• 전기학회논문지
• /
• 제56권7호
• /
• pp.1255-1260
• /
• 2007

[ $TiO_2-V_2O_5$ ] sol was prepared using sol-gel method. Sol changed to gel with hydrolysis and polymerization. DTA properties of gel powder had endothermic reaction due to evaporation of propanol about $80^{\circ}C$, had exothermic reaction due to combustion of propanol about $230^{\circ}C$ and had exothermic reaction due to combustion of alkyl group about $350^{\circ}C$. Crystalline properties of gel powder retained amorphous phase at $50^{\circ}C$, retained anatase phase from $400^{\circ}C\;to\;600^{\circ}C$ and had all rutile phase over $700^{\circ}C$ at 0.01mole $V_2O_5$ additive. The capacitance of thin films increased with increasing heat treatment temperature and thin films had best properties at $700^{\circ}C$. The capacitance of thin films increased a lot with decreasing measurement frequency.

• 한국세라믹학회지
• /
• 제39권8호
• /
• pp.721-727
• /
• 2002

고함량 PbO계 조성 PDP 격벽용 유리의 경우, 광학적, 기계적 및 전기적 물성들을 만족시키며, 동시에 높은 온도에서 열처리공정을 거쳐야 하므로, 유리의 조성-물성-공정상의 trade-off가 발생하여, 이를 극복하기 위한 방안으로서 유리의 결정화가 유효하다. 이에 본 연구에서는 고함량 PbO계 조성 PDP 격벽용 후보 유리계의 최적결정화조건을 확립하고자 열시차분석법(DTA)에 의한 결정화 특성을 연구하였다. $62PbO-19B_2O_3-10SiO_2-9(Al_2O_3-K_2O-BaO-ZnO)$(in wt%) 조성계의 유리에 결정핵생성 및 성장을 위해 $TiO_2$를 3 wt%를 첨가한 수, 용융/냉각/분쇄 처리 후 얻어진 유리 분말을 $445^{\circ}C$에서 각각 1∼10시간 열처리하여 핵생성을 시켰으며, 이렇게 얻어진 각 유리 분말은 각기 $5∼25^{\circ}C/min$의 가변 승온속도로 DTA 측정을 하였다. DTA 결정화 피크 온도는 승온속도가 높아짐에 따라 증가하였고, 열처리 시간이 증가함에 따라 감소하였다. Avrami 변수는 1에 근사하는 값이 얻어져서, 표면결정화가 우선하였으며, 최대 핵생성 처리시간은 2시간이었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 연구회
• /
• pp.114-117
• /
• 2001

$(Ba_{0.6-x}Sr_{0.4}Ca_x)TiO_3$(x=0.10, 0.15, 0.20) ceramics were fabricated by the mixed-oxide method and their structural and dielectric properties were investigated with variation of composition ratio and sintering temperature. As a result of the differential thermal analysis(DTA), exothermic peak was observed at around $1020^{\circ}C$ due to the formation of the polycrystalline perovskite phase. BSCT(50/40/10) specimen sintered at $1500^{\circ}C$ showed the highest average grain size(18.25$[{\mu}m]$). Curie temperature and dielectric constant at room temperature decreased with increasing amount of Ca. BSCT(50/40/10) specimen sintered at $1450^{\circ}C$ showed a good dielectric constant, K, (=4324) and dielectric loss, $tan{\delta}$, (=0.972%) properties at 1[KHz].

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.359-360
• /
• 2005

PZT(20/80) and PZT(80/20) powders, prepared by the sol-gel method, were mixed with an organic vehicle and the PZT(20/80)/PZT(80/20) heterolayered thick films were fabricated by the screen-printing method on Pt/$Al_2O_3$ substrates. The structural properties such as DTA, X-ray diffraction and microstructure, were examined as a amount of the excess PbO. In the DTA analysis, the formation of the polycrystalline perovskite phase was observed at around $880^{\circ}C$. The average thickness of the PZT heterolayered thick films was approximately $80{\mu}m$.

• 한국세라믹학회지
• /
• 제39권2호
• /
• pp.113-119
• /
• 2002

The effect of ultrasonic radiation is reported for silica-poly(ethylene glycol) system prepared without the solvent using sol-gel processing by varying various parameters such as ultrasonic irradiation time, PEG content and HCl/TEOS molar ratio. The property of sonogel is compared with classic gel which has been prepared with ethanol as a solvent by traditional sol-gel processing. SEM, BET, DTA-TGA, density and Vickers hardness measurements are carried out for analyzing the samples. The gelation time is found strongly dependent on radiation time, PEG content and pH value, and has been discussed on the basis of existing theories. The $SiO_2-10$ & 20 wt% PEG sonogel exhibited superior optical, physical and gel properties as compared to the classic gel, hence, found suitable for device applications. The ultrasonic radiation increased the density and surface area, and also reduced the pore size which is well supported by the shift in the peak of DTA curve. The DTA thermogram was found similar to that of pure silica gel.

