• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.1
• /
• pp.63-68
• /
• 2011

Many countries all over the world have been doing lunar exploration projects. Korea has also been doing basic research on lunar exploration. The development of communication systems for lunar exploration projects is one of the most important aspects of performing a successful lunar mission. In this paper, we design a DSP (Digital Signal Processor) prototype based on the requirement analysis of a communication link for lunar exploration and implement its core module considering the international standards for deep space communications to perform a basic research on baseband processor development. It is verified by comparing the bit error rate of the DSP prototype with that of a computer simulation.

• ETRI Journal
• /
• v.31 no.6
• /
• pp.732-740
• /
• 2009

This paper describes the implementation of a digital audio effect system-on-a-chip (SoC), which integrates an embedded digital signal processor (DSP) core, audio codec intellectual property, a number of peripheral blocks, and various audio effect algorithms. The audio effect SoC is developed using a software and hardware co-design method. In the design of the SoC, the embedded DSP and some dedicated hardware blocks are developed as a hardware design, while the audio effect algorithms are realized using a software centric method. Most of the audio effect algorithms are implemented using a C code with primitive functions that run on the embedded DSP, while the equalization effect, which requires a large amount of computation, is implemented using a dedicated hardware block with high flexibility. For the optimized implementation of audio effects, we exploit the primitive functions of the embedded DSP compiler, which is a very efficient way to reduce the code size and computation. The audio effect SoC was fabricated using a 0.18 ${\mu}m$ CMOS process and evaluated successfully on a real-time test board.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.6
• /
• pp.1099-1106
• /
• 2017

In this paper, a three phase inverter control methodology for photovoltaic generation system, which is a renewable energy source, was studied. The voltage source inverter type of the constant voltage supply type was selected as the three phase photovoltaic inverter, and SWPM method was selected as control technique. a small capacity three phase photovoltaic inverter system, which has a DSP with powerful high speed data processing ability as the main controller and a solar controller as current controller to supply a certain amount of current to charge the battery, was made and tested for SPWM function.

• Journal of Broadcast Engineering
• /
• v.8 no.2
• /
• pp.116-125
• /
• 2003

In this paper, we introduce a newly developed DSP module and Software which Is applicable to DTV-OCR and is designed to cancel the interference signal. In general, RF repeater has problems of system oscillation and signal Quality degradation due to feedback interference signal coming from transmit antenna. In this paper, we demonstrate newly developed DSP HW and SW module for cancelling the interference signal by investigating the field data measured through a RF repeater. Also, the structure and signal processing method for non-regenerative repeater system based on the newly developed DSP HW and SW module is illustrated as well.

• Journal of Power Electronics
• /
• v.5 no.3
• /
• pp.180-189
• /
• 2005

In this paper a DSP based control scheme for the interleaved boost converter is presented. The mathematical model for the interleaved boost converter operating in a continuous inductor current mode is developed. A state-space averaging technique is used for modeling the converter system. A fixed frequency sliding mode controller is designed to ensure current distribution between the two converter modules and to achieve the load voltage regulation simultaneously. Necessary and sufficient conditions, using variable structure theory, are derived for the sliding mode to exist. The range of sliding mode controller coefficients is also determined. The designed controller capability, load distribution among the individual boost cells and load voltage regulation against source and load disturbances, are demonstrated through PSIM simulation results. A real-time controller based on ADMC401 DSP is developed. Experimental results are provided to validate the proposed control scheme.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.2
• /
• pp.118-125
• /
• 2022

With the aim to maximize the use of a given voltage source in the field of railway and electric vehicles, this study applies a technique for controlling the overmodulation region between the linear and the six-step regions. High linearity overmodulation techniques that do not use look-up table (LUT) to digital signal processor (DSP) using carrier based pulse width modulation (PWM) are proposed. Such technique requires the phase of the voltage vector at the point where the circular trajectory of the voltage command vector and hexagonal cross each other. Therefore, a method is proposed to obtain a phase of a voltage vector that is derived through an equation and applied to a carrier-based PWM. Validity of the proposed implementation method is confirmed through simulation and experiment.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.11
• /
• pp.1109-1117
• /
• 2017

In this work, a new control module and communication system associated with DSP are proposed to overcome the limitations of the contemporary prevailing PLC-based industrial equipment controller, and the performance of the proposed system was experimentally verified. In the light of this issue, a communication conversion scheme from RS-485 to Modbus, the dominant communication protocol used by PLC, was developed and shown to yield enhanced compatibility between devices. The proposed system allows for ~50％ cost reduction as well as downsizing of the industrial controllers. Furthermore, the design includes 24 V general digital I/O pins, which facilitate partial expansion of inputs and outputs. With Modbus communication implemented in DSP with the RS-485 interface, multi-to-multi communication may also be achieved.

• The Journal of the Acoustical Society of Korea
• /
• v.40 no.3
• /
• pp.247-253
• /
• 2021

Directional ultrasonic speakers that are used to hear sound only in a specific area have been continuously researched on various improvements in terms of sound quality and cost compared to general speakers. In this paper, we propose a DSP based hybrid-type ultrasonic speaker that can be heard at the same time as a general speaker in order to compensate for the sound in the low-band range, considering that it is difficult to hear the low-band sound below 500 Hz due to the sensor characteristics of the ultrasonic speaker. In the case of the system that is implemented by simply connecting a general speaker and an ultrasonic speaker, there are issues of high cost and difficulties of control as two amplifiers are used to playback ultrasonic and general sound sources. In addition, sound quality deteriorates due to the difference in playback time between ultrasonic and general sound sources. In order to improve issues of cost, control and sound quality, we developed hybrid-type ultrasonic speaker with a DSP based amplifier that can simultaneously playback by synchronizing the general sound source with the regenerated ultrasonic sound source, in addition to implement the existing CODEC functions such as Dynamic Range Control (DRC) and Equalizer (EQ).

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.3
• /
• pp.208-214
• /
• 2003

Because the digital control includes microprocessor different from an analog control, the digital control enables to monitor internal parameters of DC-DC converter and to control output voltage remotely by communicating with a Window based PC and also to monitor whether exact voltage is output or not. These things are impossible in an analog control. In this paper, a simple buck converter controlled by DSP(TMS320C31) is implemented. This converter outputs 0V to 5V from 15V input voltage and is controlled by a PD algorithm using DSP. Finally the response characteristics of a step reference voltage and in a steady state are analyzed to verify the usefulness of this digital controlled converter.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.12C
• /
• pp.1617-1622
• /
• 2004

MPEG/Audio decoder for mobile multimedia systems requires low power consumption. Implementations of AV decoder using a single RISC processor often need high power consumption owing to cash-miss in case of insufficient cash memory. In this paper, we present a MPEG/Audio decoder for mobile handset applications and implement it on a RISC processor embedding a minimized DSP accelerator. Audio decoding algorithm is splined into two parts; computation intensive and control intensive parts. Those parts we, respectively, allocated to DSP and RISC core, which are designed to run in parallel to increase the processing efficiency. The proposed system implements MP3 and AAC decoders at l7MHz and 24MHz clocks, which are reductions of 48% and 40% of complexities in comparison with implementations on a single RISC processor. The proposed method is adequate for mobile multimedia applications with insufficient cash memory.