• Earthquakes and Structures
• /
• 제26권5호
• /
• pp.383-400
• /
• 2024

For a conventionally repaired frame-supported-transfer-slab (FSTS) reinforced concrete (RC) structure, both the transfer slab and the beam-to-column and transfer slab-to-column joints remain vulnerable to secondary earthquakes. Aimed at improving the seismic performance of a damaged FSTS RC structure, an innovative retrofitting scheme is proposed, which adopts the sector lead rubber dampers (SLRDs) at joints after the damaged FSTS RC structure is repaired by conventional approaches. In this paper, a series of quasi-static cyclic tests was conducted on a large-scale retrofitted FSTS RC structure. The seismic performance was evaluated and the key test results, including deformation characteristics, damage pattern, hysteretic behaviour, bearing capacity and strains on key components, were reported in detail. The test results indicated that the SLRDs started to dissipate energy under the service level earthquake, and thus prevented damages on the beam-to-column and transfer slab-to-column joints during the secondary earthquakes and shifted the plastic hinges away from the beam ends. The retrofitting scheme of using SLRDs also achieved the seismic design concept of 'strong joint, weak component'. The FSTS RC structure retrofitted by the SLRDs could recover more than 85% bearing capacity of its undamaged counterpart. The hysteresis curves were featured by the inverse "S" shape, indicating good bearing capacity and hysteresis performance. The deformation capacity of the damaged FSTS RC structure retrofitted by the SLRDs met the corresponding codified requirements for the case of the maximum considered earthquake, as set out in the Chinese seismic design code. The stability of the FSTS RC structure retrofitted by the SLRDs, which was revealed by the developed stains of the RC frame and transfer slab, was improved compared with the undamaged FSTS RC structure.

• 한국산학기술학회논문지
• /
• 제18권3호
• /
• pp.694-702
• /
• 2017

선하역사의 경우 차량-궤도에서 발생하는 하중 및 진동이 직접적으로 전달되는 구조적 한계로 인하여 발생하는 구조체 전달 형태의 진동과 소음레벨이 다른 역사형식 대비 월등히 높음으로 인하여 역사 내 상업 및 업무시설 이용객과 종사자들의 불편과 민원이 증가하고 있다. 선하역사에 발생하는 소음 진동을 저감하기 위한 대책중 하나로 알려진 플로팅 궤도의 경우 궤도 하부에 고무 마운트나 패드 요소를 적용한 장치가 주로 설치되어 댐퍼 역할을 한다. 이러한 장치의 경우, 열차 운행 시 발생하는 비선형 하중에 대하여 정확한 강성 및 감쇠비를 설계하기 어렵다는 단점이 있다. 본 연구에서는 플로팅 궤도에 적용 가능하며 정확한 강성 설계가 가능한 마찰 쐐기형 방진장치를 소개한다. 또한, 방진장치 강성 설계값과 시험값을 비교 분석하고 마찰 쐐기형 블록 배치에 따른 감쇠비를 열차 하중조건에 따라 도출하였다. 방진장치의 성능시험은 DIN45673-7 규정에 의거하여 진행하였으며 시험항목인 정적 및 동적하중 시험을 모두 포함한다. 성능시험 하중조건은 DIN 규정에 따라 열차 및 궤도 중량을 고려하여 적용하였으며 수직 하중 및 수평 하중에 대한 시험을 진행하여 방진장치 적용에 따른 궤도의 구조안전성을 확보한다. 더불어, 하중재하속도에 따른 마찰재의 마찰계수 변화 양상을 확인함으로서 다양한 하중재하속도 조건에 대한 마찰쐐기형 방진장치의 진동저감 성능을 확인한다.

• 인터넷정보학회논문지
• /
• 제15권1호
• /
• pp.171-178
• /
• 2014

본 논문에서는 실시간으로 가상현실의 증강객체에 외부의 힘이 작용할 때 증강된 가상 객체의 동적 모델링 방법을 제시하였다. 가상객체의 자연스러운 움직임을 시뮬레이션 하기 위하여 AR 객체에 적용되는 외부의 힘의 변화에 대하여 Newton의 운동법칙을 적용하여 객체의 움직임을 설명하는 식을 생성하였다. 동적 모델링 과정에서 증강된 객체와 햅틱 장비간의 실질적 상호작용이 발생하며 이때 외부의 힘이 가상객체에 전달된다. 증강된 객체의 고유특성은 강체 혹은 탄성체의 성질을 갖는 모델이다. 강체의 동적 모델링에서는 선형 모멘텀과 각속도 모멘텀을 모두 고려하여 증강된 객체와 햅틱 스틱이 충돌할 때 수행하였다. 비강체의 동적 모델링에 있어서는 탄성체의 변형 모델은 내외의 힘과 제한요소에 자연적으로 반응하기 때문에 물리기반 시뮬레이션 방법을 적용하였다. 증강된 탄성체는 햅틱 인터페이스를 통해 사용자에 의하여 발생하는 힘의 특성과 모델의 고유 특성에 따라 자연스럽게 변형된다. 변형 물체의 모델링을 위하여 Newton의 제 2 운동법칙이라 불리는 질량-스프링 연결 시스템을 적용하였다. 실험을 통하여 증강된 강체와 비강체의 성질을 지닌 가상 객체에 햅틱 장비에 의한 햅틱 상호작용이 발생 할 때 객체의 변환을 자연스럽게 가시화 할 수 있었다.

