• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.6
• /
• pp.1010-1016
• /
• 2004

In this paper, a scheme for estimating the parameters of solar cells and a NN-based emulator for predicting the maximum power point are presented. The diode model with series and shunt resistors is used to estimate parameters highly affecting its V-I characteristic curve and both a real-coded genetic algorithm and the model adjustment technique are employed. For implementing the emulator, a multi-layered neural network incorporating with the BP algorithm is used. A set of simulation works using both field data and generated data are carried out to demonstrate the effectiveness of the proposed method.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.7
• /
• pp.963-968
• /
• 2013

Ionizing Radiation effects on MOS devices provide useful information regarding the behavior of MOS based devices and circuits in the electronic instrumentation parts and instructive data for making the high sensitive sensors. The study presents the results of the analysis on the structural characteristics of MOS capacitor for sensing the ionizing radiation effect. We performed numerical modeling of Ionizing-radiation effect on MOS capacitor and simulation using Matlab program. Also we produced MOS capacitors and obtained useful data through radiation experiment to analyse the characteristic of ionizing radiation effect on MOS capacitor. Increasing the thickness of MOS capacitor's oxide layer enhanced the sensitivity of MOS capacitor under irradiation condition, but the sensitivity of irradiated MOS capacitor is uninfluenced by the area of MOS capacitor. The high frequency capacitance of the MOS capacitor is found to be strongly affected by incident ionizing radiation.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.10
• /
• pp.1790-1795
• /
• 2008

Energy scavenging is a technique that converts ambient energy, for example, vibration and light, to electrical energy in order to supply power to low power electronic devices such as ubiquitous sensors. In this paper, we propose an optimal operation condition of power delivery circuit and design strategy for energy scavenging system in which the generated power is order of microwatt and, consequently, efficient handling of power is critical. We also propose that high data transmission rate is more realistic optimal design objective rather than high energy efficiency. It is shown that disconnection of load from the storage capacitor right after data transmission reduces energy wasting and that optimal value of storage capacitor can be determined at this condition. The feasibility of our propose is proved by experiments and we believe that the proposed design strategy will promote the application of piezoelectric micropower generator to the ubiquitous sensor networks.

• Radiation Oncology Journal
• /
• v.12 no.2
• /
• pp.219-223
• /
• 1994

This paper describes the basic data measurements for total body irradiation with 6 Mv photon beam including compensators design. The technique uses bilateral opposing fields with tissue compensators for the head, neck, lungs, and legs from the hip to toes. In vivo dosimetry was carried out for determining absorbed dose at various regions in 7 patients using diode detectors(MULTIDOSE,k Model 9310, MULTIDATA Co., USA). As a results, the dose uniformity of${\pm}3.5{\%}$(generally, within${\pm}10{\%}$can be achieved with out total body irradiation technique.

• 한국정보통신설비학회:학술대회논문집
• /
• 2003.08a
• /
• pp.93-95
• /
• 2003

We have designed and fabricated a micromirror array using single crystalline silicon (SCS) for data communication applications. The mirror array has $16{\times}16$ micromirrors and each mirror has $120{\mu}m{\times}100{\mu}m$ reflective surface. Electrostatic force was adopted as a driving mechanism. The spring dimensions were determined using relationship between spring dimensions and driving voltage. The designed tilting angle was $9.6^{\circ}$, and measured tilting angle according to applied voltages were experimented. The response time was measured using He-Ne laser and position sensitive diode (PSD), and lifetime was checked for reliability proof.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1436-1439
• /
• 2005

A novel current-type data driver for active matrix organic light emitting diode (AMOLED) is proposed for current uniformity enhancement among its output channels. New architecture is composed of shadow DACs that precharge output stages, a single-real DAC that correct the output level to a real target current level and output stages that operate in 3 states of sampling, correcting and driving. Simulation results show that the proposed driving method and circuits improve the current uniformity among output channels of a current-type driver IC.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.5
• /
• pp.1304-1316
• /
• 1996

In this paper, A VCO(Voltage Controlled Oscillator) in use of clock recovery/data regeneration circuit for 10 Gbps fiber optic receivers was developed. The improved hair-pin resonator with a parallel coupled lines, which has been applied to microstrip filters, was used as a resonance part. As a frequcncy tuning device by substituting 3-terminalMESFET vaaractor for varactor diode, an MMIC manufacturing process will be simplified. Since a hair-pin resonator is planar type compared to the dielectric resonator and has a relatively flat reactance verus frequency, it will be favorable to apply a hair-pin resonator to an MMIC, in addition wideband frequency tuning range is able to be obtained.

• 한국가시화정보학회:학술대회논문집
• /
• 2004.11a
• /
• pp.1-4
• /
• 2004

The PIV measurements are performed to get the quantitative flow visualization around a road vehicle. The model scaled with 1/48 is located in the middle test section of the closed-loop water tunnel and the measuring system consists of CCD camera, diode laser, synchronizer, and computer. The experimental data are obtained at two Reynolds numbers of 50,000 and 100,000 based on the model length. The quasi-three-dimensional isovorticity surfaces, based on two-dimensional velocity field data, are generated. There is little difference between the results in part of the recirculation region and the vorticity contour according to the Reynolds number. Also a little bit complicated three dimensional flows are predicted behind the road vehicle.

• Journal of Welding and Joining
• /
• v.19 no.2
• /
• pp.208-214
• /
• 2001

In this study, we constructed a visual sensor system for weld seam tracking in real time in GMA welding. A sensor part consists of a CCD camera, a band-pass filter, a diode laser system with a cylindrical lens, and a vision board for inter frame process. We used a commercialized robot system which includes a GMA welding machine. To extract the weld seam we used a inter frame process in vision board from that we could remove the noise due to the spatters and fume in the image. Since the image was very reasonable by using the inter frame p개cess, we could use the simplest way to extract the weld seam from the image, such as first differential and central difference method. Also we used a moving average method to the successive position data or weld seam for reducing the data fluctuation. In experiment the developed robot system with visual sensor could be able to track a most popular weld seam. such as a fillet-joint, a V-groove, and a lap-joint of which weld seam include planar and height directional variation.

• Journal of Sensor Science and Technology
• /
• v.29 no.3
• /
• pp.180-186
• /
• 2020

In this study, we applied edge-pulse modulation to prevent the flicker of light-emitting diode (LED) light in a visible light identification system. In the visible light transmitter, positive pulses were transmitted at the edges of the low-to-high transition points, and negative pulses were transmitted at the edges of the high-to-low transition points of the non-return-to-zero (NRZ) data waveforms. In the visible light receiver, the NRZ waveforms were regenerated by making low-to-high and high-to-low transitions at the point of the positive and negative pulses, respectively. This method has two advantages. First, it ensures that the LED light is flicker-free because the average optical power of the LED was kept constant during data transmission in the transmitter. Second, the 120 Hz optical noise from the adjacent lighting lamps was easily cut off using a simple RC-high pass filter in the receiver.