• The Journal of Advanced Prosthodontics
• /
• v.9 no.3
• /
• pp.159-169
• /
• 2017

PURPOSE. The purposes of this study were to evaluate the marginal and internal gaps, and the potential clinical applications of three different methods of dental prostheses fabrication, and to compare the prostheses prepared using the silicone replica technique (SRT) and those prepared using the three-dimensional superimposition analysis (3DSA). MATERIALS AND METHODS. Five Pekkton, lithium disilicate, and zirconia crowns were each manufactured and tested using both the SRT and the two-dimensional section of the 3DSA. The data were analyzed with the nonparametric version of a two-way analysis of variance using rank-transformed values and the Tukey's post-hoc test (${\alpha}=.05$). RESULTS. Significant differences were observed between the fabrication methods in the marginal gap (P < .010), deep chamfer (P < .001), axial wall (P < .001), and occlusal area (P < .001). A significant difference in the occlusal area was found between the two measurement methods (P < .030), whereas no significant differences were found in the marginal gap (P > .350), deep chamfer (P > .719), and axial wall (P > .150). As the 3DSA method is three-dimensional, it allows for the measurement of arbitrary points. CONCLUSION. All of the three fabrication methods are valid for measuring clinical objectives because they produced prostheses within the clinically acceptable range. Furthermore, a three-dimensional superimposition analysis verification method such as the silicone replica technique is also applicable in clinical settings.

• Membrane and Water Treatment
• /
• v.9 no.1
• /
• pp.43-51
• /
• 2018

Hollow fiber (HF) membranes are gaining wide interest over flat membranes due to their compaction and high area to surface volume ratio. This work addresses the fabrication of HF from polysulfone (PS) and polyethersulfone (PES) using N-methylpyrrolidone (NMP) as solvent in addition to other additives to achieve desired characteristics. The semi-pilot spinning system includes jacketed vessel, four spinneret block, coagulation and washing baths in addition to dryer and winder. Different parameters affecting dry-wet spinning phase inversion process were investigated. Dope compositions of PES, NMP and polyvinyl pyrrolidone (PVP) of varying molecular weights as additive were addressed. Some critical parameters of importance were also investigated. Those include dope flow rate, air gap, coagulation & washing baths and drying temperatures. The measured dope viscosity was in the range from 1.7 to 36.5 Pa.s. Air gap distance was adjusted from 20 to 45 cm and coagulation bath temperature from 20 to $46^{\circ}C$. The HF membranes were characterized by scanning electron microscope (SEM), atomic force microscope (AFM) and mechanical properties. Results indicated prevalence of finger like structure and average surface roughness from about 29 to 78.3 nm. Profile of stress strain characteristics revealed suitability of the fibers for downstream interventions for fabrication of thin film composite membrane. Different empirical correlations were formulated which enable deeper understanding of the interaction of the above mentioned variables. Data of pure water permeability (PWP) confirmed that the fabricated samples fall within the microfiltration (MF)-ultrafiltration (UF) range of membrane separation.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.32 no.3
• /
• pp.246-254
• /
• 2016

Nowadays, 3 dimentional (3D) printing, especially Direct Metal Laser Sintering (DMLS) system is used in dentistry. DMLS system has recently been introduced for fabrication metal framework for metal ceramic crowns to overcome the disadvantages of the casting method and computer aided design/computer aided manufacturing (CAD/CAM) milling system. DMLS system uses a high-temperature laser beam to selectively heat a substructure metal powder based on the CAD data with the framework design. A thin layer of the beamed area becomes fused, and the metal framework is completed by laminating these thin layers. Utilizing DMLS system to fabricate fixed prostheses is expected to achieve free-from shaping without mold and limitations from cutting tools, fabricate prostheses with complex geometry, prevent distortion and fabrication defects that inherent to conventional fabrication methods. The purpose of this case report is to demonstrate various fixed prostheses such as long span fixed prostheses, post to achieve satisfactory results in functional and esthetic aspects.