• 한국산학기술학회논문지
• /
• 제20권1호
• /
• pp.464-469
• /
• 2019

본 논문에서는 화생방 방호시설에 사용되는 가스 차단밸브를 비롯한 각종 밸브 및 출입통제 챔버를 제어할 수 있는 원격 감시패널과 제어시스템을 개발하였다. 원격 감시패널은 화생방 통제실에 설치되는 메인 패널과 청정 기계실에 설치되는 보조 패널로 구성하였으며, 그 크기를 순수 제어용과 CCTV를 포함한 제어용으로 구분하여 개발하였다. 본 시스템은 방폭문 및 가스 차단문이 전시 및 평시에 발생할 수 있는 상황별 상태에 따라 원격 감시 및 제어가 가능하며, 평시모드와 전시모드로 구분하여 각 모드 작동시 추가적인 활성창을 통하여 제어 정보를 표시한다. 특히, 화생방 방호시설 내부의 각종 밸브 및 센서 그리고 각종 여과기의 동작상태를 주기적으로 센싱하여 각각의 기구 및 기기들의 정상동작 여부를 파악하며, 수리 및 교체가 필요할 경우 이를 원격으로 상황 근무자에게 경보함으로써 위급상황에서 각각의 기기들의 동작이상으로 인한 피해를 미연에 방지한다. 이를 통하여 화생방 상황 발생시 차단밸브 및 양압밸브의 상태에 따른 송풍기, 급기 및 배기 댐퍼의 작동, 비상 발전기 및 냉각수 펌프 등의 제어가 가능하여 재래식 무기 및 핵폭발에 의한 폭풍압의 급격한 유입으로 인한 피해를 예방할 수 있다.

• Journal of Biosystems Engineering
• /
• 제2권1호
• /
• pp.7-24
• /
• 1977

This paper is the forth and fifth one of the study on balanced type oscillating mole drainer. In the light of the results from previous reports about the model tests, some design criteria were established and a prototype machine was set up for experimental purpose. Motion characteristics and functionof the each parts of the machine were checked and analyzed. After that, performance tests of the prototype machine were carried out in thefield. Obtained results are summarized as follows ; 1. Ten centimeter of the bullet diameter was determined so as to be able to attach it to the tractors with capacity of 30 PS to 40 PS. 2. To maintain the balance between the moments of the front shank and rear shank, the oscillating amplitude of the rear bullet was determined to be larger than that of the front bullet. At the same time , the oscillating direction of the rear bullet was designed with the inclines of ten to thirty degrees. 3. An octagonal dynamo transduced was developed for measuring the compressive force of the upper link is measuring the draft force of the machine. Acceptable linear relationship between forces and strain responses from O.D.T. was obtained. 4. Analysing the balancing mechanism of the acting part of the machine , it was found that the total draft force of the machine was equal to the difference between the sum of the draft force produced from the right and left side bending moments of the lower drawber and the compressive force on the upper link. 5. There are acceptable linear relationship between the strain and twisting moment by driving shaft, and between strain and shank moment. Above results enable us to carry out the field experiment with prototype machine. 6. When the test machine was used in the field, it was possible to reduce the oscillating acceleration by forty percent in average as compared it with the single bullet mole drainer. 7. When the test machine was used under the oscillating condition, the dratt torce was reduced by 27 percent to 59 percent as compared it with the test machine under non-oscillating condition, while the draft force was increased by 7 percent to 20 percent as compared it with the mole drainer having oscillating single bullet. The reasoning behind this fact was considered as the resistance force due to the rear shank and bullet. 8. As the amplitude and frequency of the bullet were increased, the torque was increased accordingly. This tendency could be varied with the various characteristics of the given soils. And the larger frequency and amplitute, the more increasing oscil\ulcornerlating power but decreasing draft brce were needed, and draft force was increased as the velocity was increased.9. When the amplitude of the rear bullet was designed to be larger than that of the front bullet, the minimum value of the moment was lowered and oscillating acceleration was reduced. And when the oscillating direction of the rear bullet was declined back\ulcornerwards, oscillating acceleration was increased along with the increasing angle of decli\ulcornernation. When the test machine was operated in high speed, the difference between maximum moments and minimum ones became narrow. This varying magnitude of moments appeared on the moment oscillogram seems to be correlated to the oscillating acceleration and draft force. 10. From the analysis of variance, it was found that those factors such as frequency, amplitude, and operating velocity significantly affected in the oscillating acceleration, the draft resistance, the torque, the moment, and the total power required. And interaction between frequency and amplitude affected in the oscillating acceleration. 11. Within the given situation of this study, the most preferable operating conditions of the test machine were 7 Hz in oscillating frequency, 0.54 m/sec in operating velocity, and 39.1 mm in oscillating amplitude of front and rear bullets. However, it is necessary to select the proper frequency and magnitude of oscillation depending on the soil properties of the field in which the mole drainer is practiced by use of a bal1nced type oscillating mole drainer. 12. It is recommended that a comparative study of the mole drainers would be performed in the near future using two separate balanced oscillating bullet with the one which is operated by oscillating the movable bullet in a single cylinder or other balanced type which may be single oscillating bullet with spring, damper or balancing weight, and that of thing. To expand the applicability of the balanced type oscillating mole drainer in practical use, it is suggested to develop a new mechanism which perform mole drain with vinyl pipe or filling material such as rice hull.