• 태양에너지
• /
• 제12권2호
• /
• pp.18-27
• /
• 1992

졸-겔 기술에 의해 $WO_3$ 다충박막이 유리와 ITO coated glass 위에 증착되었다. 특성은 XRD, 분광광도계, DTA/TGA, SEM/EDAX 그리고 RBS에 의해서 분석되었다. 균질한 $WO_3$막은 유리기판위에 dipping속도 5mm/s에서 증착 되었으며 이 시료는 희석된 HCI 전해액을 사용하여 착색시킨 결과 낮은 근적외선 투과율을 나타내었다. DTA 결과 $380^{\circ}C{\sim}500^{\circ}C$ 범위의 gel data는 $WO_3$의 결정화 온도 형성을 결정하였으며 이 측정치는 졸-겔 박막의 결정화 온도와 일치하였다. RBS에 의해 착색되지 않은 $WO_3$ 졸-겔 막의 화학조성은 $WO_3$였다.

• 한국기계가공학회지
• /
• 제11권1호
• /
• pp.7-12
• /
• 2012

Chemical mechanical polishing(CMP) technology is faced with the challenge of processing new electronic materials. This paper focuses on the balance between chemical and mechanical reactions in the CMP process that is required to cope with a variety of electronic materials. The material properties were classified into the following categories: easy to abrade(ETA), difficult to abrade(DTA), easy to react(ETR) and difficult to react(DTR). The chemical and mechanical balance for the representative ETA-ETR, DTA-ETR, ETA-DTR and DTA-DTR materials was considered for defect-free surfaces. This paper suggests the suitable polishing methods and examples for each electronic material.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제55권7호
• /
• pp.349-353
• /
• 2006

[ $TiO_2-Nb_2O_5$ ] sol was prepared using sol-gel method. Crystalline properties of gel powder changed from rutile phase to anatase phase with increasing $Nb_2O_5$ additives at $800^{\circ}C$, while they retained rutile phase regardless of $Nb_2O_5$ additives at $900^{\circ}C,\;1,000^{\circ}C$. They retained amorphous phase from $50^{\circ}C\;to\;400^{\circ}C$, retained anatase phase from $500^{\circ}C\;to\;600^{\circ}C$ and had rutile phase over $700^{\circ}C$ at 1mole% $Nb_2O_5$ additive. After $TiO_2-Nb_2O_5$ sol retained low viscosity with normal chain structure for a long time, its viscosity increased fast with network structure. DTA properties of gel powder had endothermic reaction due to evaporation of propanol and water about $78^{\circ}C$, had exothermic reaction due to propanol combustion about $290^{\circ}C$ and had exothermic reaction due to changing of $TiO_2$ phase about $640^{\circ}C$.

• Communications for Statistical Applications and Methods
• /
• 제7권3호
• /
• pp.959-966
• /
• 2000

A dimensionality assessment procedure DETECT uses the property of being near zero of conditional covariances as an indication of unidimensionality .This study provides the convergent properties to zero of conditional covariances when the dta is unidimensional, with which DETECT extends its theoretical grounds.

• 한국세라믹학회지
• /
• 제54권6호
• /
• pp.525-529
• /
• 2017

To improve the thermal resistance of a porous borosilicate lining block, we prepared and applied polysiloxane-fumed silica-ethanol slurry on top of the block and fired the coating layer using a torch for 5 minutes at $800^{\circ}C$. We conducted magnified characterizations using a microscope and XRD analysis to observe phase transformations, and TGA-DTA analysis to determine the thermal resistance. Thermal characterizations showed improved heat resistance with relatively high polysiloxane content slurry. Cross-sectional optical microscope observation showed less melting near the surface and decreased pore formation area with higher polysiloxane content slurry. XRD analysis revealed that the block and coating layer were amorphous phases. TGA-DTA analysis showed an endothermic reaction at around $550^{\circ}C$ as the polysiloxane in the coating layer reacted to form SiOC. Therefore, coating polysiloxane on a borosilicate block contributes to preventing the melting of the block at temperatures above $800^{\circ}C$.