due to the progress of global warming. In addition, as for heating degree-days in the future forecasted on the basis of HadCM3, it is estimated that the range of decrease could be ever bigger starting 2040 in case of Seoul and also starting 2010 in case of Ulsan ever after respectively. In case of cooling degree-days, it is estimated that its increase range could be bigger abruptly starting 2050, and after 2080, its increase range would be much bigger.

• Tribology and Lubricants
• /
• 제33권6호
• /
• pp.269-274
• /
• 2017

Currently, fuel efficiency becomes one of critical issues for automotive industries as concerns about environmental and energy problems grow. In an automatic transmission of an automobile, a drag torque due to a viscous drag of a fluid between friction and clutch plates is one of factors that degrade fuel economy. In this work, the drag torque characteristics of a wet clutch was experimentally investigated with respect to rotational speed, temperature of automatic transmission fluid (ATF), and gap between friction and clutch plates. The experimental results showed that drag torque increases to a certain level, and then decrease to the steady state value with increasing rotational speed. This behavior may be associated with two-phase flow of air and ATF at gap between friction and clutch plates. Also, it was found that the maximum drag torque value decreased as ATF viscosity decreases with increasing temperature. However, it was shown that the point at which the maximum drag torque occurs was not significantly affected by the ATF temperature. In addition, maximum drag torque was found to decrease as the gap between friction and clutch plates increased from 0.1 mm to 0.2 mm. Furthermore, it was observed that the generation of maximum drag torque was delayed as the gap increased. The outcomes of this work are expected to be helpful to gain a better understanding of drag torque characteristic of a wet clutch, and may therefore be useful in the design of wet clutch systems with improved performance.

• 대한기계학회논문집A
• /
• 제29권10호
• /
• pp.1353-1360
• /
• 2005

Injection-molded products serve a wide range of applications in our modem lives and their significance is ever increasing. However, difficulty of communication among related companies under the present system results in increase of lead time and decrease of production efficiency. The objective of this paper is the development of a web-based draft verification system in mold design processes. Although several commercial CAD systems offer draft verification functions, those systems are very expensive and inadequate to perform collaborative works. For collaborative work under the distributed environment, the proposed system uses native file transforming of CAD data into optimal format by using the ACIS kernel and InterOp. Functions of draft verification modules are constructed over the ActiveX control using the visual C++ and OpenGL. Therefore, collaborators related to the development of a new product are able to verify the draft and undercut over the Internet without commercial CAD systems. The system helps to reduce production cost, errors and lead-time to the market. Performance of the system is confirmed through various case studies.

• 대한간호학회지
• /
• 제43권1호
• /
• pp.20-29
• /
• 2013

Purpose: The purpose of this study was to propose and test a predictive model that could explain and predict nursing productivity. Methods: A survey using a structured questionnaire was conducted with 360 nurses in Korea. The data were analyzed using SPSS Windows 18.0 and AMOS 19.0 program. Results: Based on the constructed model, burnout and organizational commitment were found to have direct effects on nurses' turnover intention and nursing productivity. While nursing work environment was found to have indirect effects on nurses' turnover intention and nursing productivity. Conclusion: This structural equational model is a comprehensive theoretical model that explains the related factors and their relationship with nursing productivity. Comprehensive organizational interventions to improve nursing productivity should focus on improving the nursing work environment. Findings from this study can be used to design appropriate strategies to decrease nurse turnover in Korea. Further studies are needed to prospectively verify these causal relationships with larger samples.