• Journal of radiological science and technology
• /
• v.41 no.6
• /
• pp.595-602
• /
• 2018

Quality control (QC) of Computed Tomography (CT) devices is based on image quality measurement on AAPM CT phantom which is a standard phantom. Although it is possible to control the accuracy of the CT apparatus, it is expensive and has a disadvantage of low penetration rate. Therefore, in this study, we make image quality measurement phantom at low cost using FFF (Fused Filament Fabrication) type three-dimensional printer and try to analyze the usefulness, compare it with existing standard phantom. To print a phantom, We used three-dimensional printer of the FFF system and PLA (Poly Lactic Acid, density: $1.24g/cm^3$) filament, and the CT device of 64 MDCT (Aquilion CX, Toshiba, Japan). In addition, we printed a phantom using three-dimensional printer after design using various tool based on existing standard phantom. For image quality evaluation, AAPM CT phantom and self-generated phantom were measured 10 times for each block. The measured data were analyzed for significance using the Mannwhiteney U-test of SPSS (Version 22.0, SPSS, Chicago, IL, USA). As a result of the analysis, phantom fabricated with three-dimensional printer and standard phantom showed no significant difference (p>0.05). Furthermore, we confirmed that image quality measurement performance of a phantom using three-dimensional printer is similar to the existing standard phantom. In conclusion, we confirmed the possibility of low cost phantom fabrication using three dimensional printer.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.327-330
• /
• 1998

A 2watts MMIC(Monolithic Microwave Integrated Circuits) SSPA(Solid State Power Amplifiers) for 20GHz band communication systems has been designed, manufactured and measured. The 0.15um pHEMT technologywith the gate size of 400um for single device was used for the fabrication of MMIC Power Amplifier chips. The precision MIC patterns for the peripherals like power combiner/divider and microstrip lines were realized using hard substrate for gold wire/ribbon bonding. The measured data shows that this MMIC SSPA has the linear gain of 18dB, output power of 33.42dBm(2.2Watts)at 20~21GHz.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.05a
• /
• pp.163-166
• /
• 2002

For the development of an all composite unmanned aerial vehicle (UAV), manufacturing consideration in design phase, works for composite parts fabrication, subassembly and final assembly are summarized. In design phase, to maximize the advantage of composite material, manufacturing processes such as cocuring, cobonding and secondary bonding are introduced. For the curing of designed parts, composite tools are designed and manufactured. Assembly jigs are designed to satisfy dimensional tolerance of the structure. Inspection criteria are established and applied to the manufacturing. Technical data about inspection items and methods are summarized as manufacturing specifications for the mass production of the UAV structure.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.56-60
• /
• 1996

This paper presents the initial results of development of a inertial navigation grade silicon pendulous accelerometer. This effort focused on developing a bulk-micromachined silicon pendulum and designing a PI-servo controller. Performance data presented in this paper includes threshold, bias short term stability and nonlinearity of scale factor. This accelerometer developed is demonstrated the feasibility of meeting one-nautical-mile-per-hour accuracy.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2000.02a
• /
• pp.39-42
• /
• 2000

The cryostat with refrigerator for whole body MRI had been designed and fabrication data were discuss in this paper. These results will be applied to commercial MRI cryostat in the fucature.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.42-45
• /
• 2002

Small sized LTPS TFT-LCDs are developed and evaluated. Sine the fabrication process is optimized for the productivity of huge glass substrate, the pattern size is above 5${\mu}m$. The panels with integrated digital data drivers are not satisfactory to compete with a-Si technology. Therefore, LTPS panels are implemented by PMOS technology and it is proved that they can be competitive with a-Si TFT-LCDs in terms of performance and cost.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.10-11
• /
• 2003

Metal nanoparticle doped glasses have various applications such as use as photochromic media for optical disk data storage, the fabrication of optical waveguides and waveguide lasers, use as all-optical switches due to their nonlinear optical properties, as well as use in the color glass recycling industry. Recently, an ultrashort pulsed laser has been used as a powerful tool to make microscopic modifications to transparent Metal nano particle doped glasses. (omitted)